Results
2014-18-02: We are superseding Airworthiness Directive (AD) 2014-05-02 for certain The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. AD 2014-05-02 required repetitive inspections for cracking and corrosion of the aft pressure bulkhead, repetitive inspections of the frame chord drain path for debris, and corrective actions if necessary; and, for certain airplanes, enlargement of frame chord drain holes. This AD requires the same actions as AD 2014-05-02, but revises a certain repetitive inspection interval to avoid a misunderstanding of the repetitive inspection interval for the aft pressure bulkhead. This AD was prompted by reports from operators expressing confusion regarding a certain repetitive inspection interval for the aft pressure bulkhead. We are issuing this AD to detect and correct corrosion or cracking of the aft pressure bulkhead, which could result in loss of the aft pressure bulkhead web and stiffeners, and consequent rapid decompression of the airplane.
58-23-01: 58-23-01 BELL: Applies to All 47B, B3, D, D1, G, G2 and H1 Helicopters. Compliance required as indicated. Service experience indicates numerous failures of the tail rotor pitch change control bearing, P/N R4AF4 and alternate P/N's SIRP and 7R4AXIC. Failures of this bearing have been partly attributed to the pitch change control shaft being bent. To preclude the possibility of losing tail rotor control, a service life of 100 hours' time in service has been established for the tail rotor pitch change bearings P/N's R4AF4, 47-641-146-1, SIRP, and 7R4AXIC. All bearings with 90 or more hours' time in service shall be retired within the next 10 hours' time in service after the effective date of this amendment, except that tail rotor pitch change bearings with 190 or more hours' time in service as of the effective date of this amendment shall be retired prior to the accumulation of 200 hours' time in service. The bearing service life of 100 hours is predicted by the maintenance of a concentric pitch change control shaft to within the allowable tolerances. To insure straightness of the pitch change control shaft, P/N 47-641-034 or P/N 47-641-045, a 600-hour inspection for runout is required. The shaft must be inspected at the next 600-hour inspection or not later than December 15, 1958, and every 600 hours thereafter. Inspect shaft for allowable runout as follows: 1. Remove shaft from tail rotor gear box in accordance with Bell Service Manual. 2. Mount shaft at acme screw thread end in collet. 3. Measure concentricity of bearing shaft diameter. This diameter must be concentric within 0.060 TIR. 4. If diameters are not concentric within 0.060, shaft must be straightened within this tolerance. (Manufacturers Urgent Action Maintenance and Overhaul Instructions, Nos. S58-41 thru S58-47, H58-10, H58-11 and H58-12, dated October 3, 1958, cover same subjects.) Revised September 21, 1961. Revised January 18, 1963.
2014-16-23: We are superseding Airworthiness Directive (AD) 2011-16-01 for all Dassault Aviation Model FALCON 7X airplanes. AD 2011-16-01 required adding an automatic reversion logic and a means for the pilot to override pitch trim control normal modes, and installing placards in the cockpit; replacing the frame of the emergency switch box; replacing certain horizontal stabilizer electronic control units (HSECU); revising the Limitations section of the airplane flight manual (AFM); and revising the maintenance program to incorporate a certain task. This new AD requires modifying the fly-by-wire (FBW) standard; and operational testing of the electric motors reversion relays and trim emergency command of the horizontal stabilizer trim system (HSTS), and repairs if necessary. This AD was prompted by an uncontrolled pitch trim runaway during descent. We are issuing this AD to prevent an uncontrolled pitch trim runaway, which could result in loss of control of the airplane.
2014-17-07: We are adopting a new airworthiness directive (AD) for all Airbus Model A300 series airplanes; Model A300 B4-600, B4-600R, and F4- 600R series airplanes; Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes); and Model A310 series airplanes. This AD was prompted by reports of rupture of the uplock springs of the nose landing gear (NLG) and main landing gear (MLG) doors and legs. This AD requires repetitive inspections of the uplock springs of the NLG and MLG doors and legs for broken and damaged springs, and corrective actions if necessary. We are issuing this AD to detect and correct improper free fall extension of the MLG or NLG, which could lead to possible loss of control of the airplane on the ground, and consequent damage to the airplane and injury to occupants.
74-23-08: 74-23-08 GRUMMAN AMERICAN CORPORATION: Amendment 39-2007. Applies to Grumman G-159 airplanes certificated in all categories. Compliance required within the next 200 hours time in service after the effective date of this airworthiness directive unless already accomplished. To provide dual electrical power for the fire extinguisher squib circuits accomplish the following or an equivalent rework approved by the Chief, Engineering and Manufacturing Branch, Southern Region. Remove the existing left and right engine fire extinguisher switches and left hand eyebrow circuit breaker panel nameplate. Install MS24524-21 switches, electrical wiring, 159SB10112-1 nameplate and check out system in accordance with Grumman Gulfstream I Aircraft Service Change 210. This amendment becomes effective November 15, 1974.
66-22-02: 66-22-02\tBOEING: Amdt. 39-285 Part 39 Federal Register September 7, 1966. Applies to Model 727 Series Airplanes Listed in Boeing Service Bulletin No. 29-22, Dated February 21, 1966.\n \n\tCompliance required within the next 700 hours' time in service after the effective date of this AD, unless already accomplished. \n\n\tTo prevent failure of the pneumatic brake system due to leaks between the control valve and the brake housing, modify the pneumatic brake system line installation in accordance with Boeing Service Bulletin No. 29-22, dated February 21, 1966, or later FAA-approved revision, or an equivalent approved by the Chief, Aircraft Engineering Division, FAA Western Region. \n\n\tThis directive effective October 7, 1966.
2016-18-02: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 777-200 and -300ER series airplanes. This AD requires replacing the low-pressure oxygen flex hoses with new non- conductive low-pressure oxygen flex hoses in the gaseous passenger oxygen system in airplanes equipped with therapeutic oxygen. This AD was prompted by a determination that the low-pressure oxygen flex hoses in the gaseous passenger oxygen system can potentially be conductive. We are issuing this AD to prevent electrical current from passing through the low-pressure oxygen flex hoses in the gaseous passenger oxygen system, which can cause the flex hoses to melt or burn, and a consequent oxygen-fed fire in the passenger cabin.
2014-16-26: We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model FALCON 900EX airplanes. This AD was prompted by our determination to introduce a corrosion prevention control program, among other changes, to the maintenance requirements and airworthiness limitations. This AD requires revising the maintenance or inspection program, as applicable, to include the maintenance tasks and airworthiness limitations specified in the Airworthiness Limitations section of the airplane maintenance manual. We are issuing this AD to prevent reduced structural integrity and reduced controllability of the airplane.
2014-16-25: We are superseding Airworthiness Directive (AD) 2007-06-12 for certain Airbus Model A330-200 and A330-300 airplanes. This new AD reduces the compliance times for reinforcing the structure of the center fuselage. This AD was prompted by a new fatigue and damage tolerance evaluation that revealed the compliance time for an existing reinforcement of the fuselage has to be reduced. We are issuing this AD to prevent fatigue cracking of the fuselage, which could result in reduced structural integrity of the fuselage.
2014-16-05: We are adopting a new airworthiness directive (AD) for certain Embraer S.A. Model ERJ 170 airplanes. This AD was prompted by reports of ``BLEED 1(2) LEAK'' messages displayed on the engine indication and crew alert system (EICAS), and indirect damage to components of the electrical wiring interconnection system (EWIS) in the engine pylon area. This AD requires inspecting the EWIS components for damage, and repair if necessary. This AD also requires installing pre-cooler deflectors on the left- and right-hand pylons, and applying silicone sealant. We are issuing this AD to prevent indirect damage to EWIS components near the engine bleed air pre-coolers, which could result in a dual engine roll back to idle and consequent dual engine power loss and reduced controllability of the airplane.