Results
2018-01-11: We are adopting a new airworthiness directive (AD) for certain Airbus Model A319-115 and A319-133 airplanes. This AD requires contacting the FAA to obtain instructions for addressing the unsafe condition on these products, and doing the actions specified in those instructions. This AD was prompted by a fire during a flight, in the vicinity of the gaseous oxygen system (GOS) for passengers. We are issuing this AD to address the unsafe condition on these products.
2002-21-07: This amendment adopts a new airworthiness directive (AD) for the specified Sikorsky Aircraft Corporation (Sikorsky) model helicopters that requires removing and inspecting each main rotor spindle attachment bolt (bolt) to ensure that the correct bolts are installed. This amendment is prompted by the discovery of improper bolts installed on a helicopter during its production. The actions specified by this AD are intended to detect installation of incorrect bolts, which could result in reduced hub or bolt fatigue life, separation of the main rotor blade at the spindle attachment, and subsequent loss of control of the helicopter.
2025-09-10: The FAA is adopting a new airworthiness directive (AD) for certain Leonardo S.p.A. Model A109E, A109S, and AW109SP helicopters. This AD was prompted by reports of incorrect installation of the motor (MTR) cables and the bonding braids connected to the engine fire extinguisher bottles. This AD requires inspecting the cables and bonding braids installation and, depending on the results, accomplishing corrective action, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2011-05-04: We are superseding an existing airworthiness directive (AD) for the products listed above. That AD currently requires sealing the fasteners on the front and rear spars inside the left and right main fuel tanks and on the rear spar and lower panel of the center fuel tank. That AD also requires inspections of the wire bundle support installations to verify if certain clamps are installed and if Teflon sleeving covers the wire bundles inside the left and right equipment cooling system bays, on the left and right rear spars, and on the left and right front spars; and corrective actions if necessary. This new AD also requires sealing the additional fasteners on the rear spar inside the left and right main fuel tanks. This AD was prompted by a fuel system review conducted by the manufacturer. We have received reports from the manufacturer that additional fasteners in the main fuel tanks must be sealed for lightning strike protection. We are issuing this AD to detect and correct improper wire bundle support installation and sleeving and to prevent improperly sealed fasteners in the main and center fuel tanks from becoming an ignition source, in the event of a fault current or lightning strike, which could result in a fuel tank explosion and consequent loss of the airplane.
2002-21-05: This amendment adopts a new airworthiness directive (AD) that applies to certain REVO, Incorporated (REVO) Models Lake LA-4, Lake LA- 4A, Lake LA-4P, Lake LA-4-200, and Lake Model 250 airplanes. This AD requires you to inspect the upper and lower wing spar doublers and angles for cracks at a certain time after the incorporation of Modification Kit B-79 or FAA-approved equivalent, replace any cracked wing spar doubler or angle, and report the results of the inspection to the Federal Aviation Administration (FAA). The kit modification consists of installing a doubler kit to give the spar an adequate fatigue life. This AD is the result of an incident of a crack found at the most outboard wing attachment fitting hole on one of the affected airplanes with the modification incorporated. The actions specified by this AD are intended to prevent wing spar failure caused by cracks in the wing spar doublers or angles, which could result in the wing separating from the airplane with consequent loss of control.
2024-01-02: The FAA is adopting a new airworthiness directive (AD) for all Lockheed Martin Corporation/Lockheed Martin Aeronautics Company Model 382, 382B, 382E, 382F, 382G, and 382J airplanes; and Model C-130A, HP- C-130A, EC-130Q, 282-44A-05 (C-130B), C-130B, and C-130H airplanes. This AD was prompted by the determination that certain aft fuselage sloping longerons may have been exposed to excessively hot forming temperatures for excessive amounts of time, which will reduce the mechanical properties of the longerons and affect their static strength. This AD requires, for certain airplanes, a records review to determine if a conductivity check has been performed on the longerons and to determine if the check was measured at least every four inches. This AD also requires, for certain airplanes, an inspection and applicable repairs. This AD also prohibits installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
2002-21-02: This amendment adopts a new airworthiness directive (AD) that applies to certain Cirrus Design Corporation (Cirrus) Model SR20 and SR22 airplanes. This AD requires you to replace the self-locking retaining nut on the roll and yaw trim cartridges with a new self- locking retaining nut with a higher axial load capability. This AD is the result of a report that, during a production flight test, the self- locking retaining nut on the yaw trim cartridge came off. The actions specified by this AD are intended to prevent loss of the self-locking retaining nut on the roll and yaw trim cartridges during flight, which could result in jamming of the corresponding flight control system. Such jamming could lead to loss of control of the airplane.
95-15-07: This amendment supersedes an existing airworthiness directive (AD), applicable to British Aerospace Model BAC 1-11 200 and 400 series airplanes, that currently requires structural inspections and repairs or replacements, as necessary. This amendment requires additional inspections of certain Structural Significant Items (SSI) and expansion of the inspection area for certain other SSI's. This amendment is prompted by the results of a structural integrity audit, which indicated that in order to maintain the structural integrity of these airplanes as they approach or exceed the manufacturer's original fatigue design life goal, certain SSI's need to be inspected. The actions specified by this AD are intended to ensure continuing structural integrity of these airplanes.
2023-26-03: The FAA is adopting a new airworthiness directive (AD) for certain WACO Classic Aircraft Corporation Model 2T-1A-2 airplanes. This AD was prompted by reports of multiple types of cracks at the leading edge former ribs and trailing edge former ribs in the upper wing center section. This AD requires installing maneuver restriction placards in the front and rear cockpits, inspecting the leading and trailing edge former ribs for cracking, replacing any cracked ribs, modifying the upper wing center section assembly, and removing the maneuver restriction placards after completing the modification. The FAA is issuing this AD to address the unsafe condition on these products.
2011-05-06: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: Service experience has shown that fracture of the timing chain has occurred due to chain wear. This condition, if not corrected, could lead to in-flight cases of engine shutdown. We are issuing this AD to prevent engine in-flight shutdown leading to loss of control of the airplane by requiring life limits for the timing chain.