Results
98-08-11: This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 98-08-11 that was sent previously to all known U.S. owners and operators of certain McDonnell Douglas Model MD-11 and MD-11F series airplanes by individual notices. This AD requires opening the circuit breaker of the pneumatic sense line heater tape, installing an inoperative ring, and coiling and stowing the electrical wire to the circuit breaker of the pneumatic sense line heater tape. This AD also provides for an optional inspection, which, if accomplished, constitutes terminating action for deactivation of the pneumatic sense line heater tape. This action is prompted by a report indicating that, while an airplane was on the ground, fuel was found leaking from the fuel feed pipe of the number 2 engine due to inadequate clearance between the fuel feed pipe and the pneumatic sense line heater tape. The actions specified by this AD are intended to detect and correct such inadequate clearance, which could result in a hole in the fuel feed pipe caused by electrical arcing, and consequent fuel leakage and possible ignition of the fuel vapors.
98-09-02: This amendment supersedes an existing airworthiness directive (AD), applicable to McDonnell Douglas Helicopter Systems (MDHS) Model 369 (YOH-6A), 369A (OH-6A), 369D, 369E, 369F, 369FF, 369H, 369HE, 369HM, and 369HS helicopters, that currently requires replacing overrunning clutch outer races (outer races) having certain heat treatment numbers. This amendment requires replacing all outer races with airworthy outer races, regardless of the heat treatment number, and is applicable to a particular model helicopter that was not included in the existing AD (Model 500N helicopters). This amendment is prompted by several reports of failed clutch races having heat treatment numbers other than the ones addressed in the earlier AD. The actions specified by this AD are intended to prevent failure of the overrunning clutch assembly outer race, which could result in loss of engine drive to the rotor system and a subsequent forced landing.
2012-18-16: We are adopting a new airworthiness directive (AD) for certain The Cessna Aircraft Company Model 750 airplanes. This AD was prompted by reports of direct current (DC) generator overvoltage events. This AD requires replacing the auxiliary power unit (APU) generator control unit (GCU). We are issuing this AD to prevent DC generator overvoltage events, which could result in smoke in the cockpit and loss of avionics and electrical systems.
2012-18-08: We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model SA330F, SA330G, SA330J, AS332C, AS332L, AS332L1, and AS332L2 helicopters to require cleaning, inspecting, and lubricating each tangential gearbox (gearbox) and adjusting, as necessary, the fuel shut-off control lever. This AD was prompted by the jamming of one of two fuel shut-off control levers because of solidified grease in the gearbox. A companion gearbox had extensive corrosion. In case of an emergency, pilots may need to use the control levers to shut off fuel going into the engine and to shut off the helicopter's electrical power system. The jamming of the levers prevents the shut off of the engine fuel and prevents the parallel- mounted micro switches from switching off the electrical power system. These actions are intended to prevent the jamming of the control levers, which could prevent shut-off of the engine fuel and electrical power system during an emergency shutdown.
2010-11-05: We are adopting a new airworthiness directive (AD) for certain AVOX Systems and B/E Aerospace oxygen cylinders, as installed on various 14 CFR part 23 or CAR 3 airplanes. This AD requires you to inspect for and remove substandard oxygen cylinders from the airplane. This AD was prompted by the reported rupture of a high-pressure gaseous oxygen cylinder, which had insufficient strength characteristics due to improper heat treatment. We are issuing this AD to prevent an oxygen cylinder from rupturing, which, depending on the location, could result in structural damage and rapid decompression of the airplane, damage to adjacent essential flight equipment, deprivation of the necessary oxygen supply for the flightcrew, and injury to cabin occupants or other support personnel.
2012-19-02: We are superseding an existing airworthiness directive (AD) for all Airbus Model A330-243, -341, -342 and -343 airplanes. That AD currently requires modifying certain cowl assemblies of the left- and right-hand thrust reversers. This new AD requires removing certain C- duct assemblies of the left- and right-hand thrust reversers from service at certain designated life limits, and also adds airplanes to the applicability. This AD was prompted by new life limits on certain thrust reverser C-duct assemblies. We are issuing this AD to prevent fatigue cracking of the hinges integrated into the 12 o'clock beam of the thrust reversers, which could result in separation of a thrust reverser from the airplane, and consequent reduced controllability of the airplane.
74-10-09: 74-10-09 BOEING: Amendment 39-1838 as amended by Amendment 39-2825. Applies to Boeing Model 707-100 series, -100B series and -200 series airplanes certificated in all categories. \n\tCompliance required as indicated. To detect cracks in the upper wing splice plate and upper rib cap at wing station 360, accomplish the following: \n\tUnless X-Ray or low frequency eddy current inspected within the last 300 flights, X-Ray or low frequency eddy current inspect the upper wing surface splice plate and rib cap at wing station 360 within the next 25 flights after the effective date of this AD, on airplanes with more than 24,000 flights, or within the next 50 flights after the effective date of this AD, on airplanes with more than 17,000 flights in accordance with instructions in Boeing Alert Service Bulletin No. 3160 dated April 19, 1974, or later FAA approved revisions, or in a manner approved by the Chief, Engineering and Manufacturing Branch, FAA, Northwest Region. If cracks are found, repair prior to further flight in accordance with Part VII or VIII or install external doubler in accordance with Part IX of Boeing Service Bulletin No. 2576, Revision 2, or later approved revisions or in a manner approved by the Chief, Engineering and Manufacturing Branch, FAA Northwest Region. \n\tThe Manufacturer's specifications and procedures identified and described in this directive are incorporated herein and made a part hereof pursuant to 5 U.S.C. 552(a)(1). All persons affected by this directive who have not already received these documents may obtain copies upon request to The Boeing Company, P.O. Box 3707, Seattle, Washington 98124. These documents may also be examined at FAA Northwest Region, Boeing Field, Seattle, Washington. \n\n\tAmendment 39-1838 became effective on May 10, 1974. \n\tThis amendment 39-2825 becomes effective February 21, 1977.
98-08-25: This amendment supersedes Airworthiness Directive (AD) 96-12-08 on certain Twin Commander Aircraft Corporation (Twin Commander) 500, 680, 690, and 695 series airplanes, which currently requires replacing the nose landing gear (NLG) drag link bolt with one that has been manufactured with the proper heat-treatment. This action will retain the requirements of AD 96-12-08, add an additional model and additional serial numbers to the applicability section of the AD, and require replacing bolt part number (P/N) ED10055 with bolt P/N 750076-1 on certain Models 690D and 695A airplanes. This action is prompted by a defective manufacture of a certain lot of drag link bolts used in the NLG. The actions specified by this AD are intended to prevent the NLG from collapsing caused by a failed drag link bolt, which could result in loss of control of the airplane during landing operations.
2012-18-09: We are adopting a new airworthiness directive (AD) for the Bell Helicopter Textron Canada Limited (BHTC) Model 407 helicopters. This AD requires you to replace tailboom-attachment hardware (attachment hardware), and perform initial and recurring determinations of the torque on the nuts of the tailboom-attachment bolts (bolts) at all four attachment locations. This AD was prompted by a review of the tailboom-attachment installation, which revealed that the torque value of the bolts specified in the BHTC Model 407 Maintenance Manual and applied during manufacturing was incorrect and exceeded the torque range recommended for the bolts. The actions required by this AD are intended to prevent an over-torque of a bolt, bolt failure, loss of the tailboom, and subsequent loss of control of the helicopter.
2010-11-15: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: The Civil Aviation Authority of the United Kingdom (UK) has informed EASA that significant quantities of Halon 1211 gas, determined to be outside the required specification, have been supplied to the aviation industry for use in fire extinguishing equipment. Halon 1211 (BCF) is used in portable fire extinguishers, usually fitted or stowed in aircraft passenger cabins and flight decks. EASA published Safety Information Bulletin (SIB) 2009-39 on 23 October 2009 to make the aviation community aware of this safety concern. The results of the ongoing investigation have now established that LyonTech Engineering Ltd, a UK-based company, has supplied further consignments of Halon 1211 (BCF) to L'Hotellier that do not meet the required specification. This Halon 1211 has subsequently been used to fill certain P/N 863520-00 portable fire extinguishers that are now likely to be installed in or carried on certain TBM700 aeroplanes. The contaminated nature of this gas, when used against a fire, may provide reduced fire suppression, endangering the safety of the aeroplane and its occupants. In addition, extinguisher activation may lead to release of toxic fumes, possibly causing injury to aeroplane occupants. We are issuing this AD to require actions to correct the unsafe condition on these products.