Results
84-15-05: 84-15-05 BELL HELICOPTER TEXTRON, INC.: Amendment 39-4891. Applies to all Bell Helicopter Textron, Inc., Model 214ST helicopters certified in all categories equipped with main rotor collective lever assembly P/N 214-010-474-109 or -113. Compliance is required as indicated, unless already accomplished. To prevent failure of the collective lever assembly, remove and replace the lever assembly prior to accumulating 1,250 hours time in service. For helicopters that have accumulated more than 1,250 hours time in service on the lever assembly, remove and replace the lever assembly within the next 50 hours time in service or by September 1, 1984, whichever comes first. This amendment becomes effective August 3, 1984.
2010-21-16: We are superseding an existing airworthiness directive (AD) for the products listed above. That AD currently requires modifying the auxiliary hydraulic power system (including doing all applicable related investigative and corrective actions). This new AD requires these same actions, using corrected service information. This AD was prompted by fuel system reviews conducted by the manufacturer, as well as reports of electrically shorted wires in the right wheel well and evidence of arcing on the auxiliary hydraulic pump power cables, which are routed within the tire burst area. We are issuing this AD to prevent electrically shorted wires or arcing at the auxiliary hydraulic pump power cables, which could result in a fire in the wheel well. We are also issuing this AD to reduce the potential of an ignition source adjacent to the fuel tanks, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
2010-21-12: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: * * * * * Recently, a brake fire was reported which was caused by a ruptured brake piston. The fire was quickly extinguished but caused damage to the paint and hydraulic/electrical harness and its components. Detailed investigation showed that a hydraulic lock must have been present close to the affected brake creating enough internal pressure to rupture the piston. The most probable scenario for the hydraulic lock is a loosened (not necessarily disconnected) brake QD [quick-disconnect] coupling. Further investigation of the service experience files at Fokker Services showed that more brake fires have occurred on aeroplanes in a pre-mod SBF100-32-127 configuration. * * * * * The unsafe condition is loss of braking capability and possible brake fires, which could reduce the ability of the flightcrew to safely land the airplane. We are issuing this AD to require actions to correct the unsafe condition on these products.
87-11-02: 87-11-02 THE DEHAVILLAND AIRCRAFT COMPANY OF CANADA, A DIVISION OF BOEING OF CANADA, LTD.: Amendment 39-5625. Applies to all Model DHC-7 series airplanes, certificated in any category. Compliance is required as indicated, unless already accomplished. To assure that flames will not penetrate the rear cargo compartment liner to the fuselage primary structure, accomplish the following: A. Within the next 6 months after the effective date of this AD, modify the DHC-7 rear cargo liner in accordance with DH Modification No. 7/2499, as detailed in DeHavilland Service Bulletin No. 7-25-49, Revision A, dated July 11, 1986, or later revisions approved by the Manager, New York Certification Office, FAA, New England Region. B. Alternate means of compliance which provide an acceptable level of safety may be used when approved by the Manager, New York Aircraft Certification Office, FAA, New England Region. C. Special flight permits may be issued in accordance with FAR 21.197and 21.199 to operate airplanes to a base in order to comply with the requirements of this AD. All persons affected by this directive who have not already received the appropriate service documents from the manufacturer may obtain copies upon request to The de Havilland Aircraft Company of Canada, A Division of Boeing of Canada, Ltd., Garratt Boulevard, Downsview, Ontario M3K 1Y5, Canada. These documents may be examined at the FAA, Northwest Mountain Region, 17900 Pacific Highway South, Seattle, Washington, or FAA, New England Region, New York Aircraft Certification Office, 181 South Franklin Avenue, Room 202, Valley Stream, New York. This amendment becomes effective June 21, 1987.
87-22-05: 87-22-05 BRITISH AEROSPACE: Amendment 39-5751. Applies to all Model H.S. 748 series airplanes with a large freight door, certificated in any category. Compliance required within the next 90 days after the effective date of this AD, unless previously accomplished. To prevent inadvertent opening of the freight door in flight, accomplish the following: A. Inspect the large freight door shoot bolt lever, barometric (pressure lock) lever, bellows assembly, dry air cartridge and microswitches for damage, distortion and/or wear in accordance with British Aerospace Service Bulletin 52/129, dated May 1986. If any damage, distortion and/or wear is discovered as a result of the inspection required by this paragraph, prior to further flight, adjust, repair, or replace the affected components, in accordance with British Aerospace Service Bulletin 52/129, dated May 1986. B. Install a placard to indicate that the aircraft must be depressurized before opening its large freight door, in accordance with British Aerospace Service Bulletin 11/7, dated December 1, 1986. C. An alternate means of compliance or adjustment of the compliance time, which provides an acceptable level of safety, may be used when approved by the Manager, Standardization Branch, ANM-113, FAA, Northwest Mountain Region. D. Special flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate airplanes to a base for the accomplishment of inspections and/or modifications required by this AD. All persons affected by this directive who have not already received the appropriate service information from the manufacturer may obtain copies upon request to British Aerospace, Librarian for Service Bulletins, P.O. Box 17414, Dulles International Airport, Washington, D.C. 20041. This information may be examined at the FAA, Northwest Mountain Region, 17900 Pacific Highway South, Seattle, Washington, or at the Seattle Aircraft Certification Office, 9010 East Marginal Way South, Seattle, Washington. This amendment becomes effective November 13, 1987.
2010-21-19: We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires replacing aluminum fire extinguisher discharge tubes with new, improved tubes; checking the fire extinguisher container for certain serial numbers; replacing fire extinguisher containers that have affected serial numbers; inspecting the pressure indicator on certain fire extinguisher containers for discrepancies; and performing corrective action if necessary. This AD was prompted by a report of accidental discharge of a fire extinguisher container and damage to an aluminum discharge tube. Investigation revealed that following the discharge an inaccurate pressure indication, due to the indicator dial being incorrectly staked, showed that the container was fully charged. We are issuing this AD to prevent inaccurate pressure readings and subsequent damage to the discharge tubes during operation, which could result in failure of the fire extinguisher system and an uncontained fire inan emergency situation.
2010-21-17: The FAA is adopting a new airworthiness directive (AD) for Pratt & Whitney (PW) JT8D-9, -9A, -11, -15, -17, and -17R turbofan engines. This AD requires overhauling fan blade leading edges at the first shop visit after 4,000 cycles-in-service (CIS) since the last total fan blade overhaul was performed. This AD results from reports of failed fan blades. We are issuing this AD to prevent high-cycle fatigue cracking at the blade root, which could result in uncontained failures of first stage fan blades and damage to the airplane.
92-23-01: 92-23-01 BELL HELICOPTER TEXTRON, INC. (BHTI); CALIFORNIA DEPARTMENT OF FORESTRY; GARLICK HELICOPTERS; HAWKINS AND POWERS AVIATION, INC; INTERNATIONAL HELICOPTERS, INC.; PILOT PERSONNEL INTERNATIONAL, INC.; SOUTHERN AERO CORPORATION; AND SOUTHWEST FLORIDA AVIATION: Amendment 39-8401. Docket No. 90-ASW-42. Applicability: All BHTI Model 204B, 205A, 205A-1, 205B, and 212 helicopters, certificated in any category, and military Model UH-1B, UH-1F, and UH-1H helicopters, certificated in the restricted category. Compliance: Required as indicated, unless accomplished previously. To prevent separation of the main rotor pillow blocks from the hub assembly as a result of bolt cracking, which could result in loss of the main rotor and subsequent loss of control of the helicopter, accomplish the following: (a) Within the next 300 hours time in service after the effective date of this AD; or at the next main rotor hub retention strap change; or at the next hub assembly overhaul; whichever occurs first, remove the four bolts, part number (P/N) 204-011-171-003, joining the two pillow blocks to the main rotor yoke assembly. Reinstall the pillow blocks using new (zero time) bolts, P/N 204-011-171-003; nuts, P/N EB080 or 42FLW-820; and washers, P/N 140-007-33S28-3 as follows: (1) Coat the shank of the bolts with corrosion prevention compound, such as MIL-C-16173 Grade 1, and dry torque the bolts and nuts 65 to 79 foot-pounds. Retorque nuts within 15 to 30 hours time in service after the initial installation. If the torque has reduced below the minimum value of 65 foot-pounds, repeat the torque check at intervals of 15 to 30 hours time in service until the torque remains at or above 65-foot pounds or until the torque check has been accomplished four times. If during the fourth check the torque has reduced below 65 foot-pounds, remove and replace the bolts, washers, and nuts and repeat the torque check procedure of this paragraph. (2) After initialinstallation or retorque, apply sealant, such as BHTI P/N 299-947-107 TYIII CL7, to the four bolt heads, washers, nuts and yoke mating surfaces to prevent moisture from entering the pillow block retention area. (b) Thereafter, remove the bolts and associated hardware from the pillow block and replace with new bolts, washers, and nuts as described in paragraph (a) of this AD at each hub assembly overhaul, at each change of the main rotor hub retention strap, or whenever the bolts are removed for any reason. NOTE: Bell Helicopter Textron, Inc., Alert Service Bulletins 204-90-27, Revision A; 205-90-38, Revision A; and 212-90-62, Revision A, all dated October 11, 1990, pertain to this AD. A copy of the service bulletins may be obtained from Bell Helicopter Textron, Inc., P.O. Box 482, Fort Worth, Texas 76101. (c) Rework or repair of the bolts, P/N 204-011-171-003; nuts, P/N EB080 or 42FLW-820; and washers, P/N 140-007-33S28-3, is not authorized. (d) An alternative method ofcompliance or adjustment of the compliance times, which provides an acceptable level of safety, may be used when approved by the Manager, Rotorcraft Certification Office, ASW-170, Federal Aviation Administration, Fort Worth, Texas 76193-0170. Operators shall submit their request through an FAA Principal Maintenance Inspector, who may concur or comment and then send it to the Manager, Rotorcraft Certification Office. NOTE: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Manager, Rotorcraft Certification Office. (e) Special flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate the helicopter to a location where the requirements of this AD can be accomplished. (f) This amendment becomes effective April 23, 1993.
2010-21-05: We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: During ground manoeuvring, prolonged operation with either engine in the restricted range between 82% and 90% RPM [revolutions per minute] will result in damage [e.g., cracking of the blade or hub] to the propeller assembly that could eventually result in the release of a propeller blade. * * * EASA [European Aviation Safety Agency] AD 2007-0268 [which corresponds to FAA AD 2008-13-02, amendment 39-15565] was issued to require the installation of a Propeller Warning Placard and implementation of a corresponding Aircraft Flight Manual (AFM) limitation instructing the flight crew to taxi with the condition lever at FLIGHT in order to minimisethe time spent by the engines in the restricted range. BAE Systems has now developed a Propeller Speed Warning System * * *. * * * * * A released propeller blade could result in engine failure and loss of control of the airplane. We are issuing this AD to require actions to correct the unsafe condition on these products.
91-03-10: 91-03-10 CASA: Amendment 39-6883. Docket No. 90-NM-17-AD. Applicability: Model C-212 series airplanes, certificated in any category. Compliance: Required within 60 days after the effective date of this AD, unless previously accomplished. To prevent reduced controllability of the airplane, accomplish the following: A. Modify the propeller speed and pitch control system so that the control cannot be moved into reverse thrust while in flight, and so that the propeller pitch settings cannot be adjusted for ground operation while in flight, in accordance with CASA Service Bulletin 212-76-07, dated July 27, 1990, or in a manner approved by the Manager, Standardization Branch, ANM-113, FAA, Transport Airplane Directorate. B. An alternate means of compliance or adjustment of the compliance time, which provides an acceptable level of safety, may be used when approved by the Manager, Standardization Branch, ANM-113, FAA, Transport Airplane Directorate. NOTE: The request should be submitted directly to the Manager, Standardization Branch, ANM- 113, and a copy sent to the cognizant FAA Principal Inspector (PI). The PI will then forward comments or concurrence to the Manager, Standardization Branch, ANM-113. C. Special flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate airplanes to a base in order to comply with the requirements of this AD. All persons affected by this directive who have not already received the appropriate service documents from the manufacturer may obtain copies upon request to Construcciones Aeronauticas S.A., Getafe, Madrid, Spain. These documents may be examined at the FAA, Northwest Mountain Region, Transport Airplane Directorate, 1601 Lind Avenue S.W., Renton, Washington. Airworthiness Directive 91-03-10 supersedes AD 90-04-11. Amendment 39-6508. This amendment (39-6883, AD 91-03-10) becomes effective on March 11, 1991.