Results
2006-10-02: The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 747 airplanes. This AD requires the following actions for the drive mechanism of the horizontal stabilizer: Repetitive detailed inspections for discrepancies and loose ball bearings; repetitive lubrication of the ballnut and ballscrew; repetitive measurements of the freeplay between the ballnut and the ballscrew; and corrective action if necessary. This AD results from a report of extensive corrosion of a ballscrew in the drive mechanism of the horizontal stabilizer on a similar airplane model. We are issuing this AD to prevent an undetected failure of the primary load path for the ballscrew in the horizontal stabilizer and subsequent wear and failure of the secondary load path, which could lead to loss of control of the horizontal stabilizer and consequent loss of control of the airplane.
2006-09-05: The FAA is adopting a new airworthiness directive (AD) for all Airbus Model A310-200 and -300 series airplanes. This AD requires doing repetitive rotating probe inspections for any crack of the rear spar internal angle and the left and right sides of the tee fitting, and doing related investigative/corrective actions if necessary. This AD also requires modifying the holes in the internal angle and tee fitting by cold expansion. This AD results from full-scale fatigue tests, which revealed cracks in the lower rear spar internal angle, and tee fitting. We are issuing this AD to detect and correct fatigue cracks of the rear spar internal angle and tee fitting, which could lead to the rupture of the internal angle, tee fitting, and rear spar, and consequent reduced structural integrity of the wings.
2004-03-15 R1: The FAA is revising an existing airworthiness directive (AD) that applies to certain Bombardier Model DHC-8-102, -103, -106, -201, - 202, -301, -311, and -315 airplanes. That AD currently requires performing a one-time inspection to detect chafing of electrical wires in the cable trough below the cabin floor; repairing, if necessary; installing additional tie-mounts and tie-wraps; applying sealant to rivet heads; and modifying electrical wires in certain sections. We issued that AD to prevent chafing of electrical wires. This new AD, for certain airplanes, eliminates the requirement to modify electrical wires in certain sections. This AD results from a report indicating that the modification of electrical wires does not need to be done on certain airplanes subject to the existing AD. We are issuing this AD to prevent chafing of electrical wires, which could result in an uncommanded shutdown of an engine during flight. DATES: The effective date of this AD is March 19, 2004.On March 19, 2004 (69 FR 7111, February 13, 2004), the Director of the Federal Register approved the incorporation by reference of Bombardier Service Bulletin 8-53-80, Revision "A", dated July 25, 2000. On October 27, 1998 (63 FR 50501, September 22, 1998) the Director of the Federal Register approved the incorporation by reference of Bombardier Service Bulletin S.B. 8-53-66, dated March 27, 1998.
2006-09-08: The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD requires modifying the wiring on an alternating current (AC) service bus contactor that is located in the avionics bay. This AD results from incidents of short circuit failures of certain AC contactors located in the avionics bay. We are issuing this AD to prevent short circuit failures of certain AC contactors, which could result in arcing and consequent smoke or fire.
2006-08-11: We are adopting a new airworthiness directive (AD) for all Pilatus Aircraft Ltd. Models PC-12 and PC-12/45 airplanes equipped with certain crew seat bucket assemblies with and without a backrest recline system. This AD requires you to replace the backrest tubes on these crew seat bucket assemblies at a specified time and adds a life limit for these backrest tubes. This AD results from mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Switzerland. We are issuing this AD to prevent cracks in the backrest tubes of certain crew seat bucket assemblies, which could result in failure of the seat system. This failure could lead to the pilot and co-pilot's reduced ability to control the airplane. This failure could also affect the proper function of the seat restrain system in the case of an emergency landing.
2006-08-06: This amendment adopts a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model SA-360C, SA-365C, SA-365C1, and SA-365C2 helicopters. This action requires inspecting the main gearbox (MGB) base plate for a crack and replacing the MGB if a crack is found. This amendment is prompted by the discovery of a crack in a MGB base plate. The actions specified in this AD are intended to detect a crack in a MGB base plate and prevent failure of one of the MGB attachment points to the frame, which could result in severe vibration and subsequent loss of control of the helicopter.
2006-07-21: The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 757 airplanes. This AD requires repetitive inspections for corrosion and cracking of the midspar fittings in the nacelle struts, and corrective actions if necessary. This AD also provides an optional terminating action for the repetitive inspections. This AD results from reports of corrosion and cracking on midspar fittings on the nacelle struts of several Boeing Model 757 airplanes. We are issuing this AD to detect and correct cracking in the midspar fittings of the nacelle struts, consequent reduced structural integrity of the struts, and possible separation of an engine and strut from the airplane.
2006-07-14: The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 767-200, -300, and -300F series airplanes. This AD requires verifying the part and serial numbers of certain main landing gear (MLG) bogie beam pivot pins; replacing those pivot pins with new or overhauled pivot pins if necessary; and ultimately replacing all pivot pins with new, improved pivot pins. This AD also requires repetitive lubrications and inspections of the pivot pin, and related investigative and corrective actions if necessary. This AD results from reports indicating that numerous fractures of the MLG bogie beam pivot pin have been found and that some pivot pins may have had improper rework during manufacture. We are issuing this AD to prevent fracture of the MLG bogie beam pivot pin, which could lead to possible loss of the MLG truck during takeoff or landing and consequent loss of control of the airplane.
2006-07-06: The FAA adopts a new airworthiness directive (AD) for certain Cirrus Design Corporation (CDC) Models SR20 and SR22 airplanes. This AD requires you to inspect the fuel line and wire bundles for any chafing damage; replace any damaged fuel line and repair any damaged wires or sheathing of the wire harness if any chafing damage is found; and install (to prevent any chafing damage to the fuel line and wire bundles) the forward loop clamp, fuel line shield, aft loop clamp, and anti-chafe tubing. This AD results from reports of fuel line leaks resulting from wire chafing on the fuel lines. We are issuing this AD to detect, correct, and prevent damage to the fuel line and wire bundles, which could result in fuel leaks. This failure could lead to unsafe fuel vapor within the cockpit and possible fire.
2006-05-11 R1: The FAA is revising an existing airworthiness directive (AD), which applies to certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. The existing AD currently requires revising the airworthiness limitations section of the Instructions for Continued Airworthiness of the maintenance requirements manual (MRM) by incorporating procedures for repetitive functional tests of the pilot input lever of the pitch feel simulator (PFS) units. That AD also requires new repetitive functional tests of the pilot input lever of the PFS unit, and corrective actions if necessary; and after initiating the new tests, requires removal of the existing procedures for the repetitive functional tests from the MRM. This AD retains the requirements of the existing AD and further clarifies the requirements of the AD. This AD results from a report that the shear pin located in the input lever of two PFS units failed due to fatigue. We are issuing this AD to prevent undetected failure of the shear pin of both PFS units simultaneously, which could result in loss of pitch feel forces and consequent reduced control of the airplane. DATES: The effective date of this AD is March 27, 2006. On March 27, 2006 (71 FR 12277, March 10, 2006), the Director of the Federal Register approved the incorporation by reference of a certain publication. On February 13, 2004 (69 FR 4234, January 29, 2004), the Director of the Federal Register approved the incorporation by reference of Bombardier Temporary Revision 2B-1784, dated October 24, 2003, to the CL-600-2B19 Canadair Regional Jet Maintenance Requirements Manual, Part 2, Appendix B, "Airworthiness Limitations.'' We must receive any comments on this AD by May 30, 2006.