Results
2022-09-10: The FAA is adopting a new airworthiness directive (AD) for all Rolls-Royce Deutschland Ltd & Co KG (RRD) RB211 Trent 875-17, 877-17, 884-17, 884B-17, 892-17, 892B-17, and 895-17 model turbofan engines. This AD was prompted by findings during engine overhaul of corrosion on the low-pressure compressor (LPC) front case assembly. This AD requires inspection of the LPC front case assembly and, depending on the result of the inspection, accomplishment of the applicable corrective action(s), as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2007-15-08: The FAA is superseding an existing airworthiness directive (AD), which applies to all BAE Systems (Operations) Limited Model ATP airplanes. The existing AD currently requires revising the Airworthiness Limitations Section (ALS) of the Instructions for Continued Airworthiness (ICA) to incorporate life limits for certain items and inspections to detect fatigue cracking in certain structures; to incorporate new inspections to detect fatigue cracking of certain significant structural items (SSIs); and to revise life limits for certain equipment and various components. This new AD requires revising the ALS of the ICA to include revised requirements. This AD results from the determination that additional and revised inspections of the fuselage are needed. We are issuing this AD to detect and correct fatigue cracking of certain structural elements, which could result in reduced structural integrity of the airplane and consequent rapid decompression of the airplane.
2022-06-06: The FAA is superseding Airworthiness Directive (AD) 2017-14- 13, which applied to certain The Boeing Company Model 737-600, -700, - 700C, -800, -900, and -900ER series airplanes. AD 2017-14-13 required a torque check of the screws in the cover assembly of the heel rest for both the captain's and the first officer's rudder pedals, and corrective action if necessary. This AD was prompted by a report of an aborted takeoff because the rudder pedals were not operating correctly, and subsequent reports of loose rudder pedal cover fasteners on airplanes on which the actions required by AD 2017-14-13 were done and on additional airplanes that were not included in the applicability of AD 2017-14-13. This AD requires modifying the rudder pedal cover and shroud assemblies, and applies to all The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes and Model 737-8 and 737-9 airplanes. This AD also limits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.
2007-14-02: The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model CL-600-1A11 (CL-600), CL-600-2A12 (CL-601), and CL-600-2B16 (CL-601-3A, CL-601-3R, and CL-604) airplanes. This AD requires inspecting to identify the part number and serial number of the selector valves of the nose landing gear (NLG) and the nose gear door, and doing related investigative and corrective actions if necessary. This AD results from reports of uncommanded partial retractions of the NLG. We are issuing this AD to prevent internal leakage of the selector valve, which, under certain conditions, could result in an uncommanded retraction of the NLG with consequent damage to the airplane and possible serious injury to ground personnel.
2022-10-04: The FAA is adopting a new airworthiness directive (AD) for certain Engine Alliance (EA) GP7270, GP7272, and GP7277 model turbofan engines. This AD was prompted by a manufacturer investigation that revealed certain stages 7-9 compressor rotor spools were manufactured from a billet of material suspected of having foreign material embedded. This AD requires the replacement of the affected stages 7-9 compressor rotor spool. The FAA is issuing this AD to address the unsafe condition on these products.
2007-14-04: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: To prevent the rudder trim tab upper pivot hole in the rudder rib flogging out, which may lead to aerodynamic flutter and possible loss of aircraft control * * * We are issuing this AD to require actions to correct the unsafe condition on these products.
2022-08-16: The FAA is superseding Airworthiness Directive (AD) 2020-20-07 for certain Rolls-Royce Deutschland Ltd & Co KG (RRD) Trent 1000-AE3, Trent 1000-CE3, Trent 1000-D3, Trent 1000-G3, Trent 1000-H3, Trent 1000-J3, Trent 1000-K3, Trent 1000-L3, Trent 1000-M3, Trent 1000-N3, Trent 1000-P3, Trent 1000-Q3, Trent 1000-R3, Trent 7000-72, and Trent 7000-72C model turbofan engines. AD 2020-20-07 required initial and repetitive borescope inspections (BSIs) or visual inspections of the intermediate-pressure compressor (IPC) shaft assembly and, depending on the results of the inspection, replacement of the IPC shaft assembly. This AD was prompted by the manufacturer providing optional terminating actions for the required repetitive inspections and alternative inspection instructions. This AD continues to require initial and repetitive BSIs but allows modification of the engine in accordance with RRD service information as a terminating action to these inspections, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2007-13-16: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: It has been determined that the surface roughness of the wing stub safety walks Series 300, gray color (equals sandpaper grid 40), installed during production on some aeroplane S/Ns, adversely affects the aircraft single engine climb performance. We are issuing this AD to require actions to correct the unsafe condition on these products.
2007-13-15: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: To prevent unchecked corrosion developing on the wing spars due to access for inspections being difficult under normal maintenance practices, which could lead to an unsafe condition and possibly a catastrophic failure of the wing * * * We are issuing this AD to require actions to correct the unsafe condition on these products.
2022-08-15: The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Deutschland GmbH (AHD) Model MBB-BK 117 C-2 helicopters. This AD was prompted by a report of restricted collective lever movement caused by entanglement of the emergency flashlight strap with the cargo hook emergency release lever, causing the emergency flashlight to leave its seat. This AD requires replacing each affected emergency flashlight with a serviceable part, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2007-13-13: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an airworthiness authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as an obstruction at the cargo compartment fire extinguisher system drier metering unit (DMU) inlet, affecting the system effectiveness and, consequently, making the fire extinguishing capability at those compartments inadequate should a fire erupt. We are issuing this AD to require actions to correct the unsafe condition on these products.
2022-08-01: The FAA is superseding Airworthiness Directive (AD) 2020-22-01 which applied to all Airbus Helicopters Model AS332C, AS332C1, AS332L, and AS332L1 helicopters. AD 2020-22-01 required inspecting the affected parts and associated frame bores for discrepancies, applicable corrective actions, and reporting certain information if necessary. This AD was prompted by reports of corrosion on attachment screws and fittings fastening the main gearbox (MGB) suspension bars to the fuselage. This AD retains the requirements of AD 2020-22-01, adds recurring inspections, and updates the applicable service information. The FAA is issuing this AD to address the unsafe condition on these products.
2007-13-08: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an airworthiness authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as a fire in the auxiliary power unit air intake. We are issuing this AD to require actions to correct the unsafe condition on these products.
2007-13-05: The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 777 airplanes. This AD requires repetitive measurements of the freeplay of the right and left elevators, rudder, and rudder tab, and related investigative and corrective actions if necessary. This AD also requires repetitive lubrication of the elevator, rudder, and rudder tab components. This AD results from reports of freeplay-induced vibration of unbalanced control surfaces. Excessive freeplay of control surfaces can cause unacceptable airframe vibration during flight. The potential for vibration of the control surface should be avoided because the point of transition from vibration to divergent flutter is unknown. We are issuing this AD to prevent flutter, which can cause damage to the control surface structure and consequent loss of control of the airplane.
2022-07-09: The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model AS33L2 and EC225LP helicopters. This AD was prompted by a discrepancy in the rotorcraft flight manual (RFM) where the rotorcraft stay-up flying capabilities for Category B operation were provided through performance data only, not as airworthiness limitations that are dependent upon on the number of passengers on board. This AD requires revising the existing RFM for your helicopter, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2007-13-03: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: It has been found that the refueling line inside the ventral fuel tank on the Embraer EMB-145XR aircraft model is not protected in accordance with SFAR-88 (Special Federal Aviation Regulation 88) requirements. The unsafe condition is potential ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tank explosions and consequent loss of the airplane. We are issuing this AD to require actions to correct the unsafe condition on these products.
2007-13-04: The FAA is superseding an existing airworthiness directive (AD), which applies to all Boeing Model 747-400, -400D, and -400F series airplanes. That AD currently requires revising the airplane flight manual (AFM) to require the flightcrew to maintain certain minimum fuel levels in the center fuel tanks, and to prohibit the use of the horizontal stabilizer fuel tank. This new AD requires installing new integrated display system (IDS) software; and also requires revising the AFM to include procedures to prevent dry operation of the center wing and horizontal stabilizer fuel tanks, for maintaining minimum fuel levels, and for de-fueling fuel tanks. For certain airplanes, this new AD also requires removing certain program pin ground wires of the IDS. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to reduce the potential for ignition sources inside fuel tanks, which, in combination with flammable fuel vapors, could result in fuel tankexplosions and consequent loss of the airplane.
2007-12-24: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: Shortly after an engine change, the aluminium fitting attached to the engine gearbox holding lines and fittings of the propeller control system was found to be cracked. This led to a pressure loss in the propeller control system following a control system malfunction and led to an in-flight engine shutdown. The broken fitting is part of the engine installation and was initially a steel part. It was later modified by the engine manufacturer to an aluminium design. Investigation determined that the area is critical for cracks due to combination of mass, material and installation torque values. Diamond Aircraft Industries incorporated with DesignChange M[Auml]M 42-184 an additional bracket into production airplanes to improve the installations and prevent vibration cracks. We are issuing this AD to require actions to correct the unsafe condition on these products.
2022-06-08: The FAA is superseding Airworthiness Directive (AD) 2017-18- 10, which applied to certain Diamond Aircraft Industries GmbH (DAI) Model DA 42, DA 42 M-NG, and DA 42 NG airplanes. AD 2017-18-10 required modifying the flap control system, repetitively inspecting the flap bell crank, and replacing the flap bell crank as necessary. Since the FAA issued AD 2017-18-10, the European Union Aviation Safety Agency (EASA) superseded its mandatory continuing airworthiness information (MCAI) to correct an unsafe condition on these products. This AD retains the actions required by AD 2017-18-10, expands the applicability, and prohibits the installation of certain flap bell cranks. The FAA is issuing this AD to address the unsafe condition on these products.
2007-12-22: This amendment adopts a new airworthiness directive (AD) for the specified Eurocopter France (ECF) model helicopters that requires replacing the hydraulic fluid at a specified time interval when operating in cold weather. This amendment is prompted by reports of ice forming due to condensation in some parts of the hydraulic system during cold weather operation. The actions specified by this AD are intended to prevent ice from forming in the hydraulic system resulting in an unintended movement of the flight controls and subsequent loss of control of the helicopter.
2007-12-15: The FAA is superseding an existing airworthiness directive (AD) for GE CF34-10E series turbofan engines. That AD currently requires removing the fuel inlet strainer from main fuel pump (MFP) part number (P/N) 2043M12P03, installing a certain replacement flange as an interim repair, remarking the MFP to P/N 2043M12P04, and performing initial and repetitive visual inspections of the main fuel filter. This AD requires removing MFPs, P/Ns 2043M12P03, 2043M12P04, 837600-3, and 837600-4, from service and installing an improved MFP with a different P/N. This AD results from GE determining that the cause of MFP fuel strainer failure is a design problem with the strainer. We are issuing this AD to prevent engine in-flight shutdown due to MFP malfunctions.
2007-12-06: We are adopting a new airworthiness directive (AD) that supersedes AD 2006-23-02, which applies to certain Hawker Beechcraft Corporation (HBC) (Type Certificate (TC) No. 3A20 and TC No. A24CE formerly held by Raytheon Aircraft Corporation and Beech) Models C90A, B200, B200C, B300, and B300C airplanes. AD 2006-23-02 currently requires you to inspect the flight controls for improper assembly or damage, and if any improperly assembled or damaged flight controls are found, take corrective action. Since we issued AD 2006-23-02, we have determined the need to add airplane serial numbers that were not previously included in the applicability. Consequently, this AD retains the actions of AD 2006-23-02 and adds airplane serial numbers to the applicability. We are issuing this AD to detect and correct improperly assembled or damaged flight controls, which could result in an unsafe condition by reducing capabilities of the flight controls and lead to loss of control.
2022-06-20: The FAA is superseding Airworthiness Directive (AD) 2020-20- 06, which applied to certain Bell Helicopter Textron Canada Limited (now Bell Textron Canada Limited) Model 429 helicopters. AD 2020-20-06 required repetitive inspections of certain cyclic and collective assembly bearings. This AD was prompted by new bellcrank assemblies, which have been upgraded with corrosion resistant steel bearings. This AD retains certain requirements of AD 2020-20-06, and depending on the inspection results, requires removing certain parts from service and installing the upgraded cyclic and collective bellcrank assemblies. This AD also requires installing the upgraded collective and cyclic bellcrank assemblies on certain helicopters if not already installed, and prohibits installing certain bellcrank assemblies. The FAA is issuing this AD to address the unsafe condition on these products.
2007-12-14: The FAA is adopting a new airworthiness directive (AD) for all Boeing Model 727 airplanes. This AD requires repetitive inspections for cracks of the body skin, doubler, and bear strap at the forward edge of the upper and lower hinge cutouts of the forward entry door, related investigative actions, and corrective action if necessary. This AD also requires a preventive modification. This AD results from reports of skin and bear strap cracks at hinge cutouts of the forward entry door. We are issuing this AD to detect and correct cracks in the skin, doubler, and bear strap at the hinge cutouts of the forward entry door, which could result in rapid decompression of the airplane.
2022-06-09: The FAA is superseding Airworthiness Directive (AD) 2019-03-01 and AD 2021-05-51 for certain Pratt & Whitney Division (PW) PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 model turbofan engines. AD 2019-03-01 required performing initial and repetitive thermal acoustic image (TAI) inspections for cracks in certain 1st- stage low-pressure compressor (LPC) blades and removal of those blades that fail inspection. AD 2021-05-51 required performing a one-time TAI inspection for cracks in certain 1st-stage LPC blades and removal of those blades that fail inspection. This AD was prompted by three in- flight failures of a 1st-stage LPC blade, with one failure resulting in an engine fire during flight, and subsequent manufacturer publication of service information specifying improved inspections for three critical locations on the 1st-stage LPC blade. This AD requires initial and repetitive ultrasonic (UT) inspections and TAI inspections for cracks in certain 1st-stage LPC blades and removal of those blades that fail inspection. The FAA is issuing this AD to address the unsafe condition on these products.