Results
94-09-05: This amendment adopts a new airworthiness directive (AD), applicable to certain de Havilland Model DHC-7 series airplanes, that requires a one-time inspection to assess the adequacy of the clearance between various adapter plates and seal retaining angles on the fuselage side access panel, and modification of both the forward and rear seal retention angles. This amendment is prompted by reports of incidents involving corrosion and fatigue cracking in commuter-class airplanes that are approaching or have exceeded their economic design goal. The actions specified by this AD are intended to prevent degradation of the structural capabilities of the affected airplanes.
2007-24-10: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) provided by the European Aviation Safety Agency (EASA) to identify and correct an unsafe condition on Turbomeca Arriel 2S1 and 2S2 turboshaft engines. The MCAI states the following: During assembly of a new HP/LP fuel pump, the drain screw on the fuel filter unit failed when it was tightened to the torque value specified in the assembly schedule (12 Nm). Investigation of the screw showed that it was fully conformed to its specification, in terms of both dimensions and material. The mechanical calculations show, however, that a torque value of 12 Nm is too high for this screw, exceeding the elastic limit of the material. Failure of the affected screw could cause a fuel leak, resulting in an engine flame-out or engine fire. We are issuing this AD to prevent a fuel leak as a result of a ruptured fuel filter drain screw that could lead to engine flame-out or an engine fire.
94-08-06: This amendment adopts a new airworthiness directive (AD), applicable to Pratt & Whitney JT9D-7R4 series turbofan engines, that requires initial and repetitive fan blade leading edge inspections, and either installation of fan blade sets with modified fan blade shrouds or rework of the fan blade shrouds as a terminating action to the inspections. This amendment is prompted by reports of flutter-induced fan blade fractures. The actions specified by this AD are intended to prevent fan blade fracture and uncontained engine failure, resulting in possible damage to the aircraft.
2001-10-07: This amendment adopts a new airworthiness directive (AD), that is applicable to General Electric Co. (GE) CF6-80C2 turbofan engines with certain stage 1 high pressure turbine (HPT) rotor disks installed. This amendment requires initial and repetitive inspections of certain HPT rotor disks for cracks in the bottom of the dovetail slot. This amendment is prompted by a report of an uncontained failure of an engine during a high-power ground run for maintenance. The actions specified by this AD are intended to detect cracks in the bottoms of the dovetail slots that could propagate to failure of the disk and cause an uncontained engine failure.
2019-25-18: The FAA is adopting a new airworthiness directive (AD) for all Bombardier, Inc., Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This AD was prompted by a report of a wing stall (wing drop/ uncommanded roll) during landing flare, due to ice on the wing leading edges that was not detected by the anti-ice system. This AD requires revising the existing airplane flight manual (AFM) to include a limitation and normal operating procedure for the wing anti-ice system. The FAA is issuing this AD to address the unsafe condition on these products.
94-09-11: This amendment adopts a new airworthiness directive (AD) that is applicable to certain Raytheon Corporate Jets Model BAe 125-1000A and Hawker 1000 series airplanes. This action requires inspections of the thrust reverser system for integrity, and correction of any discrepancy found. This amendment is prompted by a report that there is a possibility of failure of the drive links (or attachments) on the thrust reversers of these airplanes due to the single link design concept of the thrust reverser link and lock system. This condition, if not corrected, could result in inadvertent deployment of a thrust reverser during flight. The actions specified in this AD are intended to prevent a significant reduction in the controllability of the airplane due to an in-flight deployment of a thrust reverser. Comments for inclusion in the Rules Docket must be received on or before June 28, 1994.
77-13-05: 77-13-05 CANADAIR: Amendment 39-2930. Applies to CL-215 Airplanes, Serial Numbers 1001 through 1040 and 1046, certificated in all categories. Compliance required prior to U.S. airworthiness certification, unless already accomplished: (a) Inspect the right hand canopy sill for missing rivets forward and aft of bulkhead 234.5 as indicated in Figures 1 and 3 of the Canadair Information Circular (S.I.C.) No. 129-CL- 215 dated May 12, 1976, or an approved equivalent inspection. (b) If rivets have been omitted forward of the bulkhead, between stations 223 and 229, install three NAS 1103-4 bolts with MS2104L3 Nuts and Strip Washer as shown in Figure 2 of the S.I.C. or an approved equivalent alteration. (c) If rivet spacing aft of the bulkhead is greater than 1.25 inch install intermediate rivets as indicated in Figure 3 of the S.I.C. or an approved equivalent alteration. (d) Equivalent inspections, alterations or parts must be approved by Chief, Engineering and Manufacturing Branch, FAA, Eastern Region. This Amendment becomes effective June 29, 1977.
2007-24-14: The FAA is adopting a new airworthiness directive (AD) for Hartzell Propeller Inc. Model HC-E5N-3( ), HC-E5N-3( )(L), and HC-E5B- 5( ) propellers. This AD requires a onetime eddy current inspection of the propeller hub mounting bolt holes and replacement of the propeller hub if cracked. This AD results from the discovery of a five-bladed propeller hub with a large crack on the mounting flange of the hub. We are issuing this AD to prevent propeller hub failure, blade separation, damage to the airplane, and possible loss of airplane control.
2019-23-04: The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 727 airplanes. This AD was prompted by the FAA's analysis of the Model 727 fuel system review conducted by the manufacturer. This AD requires modifying the fuel quantity indicating system (FQIS) to prevent development of an ignition source inside the body-mounted auxiliary fuel tanks due to electrical fault conditions. As an alternative to the modification, this AD allows deactivating the body-mounted auxiliary fuel tanks. The FAA is issuing this AD to address the unsafe condition on these products.
2007-24-03: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: It has been found the development of cracks in the forward fuselage right hand (RH) side skin during full-scale fatigue tests. Those cracks may quickly reach their critical length, reducing the aircraft structural integrity, with possible rapid decompression of the aircraft. We are issuing this AD to require actions to correct the unsafe condition on these products.