Results
2007-24-07: The FAA is adopting a new airworthiness directive (AD) for a GE CF6-80C2B1 turbofan engine, serial number (SN) 690203, with fan disk, part number (P/N) 1703M78P11, SN RPMDA662, installed. This AD requires stripping of thermal spray coating, inspection of dovetail slots, and reapplication of thermal spray coating on certain stage 1 fan disks. This AD results from a report that a repair shop did not meet the process requirements when applying copper-nickel-indium (Cu- Ni-In) thermal coating to certain stage 1 fan disks. We are issuing this AD to prevent possible uncontained release of multiple fan blades, resulting in damage to the airplane.
2023-02-01: The FAA is adopting a new airworthiness directive (AD) for all Bombardier, Inc., Model BD-100-1A10 airplanes. This AD was prompted by an investigation that indicated that one of the springs in the pitch trim switch of the horizontal stabilizer had failed. The failure of the spring could result in the airplane pitching nose down when actually commanded nose up. This AD requires a verification of the serial numbers of certain pitch trim switches, and replacement of the affected pitch trim switches with new ones in the pilot and co-pilot control wheels. This AD would also prohibit the installation of affected parts. The FAA is issuing this AD to address the unsafe condition on these products.
2023-01-10: The FAA is adopting a new airworthiness directive (AD) for certain GE Aviation Czech s.r.o. (GEAC) M601E-11, M601E-11A, M601E- 11AS, M601E-11S, and M601F model turboprop engines. This AD was prompted by the exclusion of life limits for certain compressor cases and compressor drums from the airworthiness limitations section (ALS) of the engine maintenance manual (EMM). This AD was also prompted by certain compressor cases that, following rework, were improperly re- identified and the engine logbook entries were not completed. This AD requires recalculation of the consumed life for the affected compressor cases and compressor drums and, depending on the results of the recalculation, removal and replacement of the affected compressor case or compressor drum with a part eligible for installation. The FAA is issuing this AD to address the unsafe condition on these products.
2007-23-18: The FAA is superseding an existing airworthiness directive (AD) that applies to all Boeing Model 747-100B SUD, 747-300, 747-400, and 747-400D series airplanes; and Model 747-200B series airplanes having a stretched upper deck. The existing AD currently requires repetitively inspecting for cracking or discrepancies of the fasteners in the tension ties, shear webs, and frames at body stations 1120 through 1220, and performing related investigative and corrective actions if necessary. This new AD reduces the repetitive interval for certain inspections. This AD results from new reports of multiple severed adjacent tension ties, in addition to the previous reports of cracked and severed tension ties, broken fasteners, and cracks in the frame, shear web, and shear ties adjacent to tension ties for the upper deck. We are issuing this AD to detect and correct cracking of the tension ties, shear webs, and frames of the upper deck, which could result in rapid decompression and reduced structural integrity of the airplane. \n\n\nDATES: This AD becomes effective November 28, 2007. \n\n\tOn April 26, 2006 (71 FR 14367, March 22, 2006), the Director of the Federal Register approved the incorporation by reference of Boeing Alert Service Bulletin 747- 53A2507, dated April 21, 2005. \n\tWe must receive any comments on this AD by January 22, 2008.
2007-19-53: This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2007-19-53, which was sent previously to all known U.S. owners and operators of the specified Bell Helicopter Textron, Inc. (BHTI) model helicopters by individual letters. This AD requires replacing each affected tail rotor blade (blade) with an airworthy blade with a serial number not listed in the applicability of this AD. This AD is prompted by three incidents in which blade tip weights were slung from the blades during flight causing significant vibration. The actions specified by this AD are intended to prevent loss of a blade tip weight, loss of a blade, and subsequent loss of control of the helicopter.
2023-01-01: The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A318 series airplanes; Model A319-111, -112, -113, - 114, -115, -131, -132, and -133 airplanes; Model A320-211, -212, -214, -216, -231, -232, and -233 airplanes; and Model A321-111, -112, -131, - 211, -212, -213, -231, and -232 airplanes. This AD was prompted by a report of a nose landing gear (NLG) sliding tube rupture that led to a NLG collapse. This AD requires inspection of certain NLG and main landing gear (MLG) sliding tubes and applicable corrective actions and eventual replacement of all affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference (IBR). This AD also prohibits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
2023-01-04: The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350D, AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters. This AD was prompted by an occurrence reported where during an inspection of a tail rotor head (TRH) pitch change spider, excessive play and excessive wear were detected, due to an unwanted rotating motion. This AD requires for helicopters with certain part- numbered TRH spider pitch change units installed, inspecting for correct installation of the spider pitch change nut (nut); marking a 2 to 5 mm wide black paint index mark and repetitively inspecting the alignment of the marking; and additional inspections and corrective actions if necessary. This AD also allows an affected part to be installed on a helicopter if certain requirements of this AD are met. The FAA is issuing this AD to address the unsafe condition on these products.
2007-23-15: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: It has been found the occurrence of incorrect use of the self- locking nuts in bolts subject to rotational loads in bolted fittings of some assemblies of metallic components. Such event may result in disconnection of those fittings, which jeopardizes the structural integrity of the aircraft or its flight controls. Since this condition may occur in other airplanes of the same type and affects flight safety, a corrective action is required. Thus, sufficient reason exists to request compliance with this AD in the indicated time limit. We are issuing this AD to require actions to correct the unsafe condition on these products.
2020-25-03R1: The FAA is removing Airworthiness Directive (AD) 2020-25-03, which applied to all Airbus SAS Model A318, A319, A320, and A321 series airplanes. AD 2020-25-03 required repetitive checks of the pressure gauges to determine the amount of pressure on the inflation reservoir of each emergency escape slide/raft, and applicable corrective actions. AD 2020-25-03 also provided optional terminating action for the repetitive checks. The FAA issued AD 2020-25-03 to address insufficient reservoir pressure in an emergency escape slide/raft, which would prevent the deployment of the emergency escape slide/raft during an emergency, possibly resulting in injury to the occupants. The FAA has determined that AD 2020-25-03 is no longer necessary because the unsafe condition no longer exists. Accordingly, AD 2020-25-03 is removed.
2022-26-06: The FAA is adopting a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500- 1A11 airplanes. This AD was prompted by reports of flight control (horizontal stabilizer, rudder, and elevator) decals degrading and peeling (damage), reports of operators painting over these decals, and reports that procedures to replace these decals were inaccurate, potentially causing incorrect positioning of replacement decals. This AD requires inspecting the left and right horizontal stabilizer decals for visibility and damage; and for certain airplanes, inspecting the rudder and left and right elevator decals for visibility and damage; and doing applicable corrective actions; as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.