Results
2011-03-11: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: A recent Wide spread Fatigue Damage (WFD) calculation on A300- 600 aeroplanes has shown that a reinforcement of the upper fuselage circumferential joint at FR (frame) 58 is necessary to enable the aeroplane to reach the Extended Service Goal (ESG). The failure of the circumferential joint of the upper fuselage could affect the structural integrity of the aeroplane. * * * * * We are issuing this AD to require actions to correct the unsafe condition on these products.
2002-13-12: This amendment supersedes an existing airworthiness directive (AD), applicable to certain McDonnell Douglas Model DC-9-10, -30, and - 40 series airplanes and Model C-9 airplanes, that currently requires an inspection to detect chafing of the wiring of the attendants' work light of the aft cabin, and repair of chafed wiring. That AD also requires modification and reidentification of the attendants' work light assemblies of the aft cabin. This amendment revises the applicability of the existing AD. The actions specified by this AD are intended to prevent chafing of the ground wire against the positive contact of the lamp of the attendants' work light of the aft cabin, and consequent arcing or arcing damage to the wiring of the attendants' work light and transformer of the aft cabin. Such arcing or arcing damage could result in short circuits and consequent smoke and fire in the aft cabin area. The actions of this AD are intended to address the identified unsafe condition.The incorporation by reference of McDonnell Douglas Alert Service Bulletin DC9-33A058, Revision 02, dated January 27, 2000, as listed in the regulations, was approved previously by the Director of the Federal Register as of January 16, 2002 (66 FR 64133, December 12, 2001).
2023-14-05: The FAA is superseding Airworthiness Directive (AD) 2022-10- 08, which applied to certain Airbus SAS Model A320-214, -251N, and - 271N airplanes. AD 2022-10-08 required a one-time detailed inspection of the affected passenger seats and corrective actions if necessary. Since the FAA issued AD 2022-10-08, it was determined that additional passenger seats are affected. This AD continues to require the actions in AD 2022-10-08, and also requires inspecting additional affected passenger seats; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2020-20-17: The FAA is adopting a new airworthiness directive (AD) for all General Electric Company GE90-110B1 and GE90-115B model turbofan engines. This AD was prompted by an in-service occurrence of loss of engine thrust control resulting in uncommanded high thrust. This AD prohibits dispatch of an airplane if certain status messages are displayed on the engine indicating and crew alerting system (EICAS) and if certain conditions are present per the manufacturer's service information. As a terminating action, this AD requires revision of the existing FAA-approved minimum equipment list (MEL) by incorporating into the MEL the dispatch restrictions listed in this AD. The FAA is issuing this AD to address the unsafe condition on these products.
2002-13-02: This amendment adopts a new airworthiness directive (AD) that applies to all Air Tractor, Inc. (Air Tractor) Models AT-300, AT-301, AT-302, and AT-400A airplanes that have aluminum spar caps; certain Air Tractor Models AT-400 airplanes that have aluminum spar caps; and all Models AT-300 and AT-301 airplanes that have aluminum spar caps and are or have been converted to turbine power. This AD requires you to inspect (one-time) the wing centerline splice joint for cracks and, if any crack is found, replace the affected wing spar lower cap. This AD also requires you to report the results of the inspection to the Federal Aviation Administration (FAA) and replace the wing spar lower caps after a certain amount of usage. This AD is the result of an incident on one of the affected airplanes where the wing separated from the airplane. Preliminary reports indicate that fatigue caused the lower aluminum spar cap to fail across the 3/8-inch bolt hole (6.5 inches outboard of the fuselagecenterline in the centersplice connection). The actions specified by this AD are intended to detect and correct cracks in the wing centerline splice joint. If not detected and corrected, these cracks could eventually result in the wing separating from the airplane during flight.
2002-13-07: This amendment adopts a new airworthiness directive (AD) that applies to certain Honeywell, Inc. part number (P/N) HG1075AB05 and HG1075GB05 inertial reference units (IRU) that are installed on aircraft. This AD requires you to inspect the affected IRU's for proper function and remove the IRU either immediately or at a certain time depending on the result of the inspection. This AD is the result of a report that these IRU's may not function when using backup battery power in certain installations. The actions specified by this AD are intended to ensure the correct transition of the IRU to backup battery power upon the loss of primary power. Failure of an IRU to transition to backup battery power could result in loss of attitude, heading, and position reference and lead to the pilot making flight decisions that put the aircraft in unsafe flight conditions.
2023-16-03: The FAA is adopting a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500- 1A11 airplanes. This AD was prompted by a report from the supplier of a manufacturing quality escape in which some sensing elements were manufactured with insufficient salt fill. This could result in an inability to detect hot bleed air leaks. This AD requires, depending on airplane serial number, reviewing the airplane maintenance records for affected bleed leak detection system sensing elements, testing the sensing elements, replacing those that fail, and witness marking those that pass, as specified in a Transport Canada AD, which is incorporated by reference. This AD also prohibits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
94-11-03: This amendment adopts a new airworthiness directive (AD) that is applicable to certain Raytheon Corporate Jets Model DH/BH/HS BAe 125 and Hawker 800 and 1000 series airplanes. This action requires a visual inspection to determine whether adequate clearance exists between the fan venturi motor casing and the adjacent equipment, and adjustments, if necessary; and a visual inspection to detect signs of overheating, degradation of insulating materials, and ingestion of debris into the motor, and replacement of discrepant parts with serviceable parts. This amendment is prompted by reports of smoke emanating from the lavatory due to overheating of the fan venturi motor. The actions specified in this AD are intended to prevent smoke or fire in the cabin while the airplane is in flight. Comments for inclusion in the Rules Docket must be received on or before July 5, 1994.
2023-16-02: The FAA is adopting a new airworthiness directive (AD) for all Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500-1A11 airplanes. This AD was prompted by reports of mechanical wear damage found on the engine fuel feed system tubes and fuel tube connections. This AD requires repetitive inspections of the fuel feed system for damage, and replacement if necessary, as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2002-13-08: This amendment adopts a new airworthiness directive (AD) that applies to certain de Havilland Inc. (de Havilland) Models DHC-2 Mk. I, DHC-2 Mk. II, and DHC-2 Mk. III airplanes. This AD requires you to modify the elevator tip rib on each elevator; repetitively inspect underneath the mass balance weights at each elevator tip rib for corrosion; and either remove the corrosion or replace a corroded elevator tip rib depending on the corrosion damage. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for Canada. The actions specified by this AD are intended to detect and correct corrosion in the mass balance weights at the elevator tip ribs, which could result in loss of balance weight during flight and the elevator control surface separating from the airplane.
2023-16-04: The FAA is adopting a new airworthiness directive (AD) for certain Piaggio Aviation S.p.A. (Piaggio) Model P-180 airplanes. This AD was prompted by a report of corrosion-induced cracking on the horizontal tail trim actuator (HTTA) fitting assembly. This AD requires repetitively inspecting the HTTA fitting assembly for corrosion and cracking until the HTTA fitting assembly is replaced with a new part. The FAA is issuing this AD to address the unsafe condition on these products.
2017-26-03: We are adopting a new airworthiness directive (AD) for the Enstrom Helicopter Corporation (Enstrom) Model F-28, F-28A, F-28C, F- 28C-2, F-28C-2R, F-28F, F-28F-R, TH-28, 280, 280C, 280F, 280FX, 480, and 480B helicopters. This AD requires inspecting certain rod end bearing assemblies. This AD is prompted by an accident. The actions of this AD are intended to prevent an unsafe condition on these helicopters.
99-27-16 R1: This amendment revises an existing airworthiness directive (AD), that is applicable to CFE Company Model CFE738-1-1B turbofan engines. That AD currently requires a one-time visual inspection of stage 2 high pressure turbine (HPT) aft cooling plates for nicks, dents, raised metal, and scratches, and if necessary, repair of the cooling plates or replacement with serviceable parts. This amendment reduces the number of stage 2 HPT aft cooling plates affected by AD 99-27-16, and identifies the applicable engines by engine serial numbers (SN's). This amendment is prompted by an updated alert service bulletin (ASB) that reduces the number of stage 2 HPT aft cooling plates affected by AD 99-27-16 and identifies the applicable engines by engine SN's. The actions specified by this AD are intended to prevent stage 2 HPT aft cooling plate failure, which could result in an uncontained engine failure and damage to the airplane.
74-16-06: 74-16-06 CESSNA: Amendment 39-1911. Applies to Models 177 (Serial Numbers 17700001 thru 17702041), 177RG (Serial Numbers 177RG00001 thru 177RG0445) and F177RG (Serial Numbers F177RG0001 thru F177RG0092) airplanes. \n\n\tCompliance: Within the next 50 hours' time in service after the effective date of this AD, unless already accomplished. \n\n\tTo prevent failure or chafing of the oil pressure gage line located between the firewall and the oil pressure gage, install clamps between the flap control cable and the oil pressure gage line in accordance with Cessna Service Letter SE74-2 dated January 25, 1974, or later approved revisions. Any alternate method of compliance must be approved by Chief, Engineering and Manufacturing Branch, FAA, Central Region. \n\n\tThis amendment becomes effective August 9, 1974.
2002-13-04: This amendment supersedes emergency airworthiness directive (AD) 2000-11-51 that was sent previously to all known U.S. owners and operators of Teledyne Continental Motors (TCM) O-300, IO-360, TSIO-360, and LTSIO-520-AE series reciprocating engines. That action required within 10 flight hours after receipt of that AD, replacement of certain magnetos if they fall within the specified serial number range, inspection of the removed magneto to verify that the stop pin is still in place, and, if the stop pin is not in place, inspection of the engine gear train. This amendment requires the same replacement and inspections and adds TCM C-125 and C145 series reciprocating engines to the applicability, which were inadvertently omitted from the emergency AD. This amendment is prompted by reports of engine failures on certain TCM reciprocating engines. The actions specified by this AD are intended to prevent engine failure and loss of control of the airplane due to migration of the magneto impulse coupling stop pin out of the magneto frame and into the gear train of the engine.
2023-14-06: The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model EC120B, EC130B4, and EC130T2 helicopters. This AD was prompted by a report of corrosion detected on certain part- numbered landing gear assemblies. This AD requires, for helicopters with certain part-numbered landing gear assemblies installed, visually inspecting for cracks and corrosion; borescope inspecting; and if required, removing corrosion, measuring thickness, interpreting results of the measurements, applying chemical conversion coating and primer, and removing affected parts (landing gear assembly) and affected part sub-assemblies (front or rear crossbeam or left-hand or right-hand skid assembly) from service and replacing with airworthy parts. This AD will allow an affected part or affected part sub-assembly to be installed on a helicopter if certain actions in this AD are accomplished. The FAA is issuing this AD to address the unsafe condition on these products.
2025-08-07: The FAA is superseding Airworthiness Directive (AD) 2006-20- 08, which applied to all Embraer S.A. Model EMB-145, -145ER, -145MR, - 145LR, -145XR, -145MP, and -145EP airplanes. AD 2006-20-08 required repetitive inspections to detect cracking or failure of the rod ends and fittings of the aileron power control actuator (PCA), and corrective actions if necessary, and provided an optional terminating action. This AD was prompted by a determination that there was an error in identifying a maintenance task number. This AD continues to require the actions in AD 2006-20-08 and corrects an error in a task number, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2002-13-03: This amendment supersedes an existing airworthiness directive (AD), that is applicable to certain CFM International (CFMI) CFM56 series turbofan engines. That AD currently requires revisions to the Airworthiness Limitations Section of applicable Engine Shop Manuals (ESM's) to include required enhanced inspection of selected critical life-limited parts at each piece-part exposure. This amendment requires revisions to the Airworthiness Limitations Section of the applicable manufacturer's manuals and air carrier's approved continuous airworthiness maintenance program to incorporate additional inspections of selected critical life-limited parts at each piece-part exposure. This amendment is prompted by an FAA study of in-service events involving uncontained failures of critical rotating parts. The actions specified by this AD are intended to prevent critical life-limited rotating engine part failure, which could result in an uncontained engine failure and damage to the airplane.
2002-13-01: This amendment adopts a new airworthiness directive (AD), applicable to certain McDonnell Douglas Model MD-90-30 airplanes, that requires an inspection of the galley power feeder cable above the main cabin ceiling supports for damage caused by chafing. The amendment also requires repairing any damage on the outer cable jacket or primary insulation, installing a splice on the power feeder cable to remove damage, installing sleeving along a portion of the cable, installing standoffs for the cable, re-routing the galley power feeder cable, and testing the galley equipment, as applicable. The actions specified by this AD are intended to prevent future damage to the galley power feeder cable as well as to detect and correct existing damage to the galley power feeder cable, which could result in electrical arcing, possibly leading to damage to adjacent structures and to fire in the airplane. This action is intended to address the identified unsafe condition.
2023-14-07: The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model EC155B1 helicopters. This AD was prompted by reports of failure of the main gearbox (MGB) oil cooling fan hub (fan hub). This AD requires, for helicopters with an affected part (fan hub) installed, using an endoscope, repetitively inspecting the fan hub, including the area around the fan hub attachment screws, for a crack. Depending on the inspection results, this AD requires performing additional inspections and replacing an affected fan hub. This AD also allows an affected fan hub to be installed on a helicopter if certain actions are accomplished, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2017-26-01: We are adopting a new airworthiness directive (AD) for certain General Electric Company (GE) GEnx-1B64/P2, -1B67/P2, -1B70/P2, -1B70/ 75/P2, -1B70C/P2, and -1B74/75/P2 turbofan engines. This AD was prompted by a report of the failure of the high-pressure turbine (HPT) stage 1 blade retainer and subsequent in-flight shutdown of the engine. This AD requires inspection of the HPT stage 1 blade retainer. We are issuing this AD to address the unsafe condition on these products.
2011-03-14: We are adopting a new airworthiness directive (AD) for the products listed above. This AD requires installing two warning level indicator lights on the P2-2 center instrument panel in the flight compartment for certain airplanes. For a certain other airplane, this AD requires activating the cabin altitude warning and takeoff configuration warning lights. For all airplanes, this AD also requires revising the airplane flight manual to remove certain requirements included by previous AD actions, requires new pressure altitude limitations for certain airplanes, and advises the flightcrew of the following changes: revised emergency procedures to use when a cabin altitude warning or rapid depressurization occurs, and revised cabin pressurization procedures for normal operations. This AD was prompted by a design change in the cabin altitude warning system that would address the identified unsafe condition. We are issuing this AD to prevent failure of the flightcrew to recognize and react properly to a valid cabin altitude warning horn, which could result in incapacitation of the flightcrew due to hypoxia (lack of oxygen in body), and consequent loss of control of the airplane.
2023-14-09: The FAA is superseding Airworthiness Directive (AD) 2022-17- 09, which applied to certain Airbus SAS Model A350-941 and -1041 airplanes. AD 2022-17-09 continued to require the actions of AD 2021- 16-03 and required a modification to restore two independent layers of lightning strike protection. This AD was prompted by reports of the incorrect application of lightning strike edge glow sealant protection at specific locations on the wing tanks, and a determination that additional airplanes need to perform a modification to restore two independent layers of lightning strike protection on the wing lower or upper cover. This AD continues to require the actions in AD 2022-17-09, and also requires restoring the two independent layers of lightning strike protection; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2002-12-13: This amendment adopts a new airworthiness directive (AD), applicable to all Boeing Model 727 series airplanes, that requires a review of maintenance records or a one-time test to determine if elevator hinge support ribs on the trailing edge of the horizontal stabilizer are made from a certain material, and follow-on repetitive inspections for corrosion or cracking of the elevator hinge support ribs, if necessary. For airplanes with the affected ribs installed, this AD eventually requires replacement of all affected ribs with new, improved ribs. This action is necessary to prevent cracking of the elevator hinge support ribs, which could lead to vibration of the airframe during flight and consequent damage to the elevator and horizontal stabilizer, potentially resulting in loss of controllability of the airplane. This action is intended to address the identified unsafe condition.
2025-10-03: The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.