Results
2013-25-06: We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This AD was prompted by a determination that certain maintenance activities, such as repairs or the accumulation of paint layers, might cause the weight of an elevator to exceed the certified limits. This AD requires checking the weight of certain elevators, and corrective action if necessary; and re-identifying the elevators. We are issuing this AD to detect and correct elevators that exceed the certified weight limits, which could result in reduced control of the airplane.
2013-26-12: We are superseding Airworthiness Directive (AD) 2009-14-02 for certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747- 200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. AD 2009-14-02 required repetitive inspections for wear damage and cracks of the fuselage skin in the interface area of the vertical stabilizer seal and fuselage skin, a detailed inspection for wear damage and cracks of the surface of any skin repair doubler in the area, and corrective actions if necessary. For airplanes on which the fuselage skin has been blended to remove wear damage, AD 2009-14-02 also required repetitive external detailed inspections or high frequency eddy current inspections for cracks of the blended area of the fuselage skin, and corrective actions if necessary. This new AD reduces the repetitive inspection interval, changes certain corrective actions, and expands the applicability. This AD was prompted by a report of wear through the fuselage skin that occurred sooner than the previous repetitive inspection interval. We are issuing this AD to detect and correct wear damage and cracks of the fuselage skin in the interface area of the vertical stabilizer seal and fuselage skin in sections 46 and 48, which could cause in-flight depressurization of the airplane.
2003-13-07: This amendment adopts a new airworthiness directive (AD) that applies to all Short Brothers and Harland Ltd. (Shorts) Models SC-7 Series 2 and SC-7 Series 3 airplanes. This AD requires you to repetitively inspect all flight control system rods for corrosion and cracks, replace any cracked rod, and repair corrosion damage or replace any corroded rod depending on the extent of the damage. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for the United Kingdom. The actions specified by this AD are intended to prevent failure of any flight control system rod caused by cracks or corrosion. Such failure could lead to complete failure of the flight control system with consequent loss of control of the airplane.
2013-26-07: We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This AD was prompted by reports of certain sliding windows that were difficult to operate after landing. This AD requires a detailed inspection to identify part numbers of sliding windows and sliding window seals, and modification if necessary. This AD also includes an optional replacement. We are issuing this AD to detect and correct incorrect seals, which could lead to the functional loss of the sliding window as an exit, possibly preventing the flightcrew from safely evacuating the airplane during an emergency.
2013-26-06: We are superseding airworthiness directive (AD) 2010-19-01 for certain Rolls-Royce Corporation (RRC) AE 3007A series turbofan engines. AD 2010-19-01 required removing certain high-pressure turbine (HPT) stage 2 wheels, or performing inspections on them, and reduced their approved life limits. This new AD clarifies the AE 3007A turbofan engine model applicability, further reduces the approved life limits of affected HPT stage 2 wheels, and eliminates the inspections required by the existing AD. This AD was prompted by additional analysis that concluded that lower life limits for the affected HPT stage 2 wheels are necessary. We are issuing this AD to prevent uncontained failure of the HPT stage 2 wheel, damage to the engine, and damage to the airplane.
2013-26-04: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-400, -400D, and -400F series airplanes. This AD was prompted by a report of water leakage into the main deck cargo wire integration unit (WIU). The water flowed from the main deck floor panels, through disbonded seams in the aft main equipment center (MEC) drip shield gutter, then onto the WIU. This AD requires cleaning the aft MEC drip shield gutter; and doing a one-time general visual inspection for disbonded seams, and repair if necessary. This AD also requires installing a fiberglass reinforcement overcoat to the underside of the bonded seams of the aft MEC drip shield gutters. We are issuing this AD to prevent water penetration into the MEC, which could result in the loss of flight critical systems.
2018-07-17: We are adopting a new airworthiness directive (AD) for certain Safran Helicopter Engines, S.A., Arrius 2B1, 2B1A, 2B2, and 2K1 turboshaft engines. This AD requires inspecting the power turbine wheel (PTW) assembly and replacing the PTW if the turbine blade dampers are found missing. This AD was prompted by the manufacturer reporting a number of PTW assemblies may have been assembled without the blade dampers. We are issuing this AD to address the unsafe condition on these products.
2013-26-01: We are adopting a new airworthiness directive (AD) for all CFM International (CFM) S.A. CFM56-3 and CFM56-7B series turbofan engines with certain accessory gearboxes (AGBs) not equipped with a handcranking pad ``oil dynamic seal'' assembly. This AD was prompted by 42 events of total loss of engine oil from CFM56 series turbofan engines while in flight. This AD requires an independent inspection to verify re-installation of the handcranking pad cover after removal of the pad cover for maintenance until installation of a handcranking pad oil dynamic seal assembly. We are issuing this AD to prevent loss of engine oil while in flight, which could result in engine failure, loss of thrust control, and damage to the airplane.
2025-05-15: The FAA is adopting a new airworthiness directive (AD) for all General Electric Company (GE) Model CT7-2E1 engines. This AD was prompted by a revised analysis using an updated stress model, which calculated that the actual life limit of the CT7-2E1 stage 2 turbine aft cooling plate is less than the current life limit. This AD requires revision of the airworthiness limitations section (ALS) of the existing CT7-2E1 engine maintenance manual (EMM) and the operator's existing approved maintenance program or inspection program, as applicable, to incorporate a reduced life limit for this part. The FAA is issuing this AD to address the unsafe condition on these products.
2003-12-13: This amendment adopts a new airworthiness directive (AD) for Agusta S.p.A (Agusta) Model A109K2 helicopters. This action requires a visual check of each tail rotor blade (blade) for a crack; a visual inspection of each blade for a crack at specified intervals; and if necessary, a dye-penetrant inspection. Replacing any cracked blade with an airworthy blade before further flight is also required. This amendment is prompted by a report of a crack that occurred on an Agusta Model A109K2 blade. The actions specified in this AD are intended to detect fatigue cracks on the blades, which could result in loss of the blades and loss of control of the helicopter.
2018-07-10: We are adopting a new airworthiness directive (AD) for Embraer S.A. Models EMB-500 and EMB-505 airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as improperly tied castle nuts on the aileron, rudder, and elevator trim tab (or autotab) attachment bolts. We are issuing this AD to require actions to address the unsafe condition on these products.
2013-26-02: We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2C10 (Regional Jet Series 700, 701, & 702), CL-600-2D15 (Regional Jet Series 705), and CL-600-2D24 (Regional Jet Series 900) airplanes. This AD was prompted by a report that traces of oil could be found in the crew oxygen system due to the use of incorrect pressure testing procedures during manufacturing. This AD requires cleaning the crew oxygen system. We are issuing this AD to detect and correct oil contaminants, which could cause an ignition and result in a fire in the oxygen system.
2013-26-03: We are superseding airworthiness directive (AD) 2011-24-09 which applied to certain Airbus Model A340-200 and A340-300 series airplanes. AD 2011-24-09 requires inspections to verify electrical bonding for the water drain system and ventilation intake system, and modification if necessary. This new AD requires revising the maintenance program to incorporate certain maintenance requirements and airworthiness limitations, and adds additional airplanes to the applicability. This AD was prompted by a determination that existing maintenance requirements are not adequate to address the unsafe condition. We are issuing this AD to prevent the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
97-18-02R1: This amendment revises an existing airworthiness directive (AD), that is applicable to Hartzell Propeller Inc. ( )HC-( )(2,3)(X,V)( )-( ) series and HA-A2V20-1B series propellers with aluminum blades. That AD currently requires initial and repetitive dye penetrant and eddy current inspections of the blade and an optical comparator inspection of the blade retention area, and, if necessary, replacement with serviceable parts. In addition, that AD currently requires initial and repetitive visual and magnetic particle inspection of the blade clamp, dye penetrant inspection of the blade internal bearing bore, and, if necessary, replacement with serviceable parts. Also, for all HC-(1,4,5,8)(2,3)(X,V)( )-( ) steel hub propellers, that AD currently requires an additional initial and repetitive visual and magnetic particle inspection of the hub, and, if necessary, replacement with serviceable parts. This amendment revises that AD by permitting the replacement of affected propellers with Hartzell Propeller Inc. model "MV" series propellers as an optional terminating action for the initial and repetitive inspections of that AD. This amendment is prompted by type certification approval of the Hartzell "MV" series propellers that are direct replacements for the affected propellers, and service bulletin approval to allow modification of affected propellers to the "MV" type design configuration. The actions specified by this AD are intended to prevent blade separation due to cracked blades, hubs, or blade clamps, which can result in loss of control of the airplane.
2013-25-05: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-300, -400, and -500 series airplanes. This AD was prompted by fuel system reviews conducted by the manufacturer. This AD requires, depending on airplane configuration, replacing fuel pump power control relays with new relays having a ground fault interrupter (GFI) feature, installing ground studs and a bonding jumper, doing certain bonding resistance measurements, and changing the GFI relay position. This AD also requires revising the maintenance program to incorporate certain airworthiness limitations. We are issuing this AD to prevent damage to the fuel pumps caused by electrical arcing that could introduce an ignition source in the fuel tank, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
2013-25-11: We are superseding Airworthiness Directive (AD) 2010-24-07 for all Airbus Model A318 series airplanes, Model A319 series airplanes, Model A320 series airplanes, and Model A321 series airplanes. AD 2010- 24-07 required repetitive inspections of the 80VU rack lower lateral fittings for damage, repetitive inspections of the 80VU rack lower central support for cracking, and corrective action if necessary. AD 2010-24-07 also specified optional terminating action for the repetitive inspections. This new AD reduces the inspection compliance time, adds an inspection of the upper fittings and shelves of the 80VU rack, and adds airplanes to the applicability. This AD was prompted by reports of worn lower lateral fittings of the 80VU rack. We are issuing this AD to detect and correct damage or cracking of the 80VU fittings and supports, which could lead to possible disconnection of the cable harnesses to one or more computers, and if occurring during a critical phase of flight, could result in reduced control of the airplane.
2013-24-05: We are adopting a new airworthiness directive (AD) for certain Turbomeca S.A. Arriel 1A1, 1A2, 1B, 1C, 1C1, 1C2, 1D, 1D1, 1E2, 1K1, 1S, and 1S1 turboshaft engines. This AD requires a one-time inspection of the free turbine (FT) module (M04) for the affected Turbomeca S.A. Arriel 1 engines and, if a discrepancy is found, repair of the affected module. This AD was prompted by a ``chip illumination event'' in flight on a Turbomeca S.A. Arriel 1 engine. We are issuing this AD to prevent a loss of FT bearing lubrication, resulting in FT module failure, damage to the engine, and damage to the aircraft.
2013-24-19: We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model AS332C, AS332L, AS332L1, AS332L2, and EC225LP helicopters. This AD requires visually inspecting each jettisonable emergency exit window panel (window) for sealant, and removing any sealant that exists in the window's extruded sections. This AD was prompted by jettison tests during routine maintenance inspections that showed the windows failed to jettison. The actions of this AD are intended to prevent failure of the windows to jettison, so helicopter occupants can exit the aircraft during an emergency.
2025-05-03: The FAA is superseding Airworthiness Directive (AD) 2024-06-06 for all Rolls-Royce Deutschland Ltd & Co KG (RRD) Model Trent7000-72 and Trent7000-72C engines. AD 2024-06-06 required revising the airworthiness limitations section (ALS) of the operator's existing approved engine maintenance or inspection program, as applicable, to incorporate new or more restrictive tasks and limitations and associated thresholds and intervals for life-limited parts. Since the FAA issued AD 2024-06-06, the manufacturer has revised the engine time limits manual (TLM) to introduce new or more restrictive tasks and limitations and associated thresholds and intervals for life-limited parts, which prompted this AD. This AD requires revising the ALS of the existing approved engine maintenance or inspection program, as applicable, to incorporate new or more restrictive tasks and limitations and associated thresholds and intervals for life-limited parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2013-24-18: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-200B, -200C, -200F, -300, and 747SR series airplanes. This AD was prompted by reports of cracks of both lower chords and web on certain outboard struts. This AD requires repetitive inspections for cracking of the lower spar chords and web, web lower spar chord modification, which includes inspections for cracking of the lower spar chords, and repetitive post modification inspections for cracking of the lower spar web and chord; and applicable corrective actions. We are issuing this AD to prevent cracked chords and web on certain outboard struts, which, if the chord severs, could result in reduced structural integrity of the diagonal brace load path and of the strut-to-wing attachment, and \n\n((Page 76048)) \n\nconsequent separation of a strut and engine from the airplane during flight.
2013-24-09: We are adopting a new airworthiness directive (AD) for certain EADS CASA (Type Certificate Previously Held by Construcciones Aeron[aacute]uticas, S.A.) Model C-212-CB, C-212-CC, C-212-CD, C-212- CE, and C-212-DF airplanes. This AD was prompted by a report of the propeller pitch control (PPC) lever becoming disconnected from the engine due to a missing bolt. This AD requires modifying the PPC lever attachment system. We are issuing this AD to prevent PPC shaft disconnection, which could lead to a loss of propeller pitch control, possibly resulting in uncommanded change to the engine power settings and consequent reduced controllability of the airplane.
2013-24-13: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-100, -200, -200C, -300, -400, -500, -600, -700, -700C, -800, and -900 series airplanes. This AD was prompted by a report that the seat track attachment of body station 520 flexible joint is structurally deficient in resisting a 9g forward emergency load condition in certain seating configurations. This AD requires replacing the pivot link assembly on certain seats, modifying the existing seat track link assembly fastener on certain seats, or replacing the seat track link assemblies on certain seats. Also, for certain airplanes, this AD requires installing a new seat track link assembly or modifying the seat track link assembly. For certain other airplanes, this AD requires inspecting, changing, or repairing the seat track link assembly. We are issuing this AD to prevent seat detachment in an emergency landing, which could cause injury to occupants of the passenger compartment and affectemergency egress.
2013-23-18: We are adopting a new airworthiness directive (AD) for certain General Electric Company (GE) GE90-110B1 and -115B turbofan engines. This AD was prompted by multiple events of a leaking variable bypass valve (VBV) actuator fuel supply tube. This AD requires replacement of this VBV actuator fuel supply tube with a part eligible for installation. We are issuing this AD to prevent failure of the affected fuel supply tube, fuel leakage, engine fire, and damage to the airplane.
2000-24-18: This amendment adopts a new airworthiness directive (AD), applicable to certain Airbus Model A300 B2 and B4 series airplanes, and Model A300-600 series airplanes, that requires repetitive inspections to detect chafing and the existence of repairs of the harness of the high-level sensor of the fuel surge tanks, and to detect chafe marks on the support canisters of the magnetic level indicators; and follow-on corrective actions, if necessary. This amendment also requires modification of the harness for the high-level sensor of the outer wing fuel tanks, which terminates certain repetitive inspections. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by this AD are intended to prevent chafing of the harness of the high-level sensor, which could result in a short circuit and consequent fuel ignition source inside the outer wing fuel tanks.
75-08-02: 75-08-02 DE HAVILLAND: Amendment 39-2149. Applies to de Havilland Model DHC- 6 Series Twin Otter Aircraft, Serial Nos. 1 through 135 inclusive. Compliance required as indicated. To preclude the hazard created by the failure of the right hand aileron control cable through contact with DC electrical power cable coded 2P66A8, accomplish the following: (a) Within the next 100 hours' time in service after the effective date of this A.D., alter the attachment of terminal block TB-17 and the routing of the cable harness to terminal block TB-17 and TB-18 in accordance with de Havilland Service Bulletin No. 6/304, Revision B, dated June 28, 1974, or equivalent alteration approved by the Chief, Engineering and Manufacturing Branch, FAA Eastern Region. (b) Upon request with substantiating data submitted through an FAA inspector, the compliance time specified in this A.D. may be increased by the Chief, Engineering and Manufacturing Branch, FAA Eastern Region. This amendment is effective April 7, 1975.