Aircraft-logs.com

Results
2023-17-06: The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model CL-600-1A11 (600), CL-600-2A12 (601), and CL-600-2B16 (601-3A, 601-3R, and 604 Variants) airplanes. This AD was prompted by an uncommanded flap extension accompanied by a flaps fail caution message during climb. This AD requires initial and repetitive operational tests of the flap control system. The FAA is issuing this AD to address the unsafe condition on these products.
2011-03-12: We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires a detailed inspection for proper sealant of the left and right pylon firewall structures, and corrective actions if necessary. This AD results from reports of missing sealant on the left and right pylon firewall structures. We are issuing this AD to detect and correct missing sealant on the left and right pylon firewall structures, which, in the event of an engine fire, could result in flames penetrating the seams in the firewall between the engine and the aft fuselage, and a subsequent uncontrolled fire in the aft fuselage.
2002-14-22: This amendment adopts a new airworthiness directive (AD) that applies to all Pilatus Aircraft Ltd. (Pilatus) Models PC-12 and PC-12/45 airplanes. This AD requires you to inspect the left and right main landing gear (MLG) assemblies for bolts with a serial number (S/N) beginning with the letters "AT" and numbers 299 or lower and replace each bolt with a bolt that does not have a S/N with both the letters "AT" and a number of 299 or lower. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Switzerland. The actions specified by this AD are intended to detect and replace defective MLG assembly bolts that have an improper cadmium plating, which could cause hydrogen embrittlement and bolt failure. Such failure could lead to MLG collapse during landing.
2023-18-04: The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) Model CF6-80E1A2, CF6-80E1A3, CF6-80E1A4, and CF6-80E1A4/B engines. This AD was prompted by a manufacturer investigation that revealed that a certain forward outer seal and certain high-pressure turbine rotor (HPTR) stage 1 disks and rotating seals were manufactured from material suspected to contain iron inclusion, which may cause reduced material properties and a lower fatigue life capability. This AD requires the replacement of the affected forward outer seal, HPTR stage 1 disks, and rotating seals. The FAA is issuing this AD to address the unsafe condition on these products.
94-11-11: This amendment supersedes an existing airworthiness directive (AD), applicable to Pratt & Whitney Canada PW100 series turboprop engines, that currently requires rework or replacement of the intercompressor case (ICC), and replacement of the low pressure rotor speed (NL) sensor port sealing tube and the external air tube connecting the P2.5/P3 switching valve to the rear inlet case. This amendment additionally requires installation of an airflow deflector bracket nozzle assembly, or modification of the No. 5 bearing pressure air system. Finally, this action requires installation of a No. 5 bearing vent tube assembly and allows extension of the compliance interval for reworking or replacing the ICC. This amendment is prompted by the development of additional hardware that will further reduce the risk of internal oil fires in the ICC. The actions specified by this AD are intended to prevent fire in the engine ICC and nacelle cavities, inflight engine shutdown, and aircraft damage.
2002-14-19: This amendment adopts a new airworthiness directive (AD) that applies to certain Rockwell Collins, Inc. (Rockwell Collins) ADC-85, ADC-85A, ADC-850D, and ADC-850F air data computers that are installed on airplanes. This AD requires you to replace any affected air data computer (ADC) with one that has a reprogrammed and tested central processing unit (CPU) circuit card and circuit card assembly. This AD is the result of a flight test that showed that these ADC's could display an unwarranted ADC flag in response to the airplane's "Normal/Alternate Air" static source selection capability. The actions specified by this AD are intended to prevent an unwarranted display of the ADC flag when switching static air sources. This could cause the flight crew to react to this incorrect flight information and possibly result in an unsafe operating condition.
2002-14-02: This amendment adopts a new airworthiness directive (AD) that is applicable to certain Boeing Model 767-300 series airplanes equipped with Rolls Royce RB211-524H series engines. This action requires re-routing a certain wire bundle containing control wiring for the thrust reverser actuation system. This action is necessary to ensure that control wiring for the thrust reverser actuation system is adequately separated. Inadequately separated wiring could allow a single failure to result in uncommanded deployment of a thrust reverser and consequent reduced controllability of the airplane. This action is intended to address the identified unsafe condition.
2023-17-05: The FAA is adopting a new airworthiness directive (AD) for all Schempp-Hirth Flugzeugbau GmbH (Schempp-Hirth) Model Ventus-2a and Ventus-2b gliders. This AD is prompted by reports of the uncommanded extraction of the airbrakes on one or both wings, possibly resulting in reduced control of the glider. This AD requires repetitively inspecting airbrake bell cranks and airbrake drive funnels for cracking, repetitively inspecting the clearance of the airbrake control system, and taking corrective action as necessary. This AD also requires modifying the airbrake system, which is terminating action for the repetitive inspections. The FAA is issuing this AD to address the unsafe condition on these products.
2002-14-18: This amendment adopts a new airworthiness directive (AD) that applies to all Glaser-Dirks Flugzeugbau GmbH (DG Flugzeugbau) Models DG-400 and DG-800A sailplanes. This AD requires you to inspect the rear plate of the propeller mount for marks and/or cracks and replace if necessary. This AD also requires you to inspect the mounting blocks for cracks and replace if necessary. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Germany. The actions specified by this AD are intended to detect and correct cracks in the propeller mount plate and mounting blocks, which could result in reduced structural integrity of the propeller mounting structure. This could lead to a hazardous flight condition or loss of control of the sailplane.
2023-17-11: The FAA is adopting a new airworthiness directive (AD) for all Rolls-Royce Deutschland Ltd & Co KG (RRD) Model BR700-715A1-30, BR700- 715B1-30, and BR700-715C1-30 engines. This AD was prompted by reports of malformed scallop edge geometry and surface conditions at the front flange scallops of affected low-pressure compressor (LPC) booster rotors. This AD requires repetitive fluorescent penetrant inspections (FPIs) of the front flange scallops of the LPC booster rotor for any cracks, replacement or repair of the LPC booster rotor if necessary and, as an optional terminating action to the repetitive FPIs, a visual inspection for malformed scallop edge geometry and malformed surface conditions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference (IBR). The FAA is issuing this AD to address the unsafe condition on these products.