Results
76-02-01: 76-02-01 CONSOLIDATED AERONAUTICS: Amendment 39-2494. Applies to all Model LA-4 and Model LA-4-200 airplanes equipped with STC SA876EA auxiliary fuel tanks. Compliance required, as indicated, by the effective date of this Amendment. To prevent engine power interruption resulting from water contamination of the fuel system due to water entering the auxiliary fuel tank sumps, accomplish the following: Install the following placard adjacent to the auxiliary tank fuel transfer switches: "WARNING" "Auxiliary tank fuel transfer prohibited unless auxiliary tank sumps are drained free of water after each water operation." This amendment becomes effective January 30, 1976.
98-02-05: This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 98-02-05, which was sent previously to all known U.S. owners and operators of Cessna Aircraft Company (Cessna) Model 172R airplanes. This AD requires de-activating the cabin heating system until the engine exhaust muffler can be replaced, and fabricating and installing a placard within the pilot s clear view, using 1/8-inch letters with the following words: "CABIN HEATER INOPERATIVE." Inadequate or failed weldments that are leaking exhaust gas (including carbon monoxide) from the muffler into the airplane s cabin and cockpit area prompted this action. The actions specified by this AD are intended to prevent carbon monoxide gas from entering the airplane s cabin heating system and cabin, which, if not corrected, could result in passenger and pilot injury with consequent loss of control of the airplane.
2012-02-01: We are adopting a new airworthiness directive (AD) for Pratt & Whitney (PW) PW2037, PW2037(M), and PW2040 turbofan engines with certain fan blades with a cutback leading edge, installed. This AD was prompted by reports from PW that fan blade leading edge erosion can result in a fan thrust deterioration mode (FTDM) condition, a condition that cannot be detected by the crew, and that reduces the engine's capability of producing required thrust. This AD requires initial and repetitive maintenance to the leading edge of cutback fan blades or applying performance decrements as specified in the Airplane Flight Manual. [[Page 16140]] We are issuing this AD to correct undetectable fan thrust deterioration on these PW products.
2012-05-04: The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 767 airplanes. This AD requires an inspection of the number 2 windows to \n\n((Page 16148)) \n\ndetermine whether the link arms are in the over-center position, and modifying the link arms of the number 2 windows in the flight compartment if necessary. This AD also requires the inspection, and modification if necessary, for airplanes that replace a modified assembly with an unmodified assembly. This AD results from reports of the number 2 windows opening during takeoff roll, which has resulted in aborted takeoffs. We are issuing this AD to prevent the opening of the number 2 windows during takeoff roll, which could adversely affect the flightcrew's ability to perform critical takeoff communication and result in an aborted takeoff or an unscheduled landing.
97-22-07: This amendment supersedes an existing airworthiness directive (AD), applicable to certain Boeing Model 737 series airplanes, that currently requires repetitive inspections to detect cracking of the lower skin at the lower row of fasteners in the lap joints of the fuselage, and repair of any cracking detected. This amendment requires that the inspections be accomplished at more frequent intervals. This amendment also adds a requirement for modification of the fuselage lap joints at certain locations, which constitutes terminating action for repetitive inspections of modified areas. This amendment is prompted by reports of numerous fatigue cracks in the lower skin of the fuselage lap joints at the lower row of fasteners. The actions specified in this AD are intended to prevent such fatigue cracking, which could result in sudden decompression of the airplane.
97-22-05: This amendment adopts a new airworthiness directive applicable to certain McDonnell Douglas Model DC-9 series airplanes and C-9 (military) series airplanes, that requires modification of the emergency internal release system of the tailcone and the accessory compartment. This amendment is prompted by a report that, due to failure of the tailcone release system, the tailcone did not deploy on an airplane during an emergency evacuation. The actions specified by this AD are intended to ensure that the emergency internal release system of the tailcone performs its intended function in the event of an emergency evacuation. The actions also are intended to prevent people on board the airplane from striking their heads on exposed metal frames in the tailcone area, which could cause injury and delay or impede their evacuation during an emergency.
2012-04-15: We are superseding an existing airworthiness directive (AD) for all Pratt & Whitney (PW) JT9D series turbofan engines. That AD currently requires revisions to the Airworthiness Limitations Section (ALS) of the manufacturer's Instructions for Continued Airworthiness (ICA) to include required enhanced inspection of selected critical life-limited parts at each piece-part opportunity. This new AD requires additional revisions to the JT9D series engines ALS sections of the manufacturer's ICA. This AD was prompted by the need to require enhanced inspection of selected critical life-limited parts of JT9D series engines. We are issuing this AD to prevent critical life-limited rotating engine part failure, which could result in an uncontained engine failure and damage to the airplane.
91-22-51: 91-22-51 BOEING: Amendment 39-8129. Docket 91-NM-214-AD. Final Rule of Telegraphic AD T91-22-51. \n\n\tApplicability: Model 757 series airplanes, line numbers 140 through 335, certificated in any category. \n\n\tCompliance: Required as indicated, unless previously accomplished. \n\n\tTo prevent the separation of the trailing edge wedges from the airplane, accomplish the following: \n\n\t(a)\tPerform a close detailed visual inspection of the trailing edge wedges of slats 1 through 4 and 7 through 10, for delamination and physical damage in accordance with Boeing Alert Service Bulletin 757-57A0045, dated October 16, 1991, at the times specified below: \n\n\t\t(1)\tFor airplanes that have accumulated 5,000 or more flight hours as of the effective date of this AD: Within the next 10 calendar days after the effective date of this AD, and thereafter at intervals not to exceed 300 flight hours. \n\n\t\t(2)\tFor airplanes that have accumulated less than 5,000 flight hours as of the effective date of this AD: Within the next 300 flight hours after the effective date of this AD, and thereafter at intervals not to exceed 300 flight hours. \n\n\t(b)\tWithin the next 300 flight hours after the effective date of this AD, perform a "coin-tap" inspection of the trailing edge wedges of slats 1 through 4 and 7 through 10 for delamination and physical damage, in accordance with Boeing Alert Service Bulletin 757- 57A0045, dated October 16, 1991, Repeat this inspection at intervals not to exceed 1,500 flight hours. \n\n\t(c)\tIf delamination and/or physical damage are found as a result of the inspections required by paragraph (a) or (b) of this AD, prior to further flight, repair in accordance with an FAA-approved procedure or replace with new parts. If a repair is accomplished or if new parts are installed, the inspections required by paragraphs (a) and (b) of this AD must be continued. \n\n\t(d)\tAn alternative method of compliance or adjustment of the compliance time, which provides an acceptable level of safety, may be used when approved by the Manager, Seattle Aircraft Certification Office (ACO), FAA, Transport Airplane Directorate. \n\n\tNOTE: The request should be forwarded through an FAA Principal Maintenance Inspector, who may concur or comment and then send it to the Manager, Seattle ACO. \n\n\t(e)\tSpecial flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate airplanes to a base in order to comply with the requirements of this AD. \n\n\t(f)\tThe inspections required by this AD shall be done in accordance with Boeing Alert Service Bulletin 757-57A0045, dated October 16, 1991. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR Part 51. Copies may be obtained from Boeing Commercial Airplane Group, P.O. Box 3707, Seattle, Washington 98124-2207. Copies may be inspected at the FAA, Transport Airplane Directorate, 1601 Lind Avenue S.W., Renton, Washington; or at the Office of the Federal Register, 1100 L Street N.W., Room 8401, Washington, D.C. \n\n\t(g)\tThis amendment (39-8129, AD 91-22-51) becomes effective on January 24, 1992, to all persons except those persons to whom it was made immediately effective by telegraphic AD T91-22-51, issued October 17, 1991, which contained the requirements of this amendment.
97-22-02: This amendment adopts a new airworthiness directive (AD) that applies to Pilatus Britten-Norman Ltd. (PBN) BN-2, BN-2A, BN-2B, and BN-2T series airplanes. This action requires modifying the upper engine mounting brackets on the wing front spar as terminating action for the repetitive inspections that were required in AD 84-23-06. AD 84-23-06 is being revised in a separate action, deleting the Pilatus BN-2, BN-2A, BN-2B, and BN-2T series airplanes from its applicability. This AD is prompted by several reports of cracks in the upper engine mounting brackets and a new terminating action to eliminate the repetitive inspections for Pilatus BN-2, BN-2A, BN-2B, and BN-2T series airplanes. The actions specified by this AD are intended to prevent the failure of the upper engine mounting brackets on the wing mounted engines, which could possibly cause structural failure of the airplane.
76-17-05: 76-17-05 LOCKHEED-CALIFORNIA: Amendment 39-2704. Applies to Lockheed L- 1011-385 Series airplanes certificated in all categories. Compliance required as indicated, unless already accomplished. To prevent fires which may be ignited by damaged electrical wires, accomplish the following: (a) Within the next 300 hours time in service after the effective date of this AD. (1) Inspect the No. 2 generator feeder cables located in the 1519938-103 ECS duct area on the left side of the No. 2 engine S-duct, between FS-1956 and FS-1975, at approximately WL-310, for a minimum clearance of one-half inch between the cables and the closest part of the ECS duct insulated cover in accordance with Lockheed Alert Service Bulletin 093-24-A058, dated June 3, 1976 or later FAA-approved revision. (2) If the clearance is less than one-half inch, adjust to provide adequate clearance before further flight in accordance with Lockheed Service Bulletin 093-24-A058, dated June 3, 1976 or later FAA-approved revision. (b) Within the next 300 hours time in service after the effective date of this AD. (1) Inspect the electrical wire bundles just aft of the lower left hand side of FS-1860 bulkhead which are routed adjacent to the APU bleed air duct, for proper clamping and condition of insulation. If insulation damage is found, check closely for wire damage. (2) If damage to insulation or wires is found, before further flight, repair in accordance with FAA-approved maintenance procedures. (c) Within the next 300 hours time in service after the effective date of this AD. (1) Inspect the left hand and right hand horizontal stabilizer servo units by applying 3,000 PSI hydraulic pressure to each hydraulic system and observing for signs of hydraulic fluid misting or spraying type of leakage, or examine left hand and right hand horizontal servo unit transfer tube areas for signs of external leakage immediately after hydraulic systems have been shut down.(2) If hydraulic leaks are found, before further flight, repair in accordance with FAA-approved maintenance procedures. (d) It is requested that a written report on the results of the inspections required by paragraphs (b) and (c), either positive or negative, be forwarded to: Chief, Aircraft Engineering Division, Federal Aviation Administration, Western Region, P. O. Box 92007, World Way Postal Center, Los Angeles, CA 90009. (Reporting approved by the Office of Management and Budget under OMB 04- RO174). (e) Equivalent procedures may be approved by the Chief, Aircraft Engineering Division, FAA Western Region. (f) Special flight permits may be issued per FAR's 21.197 and 21.199, to authorize flights to a base for accomplishment of the inspections required by this AD. This amendment becomes effective September 2, 1976.