Results
2008-03-15: We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: A non-respect of the pilot door adjustment procedure could have damaged the stop fitting and could result in a consequent depressurization of the airplane. We are issuing this AD to require actions to correct the unsafe condition on these products. DATES: This AD becomes effective March 11, 2008. On March 11, 2008, the Director of the Federal Register approved the incorporation by reference of EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-131, Amendment 1, dated June 2007, listed in this AD. As of March 23, 2007 (72 FR 7559, February 16, 2007), the Director of the Federal Register approved the incorporation by reference of EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-131, dated July 2005, listed in this AD.
2023-11-11: The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 747-8 and 747-8F series airplanes. This AD was prompted by reports of cracks in stringers, common to the end fittings, forward and aft of the pressure bulkhead at station (STA) 2360 at multiple stringer locations. This AD requires repetitive inspections of stringer sidewalls and certain stringer assemblies, common to the end fittings, forward and aft of the pressure bulkhead at STA 2360 for any crack, and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.
2022-12-09: The FAA is superseding Airworthiness Directive (AD) 2017-15-06 for all British Aerospace Regional Aircraft Model HP.137 Jetstream Mk.1, Jetstream Series 200 and 3101, and Jetstream Model 3201 airplanes. AD 2017-15-06 required repetitively inspecting the main landing gear (MLG) for cracks and, if cracks were found, replacing the MLG with an airworthy part. Since the FAA issued AD 2017-15-06, the Civil Aviation Authority (CAA) of the United Kingdom (UK) superseded the mandatory continuing airworthiness information (MCAI) issued by the European Aviation Safety Agency (EASA) to correct an unsafe condition on these products. This AD retains the initial inspection and the calculation of hours time-in-service to flight cycle actions required by AD 2017-15-06, but decreases the repetitive inspection interval time from 1,200 flight cycles to 900 flight cycles. The FAA is issuing this AD to address the unsafe condition on these products.
2008-03-12: The FAA is superseding an existing airworthiness directive (AD), which applies to certain McDonnell Douglas airplanes. The existing AD currently requires an initial general visual or dye penetrant inspection, repetitive dye penetrant inspections, and replacement, as necessary, of the rudder pedal bracket. The existing AD also currently requires, for certain airplanes, replacing the rudder pedal bracket assemblies with new, improved parts, which would terminate the repetitive inspections. For certain airplanes, this new AD requires initial inspection at a reduced threshold, removes an inspection option, and lengthens the repetitive inspection intervals. This AD results from reports of failures of the captain's rudder pedal brackets before reaching the initial inspection threshold identified in the existing AD. We are issuing this AD to prevent failure of the rudder pedal bracket assembly, which could result in the loss of rudder and braking control at either the captain's or first officer's position.
2023-13-15: The FAA is superseding Airworthiness Directive (AD) 2023-03- 06, which applied to all Bombardier, Inc., Model BD-700-1A10 and BD- 700-1A11 airplanes. AD 2023-03-06 required revising the existing airplane flight manual (AFM) to incorporate limitations to mitigate identified hazards when in the presence of interference from wireless broadband operations in the 3.7-3.98 GHz frequency band (5G C-Band) as identified by Notices to Air Missions (NOTAMs). Since the FAA issued AD 2023-03-06, the FAA determined that additional limitations are needed due to the continued deployment of new 5G C-Band stations whose signals are expected to cover most of the contiguous United States at transmission frequencies between 3.7-3.98 GHz. This AD requires revising the limitations section of the existing AFM to incorporate limitations prohibiting dispatch under a certain master minimum equipment list (MMEL) item. The FAA is issuing this AD to address the unsafe condition on these products.
2008-03-07: We are adopting a new airworthiness directive (AD) for Eurocopter Model AS 332 L2 helicopters. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority to identify and correct an unsafe condition on an aviation product. The European Aviation Safety Agency (EASA), the Technical Agent of France, with which we have a bilateral agreement, states in the MCAI: A borescope inspection during scheduled maintenance revealed wear on the internal skin of a Life Raft Inflation Cylinder, P/N 41918001, that had been installed on a Eurocopter AS 332 L2 helicopter. The plunger tube end is fitted with a metal end-fitting that presses against the internal surface of the cylinder due to its installation horizontally aboard the aircraft. Vibrations generated by helicopter operation are therefore causing such wear, which may result in a drop of internal pressure of the cylinder. This internal damage, if not corrected, could lead to functional failure of the cylinder, making the life raft inflation no longer possible. This AD requires actions that are intended to address the failure of a life raft to inflate during an emergency landing on water (ditching), which could result in loss of the crew and passengers.
2023-12-26: The FAA is superseding Airworthiness Directive (AD) 2021-24- 04, which applied to certain Bell Helicopter Textron Canada Limited (type certificate previously held by Bell Helicopter Textron Canada Limited) Model 505 helicopters. AD 2021-24-04 required revising the existing Rotorcraft Flight Manual (RFM) for your helicopter. Since the FAA issued AD 2021-24-04, Bell Textron Canada Limited revised the RFM to incorporate more restrictive operating limitations. This AD is prompted by the determination that the existing altitude limitations were not valid for certain fuel types and that revising the existing RFM for your helicopter to align with the limitations of the Safran Helicopter Engines, S.A. Model ARRIUS 2R engine is necessary. This AD requires revising the existing RFM for your helicopter, as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2007-26-51: This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2007-26-51, which was sent previously to all known U.S. owners and operators of Eurocopter Deutschland GmbH (Eurocopter) Model EC135 helicopters by individual letters. This AD requires, within 5 hours time-in-service (TIS), inspecting the tail rotor control rod (control rod) and adjoining ball pivot and replacing any unairworthy parts before further flight. This amendment is prompted by a report of a fatal accident involving the failure of a control rod. The actions specified by this AD are intended to prevent failure of a control rod and subsequent loss of control of the helicopter.
2023-12-06: The FAA is superseding Airworthiness Directive (AD) 2020-07- 13, which applied to certain Bombardier, Inc., Model BD-100-1A10 airplanes. AD 2020-07-13 required revising the existing airplane flight manual (AFM) to provide the flightcrew with new warnings for ''Autoflight'' and ''Engine Failure in Climb During ALTS CAP.'' This AD requires revising the existing AFM to provide the flightcrew with new warnings for ''Autoflight'' and ''Engine Failure in Climb During (V) ALTS CAP or (V) ALTV CAP.'' This AD was prompted by a revision to the procedures to ensure that all applicable altitude capture modes utilized and annunciated in the affected fleet are included and to more clearly denote these altitude capture modes. The FAA is issuing this AD to address the unsafe condition on these products.
2008-02-19: The FAA is adopting a new airworthiness directive (AD) for Honeywell International Inc. (Honeywell) TFE731-2C, -3B, -3BR, -3C, - 3CR, -3D, -3DR, -4R, -5AR, -5BR, -5R, -20R, -20AR, -20BR, -40, -40AR, - 40R, and -60 series turbofan engines. This AD requires removal from service of certain high pressure (HP) turbine rotor assemblies with part numbers (P/Ns) 3075772-1 and 3060841-1 using a drawdown schedule, and returning them to Honeywell for curvic root radius inspection. This AD results from the manufacturer's report that some HP turbine rotor discs received improperly machined radii in the root of the forward and aft curvic teeth during manufacture. We are issuing this AD to prevent uncontained failure of the HP turbine rotor assembly, which could result in damage to the airplane.