Results
2021-17-14: The FAA is adopting a new airworthiness directive (AD) for certain Gulfstream Aerospace LP Model Gulfstream G280 airplanes. This AD was prompted by a report that during full-scale fatigue testing, a crack was found in the area of the attachment of the wing rib 0 to the front spar. This AD requires non-destructive testing on the forward (front) spar vertical stiffener and rib 0 for any cracking, installation of a doubler to the forward (front) spar and rib 0 attachment, and repair if necessary, as specified in a Civil Aviation Authority of Israel (CAAI) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
71-17-09: 71-17-09 SCHWEIZER AIRCRAFT: Amdt. 39-1272. Applies to SGS 1-23H. Type Gliders. To prevent severe oscillations and vibrations resulting from excessively loose rudder fittings accomplish the following: (a) Within the next 25 hours time in service unless accomplished within the last 75 hours time in service and thereafter at intervals not to exceed 100 hours time in service, inspect the lower and upper rudder and fin hinges P/N 1A-107-2, P/N 23H704-16 & -17, P/N 1A-105-2 and P/N 23H705-21, to assure that neither the fore and aft nor the sidewards free-play exceeds five-thousandths (0.005) inches. (b) If free-play in excess of the limits set forth in paragraph (a) is found, replace hinges and their connecting bolts with parts of the same part number or with FAA approved equivalent parts; or incorporate a modification described in Schweizer Aircraft Corporation Service Bulletin No. 102-23-2 dated 29 June 1971 or an FAA approved equivalent modification. Equivalent partsor modifications must be approved by the Chief, Engineering and Manufacturing Branch, FAA, Eastern Region. (c) The compliance times may be increased by the Chief, Engineering and Manufacturing Branch, FAA, Eastern Region upon receipt of substantiating data submitted through an FAA Maintenance Inspector. This amendment becomes effective August 26, 1971.
98-11-20: This amendment adopts a new airworthiness directive (AD) that applies to certain Pilatus Aircraft Ltd. (Pilatus) Models PC-12 and PC-12/45 airplanes that incorporate an executive cabin layout. This AD requires modifying the lavatory wall and passenger seat configuration. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Switzerland. The actions specified by this AD are intended to prevent head injuries during an airplane crash because the lavatory wall and passenger seat configuration do not meet current head injury criteria regulations.
2004-09-01: This amendment adopts a new airworthiness directive (AD) that is applicable to certain Airbus Model A300 B4-600, B4-600R, C4 605R Variant F, and F4-600R (collectively called A300-600) series airplanes; and Model A310 series airplanes. This action requires a one-time inspection for damage of the integrated drive generator electrical harness and pyramid arm, and repair if necessary. This action is necessary to prevent electrical arcing within the engine pylon, which could result in loss of the relevant alternating current (AC) bus bar, reduced structural integrity of the engine pylon, and consequent loss of control of the airplane. This action is intended to address the identified unsafe condition.
98-11-12: This amendment adopts a new airworthiness directive (AD), applicable to certain de Havilland Model DHC-8-301, -311, -314, and -315 series airplanes, that requires installation of additional wiring and new electrical connectors for the lights in the forward end of the passenger overhead compartments. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by this AD are intended to prevent severe overheating of the electrical connectors for the lights in the forward end of the passenger overhead compartments, which could result in smoke and fire in the passenger cabin.
2021-18-09: The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 777 airplanes. This AD was prompted by a report that an operator found solid rivets with missing heads at the left buttock line 25 on the sloping pressure deck web. This AD requires doing a detailed inspection of the left- and right-side sloping pressure deck at certain stations for any damaged solid rivets, and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.
69-08-03: 69-08-03 VICKERS: Amdt. 39-747. Applies to Viscount Models 744, 745D, and 810 Series airplanes. Compliance required within the next 1000 hours' time in service after the effective date of this AD, unless already accomplished. To prevent discharge of power plant fire extinguishant into the wrong power plant due to incorrect assembly of power plant fire extinguisher bottles, install interference brackets and retaining cables to the detachable clip assemblies at the fire extinguishing bottle neck at the inner and outer nacelle mountings in accordance with British Aircraft Corporation Modification Bulletin D.3218 dated July 14, 1968 (700 Series) or Modification Bulletin FG.2094 dated July 14, 1968 (800/810 Series) or later ARB-approved issues or an equivalent approved by the Chief, Aircraft Certification Staff, FAA, Europe, Africa and Middle East Region. This amendment becomes effective May 11, 1969.
2021-18-03: The FAA is superseding Airworthiness Directive (AD) 2020-26- 02, which applied to certain Yabora Industria Aeronautica S.A. (type certificate previously held by Embraer S.A.) Model ERJ 190-400 airplanes. AD 2020-26-02 required amending the existing airplane flight manual (AFM) to incorporate a new limitation and revise certain normal procedures. This AD retains those requirements and also requires upgrading the electronic engine control (EEC) software, as specified in an Agencia Nacional de Aviacao Civil (ANAC) AD, which is incorporated by reference. This AD was prompted by a report of an in-flight shutdown (IFSD) due in part to failure in the low-pressure compressor (LPC) rotor 1 during operation in high altitude at high thrust settings, and by the development of updated EEC software, which would \n\n((Page 51598)) \n\nterminate the requirement to amend the existing AFM. The FAA is issuing this AD to address the unsafe condition on these products.
2004-09-03: The FAA adopts a new airworthiness directive (AD) for certain HPH s. r. o. (HPH) Models Glasflugel 304CZ, 304CZ-17, and 304C sailplanes. This AD requires you to inspect to determine the airbrake handle attachment rivet material. This AD also requires you to replace any non-steel rivet with a steel rivet. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for the Czech Republic. We are issuing this AD to prevent the airbrake handle from becoming loose, which could result in failure of the airbrake control. This failure could lead to loss of control of the sailplane.
2021-18-04: The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A318, A319, A320, and A321 series airplanes. This AD was prompted by reports of low halon concentration in the forward and aft cargo compartments due to air leakage through cargo door seals, and the certification of improved cargo door seals. This AD requires repetitive cleaning and greasing of affected cargo door seals; replacing the forward, aft, and bulk cargo compartment door seals with new seals; and installing a placard on the forward, aft, and cargo compartment doors; and for certain airplanes, implementing an operational limitation for certain routes, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2021-18-01: The FAA is adopting a new airworthiness directive (AD) for B-N Group Ltd. Models BN-2, BN-2A, BN-2A-2, BN-2A-3, BN-2A-6, BN-2A-8, BN- 2A-9, BN-2A-20, BN-2A-21, BN-2A-26, BN-2A-27, BN-2B-20, BN-2B-21, BN- 2B-26, BN-2B-27, BN-2T, and BN-2T-4R airplanes. This AD was prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI identifies the unsafe condition as failure of the rudder final drive rod because of cracks in the region of the taper pins. This AD requires repetitively inspecting the rudder final drive rod assembly and replacing the rudder final drive assembly, if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
98-16-18: This amendment adopts a new airworthiness directive (AD) that is applicable to certain Learjet Model 60 airplanes. This action requires repetitive measurements of the brake wear dimension between the housing subassembly and the pressure plate that is adjacent to the top pistons of the brake assembly; and follow-on corrective actions, if necessary. This amendment is prompted by reports of abnormal (uneven) brake wear. The actions specified in this AD are intended to detect and repair an abnormal brake wear condition, which could result in loss of brake effectiveness and cause the airplane to leave the runway surface.
2011-08-07: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: In January 2009 a Trent 895 powered Boeing 777-200 aircraft experienced release of a low pressure (LP) compressor blade which failed due to fatigue cracking in the root section of the blade. The released blade (undercut root standard) had received a part life processing to apply a compression layer to the blade root (Service Bulletin SB 72-D672--Introduction of Laser Shock Peening (LSP)) and also a part life upgrade to the retention feature lubrication system. Investigation has revealed that the effectiveness of this upgraded blade root lubrication coating system may be reduced dependant on the extent of previous running with the earlier standard, leadingto increased blade root stress levels. In the specific case of the released blade, a review of its in-service modification history has shown that it operated for a relatively high number of flight cycles prior to the compression layer processing and the new retention feature lubrication system. A review of the Engine Health Monitoring data has also identified it operated at high N1 speeds compared to the Trent 800 fleet average N1 speeds. The combination of these factors has resulted in increased fatigue life usage which is considered to have led to crack initiation and propagation prior to reaching the blades declared life limit. A review of all in-service undercut/LSP standard Trent 800 LP compressor blades has identified specific blades that carry a similar increased susceptibility to cracking. This AD is issued to mitigate the risk of possible multiple fan blades failure affecting those blades identified as described above which could lead to high energy non contained debris from the engine. We are issuing this AD to prevent LP compressor blades from failing due to blade root cracks, which could lead to uncontained engine failure and damage to the airplane.
97-25-11 R1: This amendment revises an existing airworthiness directive (AD), applicable to certain Bombardier Model CL-600-2B16 series airplanes, that currently requires disabling the remote fuel/defuel panel in the cockpit; and provides for an optional modification of the remote fuel/defuel panel, which would terminate the requirement to disable the panel. This amendment reduces the applicability of the existing AD. This amendment is prompted by reports of in-flight failure of the panel that resulted when a circuit breaker on a battery bus opened due to insufficient current flow capacity. The actions specified in this AD are intended to prevent the circuit breakers from opening during flight, which could result in irreversible loss of engine indicating and fuel quantity systems in the cockpit.
2011-23-04: We are superseding an existing airworthiness directive (AD) for the engines identified above. That AD currently requires initial and repetitive visual inspections of the forward engine mount assembly side links for cracks, stripping and reapplying the Sermetel W coating on the side links at every exposure of the side link. This new AD requires those same inspections, stripping and reapplying the Sermetel W coating, and adds two part numbers [[Page 68635]] to the applicability. This AD was prompted by a review of the inspection program, which revealed that GE had omitted two affected side link part numbers from the applicability. We are issuing this AD to prevent failure of the side links and possible engine separation from the airplane.
70-15-01: 70-15-01 SIKORSKY AIRCRAFT: Amdt. 39-1026. Applies to Sikorsky S-61A/L/N/R Type Helicopters Certificated In All Categories and Incorporating Torrington A18702 Series Cabin Heater Blower Assemblies. Compliance required within the next 25 hours' time of cabin heater operation after the effective date of this AD unless already accomplished. To prevent potential hazards associated with intermittent operation of the cabin heater blower, accomplish the following: (a) Comply with the Accomplishment Instructions (excluding paragraph D) of Sikorsky Service Bulletin No. 61B55-14 dated 1 April 1970, or later revision, or equivalent method both approved by the Chief, Engineering and Manufacturing Branch, FAA, Eastern Region. (b) Upon request with substantiation data submitted through an FAA maintenance inspector, the compliance time specified in this AD may be increased by the Chief, Engineering and Manufacturing Branch, FAA, Eastern Region. This amendment is effective July 22, 1970.
2021-19-01: The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited Model 206, 206A, 206A-1 (OH-58A), 206B, 206B-1, 206L, 206L-1, 206L-3, 206L-4, 222, 222B, 222U, 230, 407, 427, 429, and 430 helicopters. This AD was prompted by a report of a shoulder harness seat belt comfort clip (comfort clip) interfering with the seat belt inertia reel. This AD requires removing each comfort clip from service, inspecting the shoulder harness seat belt for any rip and abrasion, and removing any shoulder harness seat belt from service that has a rip or abrasion. The FAA is issuing this AD to address the unsafe condition on these products.
2021-17-15: The FAA is adopting a new airworthiness directive (AD) for Leonardo S.p.a. Model AB139 and AW139 helicopters with certain main rotor blades installed. This AD was prompted by a report of an in- flight loss of a main rotor blade (MRB) tip cap. This AD requires inspecting the MRB tip cap for disbonding. The FAA is issuing this AD to address the unsafe condition on these products.
2011-23-09: We are adopting a new airworthiness directive (AD) for Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 705), [[Page 68307]] and CL-600-2D24 (Regional Jet Series 900) airplanes. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: There have been two reported cases of failure of the MLG [main landing gear] piston axle, P/N [part number] 49203-3 or 49203-5, resulting from fretting between the inboard axle sleeve and axle thrust face, damage to the protective coating and consequent stress corrosion. In both cases, the MLG did not collapse. * * * * * The unsafe condition is failure of the MLG, which could adversely affect the airplane's safe landing. We are issuing this AD to require actions to correct the unsafe condition on these products.
72-06-01: 72-06-01 BRITISH AIRCRAFT CORPORATION: Amdt. 39-1406. Applies to Model BAC 1-11 200 and 400 series airplanes which do not have BAC Modification PM 4621 Part (b) incorporated on all flap sections. Compliance is required as indicated. To prevent failures of the flap forward inboard pick-up fitting assemblies (six per airplane), accomplish the following: (a) For flap sections with a pick-up fitting assembly with a spigot having P/N AB09- 1723 (pre-Mod. 4621) installed: (1) Remove the lower inboard access panel and visually inspect the pick-up fitting assembly for failure of the spigot in accordance with British Aircraft Corporation Model BAC 1-11 Alert Service Bulletin No. 57-A-PM 4621, Issue 2, dated July 27, 1970 or an FAA-approved equivalent as follows: (i) On the inboard (No. 1) flap sections, within the next 650 landings after the effective date of this AD, or before the accumulation of 7,500 landings on the pick-up fitting assembly spigot, whichever occurs later, and thereafter at intervals not to exceed 650 landings from the last inspection until the spigot is replaced in accordance with paragraph (a)(4)(ii), or the assembly is replaced in accordance with paragraph (a)(4)(iii). (ii) On the center (No. 2) and outboard (No. 3) flap sections, within the next 2,000 landings after the effective date of this AD, or before the accumulation of 7,500 landings on the pick-up assembly spigot, whichever occurs later, and thereafter at intervals not to exceed 2,000 landings from the last inspection until the spigot is replaced in accordance with paragraph (a)(4)(ii), or the assembly is replaced in accordance with paragraph (a)(iii). (2) If a failed spigot is found during an inspection required by paragraph (a)(1), before further flight comply with paragraph (a)(4). (3) Within the next 1,000 landings after the effective date of this AD or before the accumulation of 25,000 landings on the pick-up assembly spigot, whichever occurs later, comply with paragraph (a)(4). (4) Comply with either subparagraph (i), (ii), or (iii). (i) Replace an affected spigot with a serviceable spigot of the same part number and continue to inspect in accordance with paragraph (a) (1); or (ii) Replace an affected spigot with an improved spigot, P/N AB09- 3887 (BAC Modification PM 4621, Part (a) in accordance with British Aircraft Corporation Model BAC 1-11 Service Bulletin No. 57-PM 4621, Issue 1, dated May 18, 1970 or an FAA-approved equivalent and inspect in accordance with paragraph (b)(1); or (iii) Replace the assembly containing the affected spigot with a new assembly (BAC Modification PM 4621, Part (b)) in accordance with British Aircraft Corporation Model BAC 1-11 Service Bulletin No. 57-PM 4621, Issue 1, dated May 18, 1970 or an FAA- approved equivalent. (b) For flap sections with a pick-up fitting assembly with a spigot having P/N AB09- 3887 (post-Mod. 4621, Part (a)) installed: (1) Remove the lower inboard access panel and visually inspect the pick-up fitting assembly for failure of the spigot in accordance with British Aircraft Corporation Model BAC 1-11 Alert Service Bulletin No. 57-A-PM 4621, Issue 2, dated July 27, 1970 or an FAA-approved equivalent as follows: (i) On the inboard (No. 1) flap sections, within the next 650 landings after the effective date of this AD or before the accumulation of 20,000 landings on the pick-up fitting assembly spigot, whichever occurs later, and thereafter at intervals not to exceed 650 landings from the last inspection until the assembly is replaced in accordance with paragraph (b)(4)(ii). (ii) On the center (No. 2) and outboard (No. 3) flap sections, within the next 2,000 landings after the effective date of this AD or before the accumulation of 20,000 landings on the pick-up fitting assembly, whichever occurs later, and thereafter at intervals not to exceed 2,000 landings from the last inspection, until the assembly is replaced in accordance with paragraph (b)(4)(ii). (2) If a failed spigot is found during an inspection required by paragraph (b)(1), before further flight comply with paragraph (b)(4). (3) Within the next 1,000 landings after the effective date of this AD or before the accumulation of 30,000 landings on the pick-up assembly, whichever occurs later, comply with paragraph (b)(4). (4) Comply with either subparagraph (i) or (ii). (i) Replace an affected spigot with a serviceable spigot of the same part number and continue to inspect in accordance with paragraph (b)(1); or (ii) Replace the assembly containing the affected spigot with a new assembly (BAC Modification PM 4621, Part (b)) in accordance with British Aircraft Corporation Model BAC 1-11 Service Bulletin No. 57-PM 4621, Issue 1, dated May 18, 1970 or an FAA- approved equivalent. This amendment becomes effective April 6, 1972.
2021-17-12: The FAA is superseding Airworthiness Directive (AD) 2020-13-07 for all Rolls-Royce Deutschland Ltd & Co KG (RRD) Trent 1000-D2, Trent 1000-J2, and Trent 1000-K2 model turbofan engines with a certain part- numbered fuel pump installed. AD 2020-13-07 required removal and replacement of the fuel pump with a part eligible for installation. This AD was prompted by the manufacturer's investigation into an unexpected reduction in fuel pump performance in certain high life fuel pumps and subsequent determination that an additional part-numbered fuel pump is subject to the same unsafe condition. This AD requires new and reduced life limits for certain part-numbered fuel pumps, depending on the engine model the fuel pump is installed on. The FAA is issuing this AD to address the unsafe condition on these products.
2004-09-06: This amendment supersedes an existing airworthiness directive (AD), applicable to all Airbus Model A319, A320, and A321 series airplanes. That AD currently requires identification of the part number and serial number of the parking brake operated valve (PBOV); and, if necessary, inspection of the PBOV, including a functional check of the PBOV, and follow-on and corrective actions. That AD also provides for an optional terminating action for the requirements of that AD. This new action mandates the previously optional terminating action, which terminates the inspection requirements of the previous AD. The actions specified by this AD are intended to prevent leakage of hydraulic fluid from the PBOV, which could cause the loss of the parking brake accumulator, and render the alternate braking system and the parking/emergency braking system inoperative, as well as causing the loss of function of the yellow hydraulic system (which provides all or part of the hydraulics for the elevator, rudder, aileron, flaps, stabilizer, yaw damper, pitch and yaw feel systems and autopilot, and certain spoilers).
2021-16-04: The FAA is adopting a new airworthiness directive (AD) for all Leonardo S.p.a. Model AB412 and AB412 EP helicopters. This AD was prompted by a report of the failure of both inverters in-flight, leading to an autopilot disconnection. This AD requires a one-time inspection of the clearance between a certain protective grommet installed in the emergency bus interlock compartment and the cable assemblies passing through it, and depending on the finding, applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
77-13-06: 77-13-06 PILATUS AIRCRAFT LTD. AND FAIRCHILD HILLER: Amendment 39- 2928. Applies to Pilatus Model PC-6 airplanes (all variants) with serial numbers up through 743 and Fairchild Hiller Model PC-6 airplanes, serial numbers 2001 through 2019, 2021 through 2038, and 2040 through 2049, certificated in all categories. Compliance is required as indicated. To prevent a possible landing flap nose rib fatigue failure, accomplish the following: (a) Within the next 25 hours time in service after the effective date of this AD, unless already accomplished within the last 25 hours time in service, and, thereafter, at intervals not to exceed 100 hours time in service since the last inspection, visually inspect all the end ribs of the landing flaps for cracks in accordance with Pilatus Service Bulletin No. 124, paragraph 2.1, dated January 1976, or an FAA-approved equivalent. (b) If a crack is found during any inspection required by paragraph (a) of this AD, before further flight, repair the crack in accordance with paragraphs 2.1 and 2.2 of Pilatus Service Bulletin No. 124, dated January 1976, or an FAA-approved equivalent. (c) Within the next 1,000 hours time-in-service after the effective date of this AD, unless already accomplished, reinforce the landing flap nose end ribs in accordance with paragraph 2.3 of Pilatus Service Bulletin No. 124, dated January 1976, or an FAA-approved equivalent. (d) The repetitive inspections required by paragraph (a) of this AD may be discontinued after the reinforcement has been accomplished in accordance with paragraph (c) of this AD, and all cracks have been repaired in accordance with paragraph (b) of this AD. (Fairchild Hiller Service Bulletin PC-6-51-3 pertains to this same subject.) This amendment becomes effective July 25, 1977.
98-09-07: This amendment adopts a new airworthiness directive (AD), applicable to certain Fokker Model F27 Mark 100, 200, 300, 400, 500, 600, and 700 series airplanes, that requires a modification of the lapjoint below the chine line at certain fuselage stations. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by this AD are intended to prevent fatigue cracking in the lapjoint below the chine line at certain fuselage stations, which could result in reduced structural integrity of the fuselage.