Results
2014-17-02: We are superseding Airworthiness Directive (AD) 2013-18-09 for certain Honeywell ASCa Inc. emergency locator transmitters (ELTs) installed on various transport category airplanes. AD 2013-18-09 required various one-time general visual inspections of the ELT transmitter units (TUs), and corrective actions if necessary. This new AD corrects the manufacturer's name in the AD applicability and adds a source of approval for an installation. AD 2013-18-09 was prompted by a fire on a parked and unoccupied airplane; preliminary information indicated combustion in the area of the ELT TU. This new AD was prompted by the identification of an error in the applicability of AD 2013-18-09. We are issuing this AD to detect and correct discrepancies of the battery wiring installation inside the TU, which could result in an electrical short and possible ignition source.
2003-13-13: This amendment adopts a new airworthiness directive (AD) for the specified Bell Helicopter Textron Canada (Bell) model helicopters that requires a one-time inspection of the adjustable stop screws of the magnetic brake assembly; repairing, as appropriate, certain mechanical damage to the cyclic and collective flight control magnetic brake arm assembly (arm assembly), if necessary; and installing the stop screw with the proper adhesive, adjusting the arm assembly travel, and applying slippage marks. This amendment is prompted by reports that the magnetic brake adjustable screws have backed out, which limited travel of the arm assembly. The actions specified by this AD are intended to detect loose adjustable stop screws that could result in limiting the travel of the cyclic and collective arm assembly, and subsequent loss of control of the helicopter.
2014-16-19: We are superseding Airworthiness Directives (AD) 2006-21-08, AD 2007-14-01, AD 2008-25-02, AD 2010-04-09, AD 2011-01-02, and AD 2012-16-05, for certain Airbus Model A330 and A340 series airplanes. AD 2006-21-08, AD 2007-14-01, AD 2008-25-02, AD 2010-04-09, AD 2011-01-02, and AD 2012-16-05 required revising the maintenance program or inspection program to incorporate certain maintenance requirements and airworthiness limitations for fuel tank systems. This new AD requires a new maintenance or inspection program revision. This AD was prompted by a determination that more restrictive maintenance requirements and airworthiness limitations are necessary. We are issuing this AD to prevent the potential of ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane.
2014-15-51: We are adopting a new airworthiness directive (AD) for certain Embraer S.A. Model EMB-500 airplanes. This AD was sent previously to all known U.S. owners and operators of these airplanes as an emergency AD. This AD requires an inspection and replacement as necessary of the barrel nuts at the horizontal stabilizer to vertical stabilizer attachment joint. This AD was prompted by mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracking of the barrel nuts at the horizontal stabilizer to vertical stabilizer attachment joint. We are issuing this AD to correct the unsafe condition on these products.
74-05-05: 74-05-05 BEECH: Amendment 39-1796 as amended by Amendment 39-1841. Applies to Models 60 and A60 (Serial Numbers P-3 through P-246) airplanes now having or subsequently accruing 27 months in service from the date of the original airworthiness certification, except those airplanes having Beech P/N 60-420013-59 or Beech P/N 60-420013-652 pilot's side window installed. Compliance: Required as indicated. To prevent rapid decompression caused by failure of the pilot's side window accomplish the following: A) Effective immediately, operation with the cabin pressurized is prohibited and prior to further flight (1) deactivate the pressurization system by securing the "TEST/DUMP" switch in the "Dump" position and install a placard on the control panel adjacent to the pressurized system controls reading: "CABIN PRESSURIZATION PROHIBITED" and (2) insert a copy of this AD in the limitation section of the airplane flight manual. B) In lieu of Paragraph A(1) and (2), and prior to operation with cabin pressurization, replace existing pilot's side window with Beech P/N 60-420013-59 or Beech P/N 60-420013-652 pilot side window in accordance with Beechcraft Service Instructions No. 0594- 110, or later approved revisions or any equivalent approved by the Chief, Engineering and Manufacturing Branch, FAA, Central Region. C) Upon accomplishment of Paragraph B, reactivate the pressurization system and remove the placard and flight manual insertion required by Paragraph A. Amendment 39-1796 became effective March 8, 1974. This Amendment 39-1841 becomes effective May 17, 1974.
2009-19-51: This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2009-19-51, which was sent previously to all known U.S. owners and operators of the Agusta Model AB139 and AW139 helicopters by individual letters. This AD requires inspecting the tail panels for debonding and, if the debonding area exceeds a certain limit, repairing the tailboom. This AD results from a mandatory continuing airworthiness information (MCAI) AD issued by the European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community. The MCAI AD states that while taxiing, the tailboom of a Model AW139 helicopter bent and collapsed. Also, EASA had received previous reports of evidence of debonding on some tailboom panels of the specified Agusta model helicopters. This condition, if not corrected, could result in failure of a tailboom and subsequent loss of control of the helicopter. DATES: Effective on February 8, 2010,to all persons except those persons to whom it was made immediately effective by Emergency AD 2009- 19-51, issued on September 16, 2009, which contained the requirements of this amendment. Comments for inclusion in the Rules Docket must be received on or before March 23, 2010.
2014-15-13: We are superseding Airworthiness Directive (AD) 2005-15-04 for certain Bombardier, Inc. Model CL-600-1A11 (CL-600), CL-600-2A12 (CL- 601), and CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604 Variants) airplanes. AD 2005-15-04 required operators to assign serial numbers or part numbers to certain landing gear parts; establish the number of landings on the parts, if necessary; and revise the Airworthiness Limitations Section (ALS) of the Instructions for Continued Airworthiness (ICA) to reflect the new life limits of the landing gear parts. This new AD adds airplanes to the applicability, requires operators to assign serial numbers or part numbers to certain additional landing gear parts to establish the number of landings on the parts if necessary, and requires operators to record in all required airplane technical records and manuals the new part numbers, serial numbers, and landings assigned to these parts. This AD was prompted by reports that landing gear parts that have safe-life limits but do not have serial numbers or part numbers can be removed from one landing gear and re-installed on another, making tracking difficult. We are issuing this AD to prevent life-limited landing gear parts from being used beyond their safe-life limits, which could lead to collapse of the landing gear.
2013-13-13: We are adopting a new airworthiness directive (AD) for all Airbus Model A310 series airplanes; and Model A300 B4-600, B4-600R, and F4-600R series airplanes, and Model A300 C4-605R Variant F airplanes (collectively called A300-600 series airplanes). This AD was prompted by the revision of certain airworthiness limitation items (ALI) documents, which require more restrictive maintenance requirements and airworthiness limitations. This AD requires revising the maintenance or inspection program to incorporate the limitations section. We are issuing this AD to prevent fatigue cracking, damage, or corrosion in principal structural elements, which could result in reduced structural integrity of the airplane.
72-18-01: 72-18-01 BEECH: Amdt. 39-1505. Applies to Models 35, A35, B35 and C35 airplanes (Serial Numbers D-1 through D-2900) with a P/N 35-924065 fuel unit modified by the installation of Beech Kit No. 35-5030S (Serial Numbers 100 through 989) or any equivalent installation using a warning light with a dimming feature. (NOTE: Installation of either Beech Kit No. 35-5030S or P/N 35-924230 fuel unit is required by AD 69-18-01.) To prevent dimming of fuel selector valve disengagement warning light, unless already accomplished, accomplish the following: A) Effective immediately until Paragraph B has been accomplished, adjust the dimming lens on the fuel selector valve disengagement warning light to maximum bright. B) Within the next 25 hours' time in service after the effective date of this AD, either replace MS 25041-2 light indicator assembly with MS 25041-6 light indicator assembly or replace the dimming lens assembly of the MS 25041-2 light assembly with the non-dimming lens assembly from an MS 25041-6 light assembly. Any equivalent method of compliance must be submitted to and approved by the Chief, Engineering and Manufacturing Branch, FAA, Central Region. This amendment becomes effective August 29, 1972.
2021-05-21: The FAA is superseding Airworthiness Directive (AD) 2017-23-08 for Agusta S.p.A. (now Leonardo S.p.a.) Model AB139 and AW139 helicopters. AD 2017-23-08 required repetitively inspecting the main rotor (M/R) rotating scissors, removing certain lower half scissor spherical bearings (bearings) from service, replacing the removed bearings with a new bearing, and installing a special nut. This new AD retains the requirements of AD 2017-23-08 and requires replacing each affected bearing with a certain part-numbered bearing. This AD was prompted by investigation results determining that a quality control issue may have affected the production of the affected bearings. The actions of this AD are intended to address an unsafe condition on these products.
2014-16-06: We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-600-2B16 (CL-604 Variant) airplanes. This AD was prompted by reports of in-flight uncommanded rudder movements. This AD requires revising the airplane flight manual (AFM) to incorporate an uncommanded yaw motion procedure. We are issuing this AD to prevent in- flight uncommanded rudder movements, which could lead to structural failure and subsequent loss of the airplane.
2014-16-11: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200 series airplanes. This AD was prompted by reports of smoke or flames in the passenger cabin of various transport category airplanes related to the wiring for the passenger cabin in-flight entertainment (IFE) system, cabin lighting, and passenger seats. This AD requires, for certain airplanes, doing an inspection of the electrical power control panel for a certain part number, and corrective action if necessary; and, for certain other airplanes, installing a new electrical power control panel, and making changes to the wiring and certain electrical load management system (ELMS) panels. We are issuing this AD to ensure that the flightcrew is able to turn off electrical power to the IFE systems and other non- essential electrical systems through one or two switches in the flight deck in the event of smoke or flames. In the event of smoke or flames in the airplane flight deck or passenger cabin, the flightcrew's inability to turn off electrical power to the IFE system and other non- essential electrical systems could result in the inability to control smoke or flames in the airplane flight deck or passenger cabin during a non-normal or emergency situation, and consequent loss of control of the airplane.
2003-13-16: This amendment adopts a new airworthiness directive (AD) that applies to certain Raytheon Aircraft Company (Raytheon) 90, 100, and 200 series airplanes. This AD requires you to inspect the forward side of the aft pressure bulkhead for scoring damage and repair, if necessary. This AD is the result of reports of the aft pressure bulkhead being damaged by scoring during manufacture. The actions specified by this AD are intended to detect and correct damage to the aft pressure bulkhead of the fuselage. Such damage could lead to fatigue failure of the bulkhead.
2009-23-12: We are revising an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: During a SOCATA flight test, it has been noted some difficulties for the pilot to release oxygen. After investigation it has been found that, due to the design of the oxygen generator release pin, one of the mask's lanyard linked to the pin can be jammed when it is pulled by a pilot or a passenger. This condition, if not corrected, would lead, in case of an emergency procedure due to decompression, to a risk of generator fault with subsequent lack of oxygen on crew and/or passenger. * * * This revision has been released to clarify the applicability. We are issuing this AD to require actions to correct the unsafe condition on these products.
75-13-05: 75-13-05 HAWKER SIDDELEY AVIATION, LTD: Amendment 39-2233 as amended by Amendment 39- 2302. Applies to Hawker Siddeley DH/BH. 125 airplanes certificated in all categories. Compliance required as indicated, unless already accomplished. To prevent possible failure of cockpit side window Panel "C" assemblies, within two calendar years time in service on original cockpit side window Panel "C" assemblies, or 25 hours time in service on such panels after the effective date of this AD, whichever occurs later, remove the original cockpit side window Panel "C" assemblies having part numbers given in the following table and install in place thereof the corresponding new window assemblies given in the table, in accordance with the instructions for the specific airplane model contained in Hawker Siddeley Aviation, Ltd., Alert Service Bulletin 56-A16, Revision 1, dated May 29, 1974, and accompanying Modification Service Bulletin 56-16 (2410), Revision 2, dated May 23, 1975, or an FAA approved equivalent. ORIGINAL PART NO. REPLACEMENT PART NO. 25FN57A(L/H) replace with 25-6FN219/1A or 25-6FN219/7A 25FN4865A or replace with 25-6FN219/1A or 25FN4865A/B(L/H) 25-6FN219/7A 25FN58A(R/H) replace with 25-6FN220/2A or 25-6FN220/8A 25FN4866A or replace with 25-6FN220/2A or 25FN4866A/B(R/H) 25-6FN220/8A Amendment 39-2233 became effective June 4, 1975. This amendment 39-2302 becomes effective August 15, 1975.
2014-16-08: We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-215-6B11 (CL-215T Variant), and CL-215-6B11 (CL-415 Variant) airplanes. This AD was prompted by several reports indicating that shorter nacelle strut bushings were inadvertently installed on certain airplanes. This AD requires a general visual inspection of the left and right nacelle upper strut bushings; installation of the bolts and preload indicating (PLI) washers, if necessary; and replacement of the bushing or repair of the bushing installation, if necessary. We are issuing this AD to detect and correct inadequate nacelle strut bushings, which provide insufficient engagement in the strut fork end, and could deform under the bearing load and lead to the failure of the joint.
2014-16-04: We are superseding Airworthiness Directive (AD) 2008-14-17 for certain Airbus Model A330-200 and A340-300 series airplanes. AD 2008- 14-17 required a high frequency eddy current (HFEC) inspection, corrective actions if necessary, and modifications. This new AD requires the same actions as those required by AD 2008-14-17, but with a reduced compliance time. This AD was prompted by a determination from a fatigue and damage tolerance evaluation that the compliance time needs to be revised. We are issuing this AD to detect and correct damage of the upper shell structure at the skin and frame interface, which could result in reduced structural integrity of the airframe.
2009-02-06 R1: We are revising an existing airworthiness directive (AD) that applies to certain Boeing Model 737-300, -400, and -500 series airplanes. That AD currently requires repetitive high frequency eddy current inspections for cracking of the 1.04-inch nominal diameter wire penetration hole in the frame and frame reinforcement, between stringers S-20 and S-21, on both the left and right sides of the airplane, and related investigative and corrective actions if necessary. This new AD clarifies certain compliance requirements. This AD results from reports of cracking in the frame, or in the frame and frame reinforcement, common to the 1.04-inch nominal diameter wire penetration hole intended for wire routing. We are issuing this AD to detect and correct cracking in the fuselage frames and frame reinforcements, which could reduce the structural capability of the frames to sustain limit loads, and result in cracking in the fuselage skin and subsequent rapid depressurization of the airplane. \n\n\nDATES: This AD is effective September 23, 2009. \n\tThe Director of the Federal Register approved the incorporation by reference of a certain publication listed in the AD as of April 15, 2009 (74 FR 10469, March 11, 2009). \n\tWe must receive comments on this AD by November 9, 2009.
2014-15-20: We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model DHC-8-400 series airplanes. This AD was prompted by reports of failure of the high pressure shutoff valves (HPSOVs) causing the timer and monitor unit (TMU) to become inoperative since the HPSOV and the TMU are on the same circuit breaker. This AD requires a wiring modification to segregate the HPSOV power supply from the TMU. We are issuing this AD to prevent an inoperative TMU, which could result in the loss of the automatic de-icing mode, and lead to an increased workload for the flight crew and loss of control of the airplane.
2014-16-01: We are adopting a new airworthiness directive (AD) for MD Helicopters, Inc. (MDHI), Model MD900 helicopters. This AD requires an eddy current inspection of the main rotor upper hub assembly (upper hub) for a crack and replacing the upper hub with an airworthy upper hub before further flight if there is a crack. This AD is prompted by a report of cracks on an upper hub at the blade attach holes. The actions specified by this AD are intended to detect a crack in the upper hub to prevent failure of the upper hub and subsequent loss of control of the helicopter.
69-01-02: 69-01-02 VICKERS VISCOUNT: Amendment 39-704. Applies to Vickers Viscount Models 744, 745D, and 810 Series Airplanes incorporating Rotax Alternators N.0501, N.0502, N.0503, N.0505, N.0506, N.0507, N.0509, N.0510 and N.0511 installed on Viscount Models 744, 745D and 810 Series Airplanes. Compliance required within the next 1250 hours' time in service after the effective date of this AD, unless already completed. To prevent a fire hazard due to rubbing of the rotor shaft on the magnesium housing, in the event of a collapsed bearing, install liner Rotax P/N N.141715/1 in the main housing assembly in accordance with Rotax Modification No. 3599B, dated May 17, 1968, or later ARB approved issue or an equivalent approved by the Chief, Aircraft Certification Staff, Europe, Africa and Middle East Region. This amendment becomes effective February 1, 1969.
2014-07-51: We are publishing a new airworthiness directive (AD) for certain AgustaWestland S.p.A. Model AB139 and AW139 helicopters. This AD requires repetitively inspecting the Main Rotor (M/R) Rotating Scissors for play of the Lower Half Scissor Spherical Bearing (bearing) and removing the bearing if there is play beyond allowable limits. This AD also requires removing all affected bearings. This AD is prompted by reports of certain bearings dislodging from certain M/R Rotating Scissors. These actions are intended to detect excessive play of the bearing and prevent failure of the M/R Rotating Scissors and subsequent loss of control of the helicopter.
2014-13-12: We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This AD was prompted by reports of silicon particles inside the oxygen generator manifolds, which had chafed from the mask hoses during installation onto the generator outlets. This AD requires identifying the part number and serial number of each passenger oxygen container, replacing the oxygen generator manifold of any affected oxygen container with a serviceable manifold, and performing an operational check of the manual mask release, and corrective actions if necessary. We are issuing this AD to detect and correct non-serviceable oxygen generator manifolds, which could reduce or block the oxygen supply and result in injury to passengers when oxygen supply is needed.
68-25-02: 68-25-02\tBOEING: Amendment 39-689. Applies to all Model B737 Series Airplanes. \n\tCompliance required as indicated: \n\t(1)\tPrior to next flight, unless already accomplished, use a screwdriver to assure that mounting screws holding M360 printed circuit card are tight. \n\t(2)\tIf screws holding M360 printed circuit card are not tight, replace NAS 1068 nutplates with self-locking nuts NAS 679A08W. \n\t(3)\tWithin the next 50 hours' time in service after the effective date of this AD, unless previously accomplished, replace NAS 1068 nutplates with self-locking nuts NAS 679A08W and make certain that receptacle D1136 is secure. \n\t(4)\tWithin the next 400 hours' time in service after the effective date of this AD, unless already accomplished, modify the interphone power circuits to separate the captain's and first officer's power sources and provide dual power sources to each interphone system in accordance with the section entitled "II. Accomplishment Instructions", of Boeing Service Bulletin 24-1009, Revision 1, November 8, 1968, or later FAA approved revision thereof, or an equivalent modification approved by the Chief, Aircraft Engineering Division, FAA Western Region. \n\tThis amendment becomes effective, insofar as compliance requirements (1), (2) and (3) are concerned, upon publication in the FEDERAL REGISTER for all persons except those to whom these requirements were made effective immediately by telegram dated November 1, 1968. \n\tThis amendment becomes effective, insofar as compliance requirement (4) is concerned, for all persons on December 10, 1968.
2009-11-13: We are adopting a new airworthiness directive (AD) for certain Learjet Model 45 airplanes. For certain airplanes, this AD requires repetitive inspections for chafing and other damage of the case drain tube from the hydraulic pump case installed on the left-hand engine, and corrective action if necessary. This AD also requires, for all airplanes, repetitive inspections for discrepancies of the left engine's nacelle tubing, repetitive inspections for evidence of fluid leakage within the left engine accessory compartment, and corrective actions if necessary. This AD was prompted by reports of chafed hydraulic tubes in the left-hand engine. We are issuing this AD to detect and correct chafed hydraulic tubes in the left-hand engine and consequent hydraulic tube failure and uncontrolled loss of flammable fluid within the engine cowling, which could result in a fire in the engine nacelle and loss of control of the airplane.