Results
2014-06-02: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-400 series airplanes. This AD was prompted by reports of auxiliary power unit (APU) faults due to power feeder cable chafing. This AD requires detailed inspections for damage of the APU power feeder cables; replacing the clamps and installing grommets; and related investigative and corrective actions if necessary. We are issuing this AD to detect and correct chafing of the APU power feeder cables within a flammable fluid leakage zone, which, with arcing, could result in fire and structural damage.
2008-23-19: We are adopting a new airworthiness directive (AD) for certain Boeing Model 757 airplanes. This AD requires sealing the fasteners on the front and rear spars inside the left and right main fuel tanks and on the rear spar and lower panel of the center fuel tank. This AD also requires inspections of the wire bundle support installations to verify if certain clamps are installed and if Teflon sleeving covers the wire bundles inside the left and right equipment cooling system bays, on the left and right rear spars, and on the left and right front spars; and corrective actions if necessary. This AD results from a fuel system review conducted by the manufacturer. We are issuing this AD to detect and correct improper wire bundle support installation and sleeving and to prevent improperly sealed fasteners in the main and center fuel tanks from becoming an ignition source, in the event of a fault current, which could result in a fuel tank explosion and consequent loss of the airplane.
2014-05-13: We are superseding Airworthiness Directive (AD) 2004-12-07 for certain The Boeing Company Model 757 series airplanes equipped with Rolls-Royce RB211 engines. AD 2004-12-07 required modification of the nacelle strut and wing structure; and for certain airplanes, repetitive detailed inspections of certain aft bulkhead fasteners for loose or missing fasteners, and corrective action if necessary. For certain other airplanes, AD 2004-12-07 required a one-time detailed inspection of the middle gusset of the inboard side load fitting for proper alignment, and realignment if necessary; a one-time eddy current inspection of certain fastener holes for cracking, and repair if necessary; and a detailed inspection of certain fasteners for loose or missing fasteners, and replacement with new fasteners if necessary. This new AD specifies a maximum compliance time limit. This AD was prompted by reports indicating that the actual operational loads applied to the nacelle are higher than the analytical loads that were used during the initial design. We are issuing this AD to prevent fatigue cracking in primary strut structure and consequent reduced structural integrity of the strut.
2014-05-12: We are superseding Airworthiness Directive (AD) 2010-15-08 for all The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. AD 2010-15-08 required repetitive inspections for discrepancies of each carriage spindle of the outboard mid-flaps; repetitive gap checks of the inboard and outboard carriages of the outboard mid-flaps to detect fractured carriage spindles; measuring to ensure that any new or serviceable carriage spindle meets minimum allowable diameter measurements taken at three locations; repetitive inspections, measurements, and overhaul of the carriage spindles; replacement of any carriage spindle when it has reached its maximum life limit; and corrective actions if necessary. This new AD requires reducing the life limit of the carriages, reducing the repetitive interval for certain inspections and gap checks for certain carriages. This new AD also adds an option, for certain replacements, of doing an inspection, and related investigativeand corrective actions if necessary. This AD was prompted by a report of failure of both flap carriages. We are issuing this AD to detect and correct cracked, corroded, or fractured carriage spindles, which could lead to severe flap asymmetry, and could result in reduced control or loss of controllability of the airplane.
75-18-01: 75-18-01 ENTWICKLUNGSGEMEINSCHAFT (MESSERSCHMITT-BOLKOW-BLOHM GmbH): Amendment 39-2318. Applies to Phoebus A1 and B1 gliders, serial numbers 702 thru 751, certificated in all categories. Compliance is required as indicated. To prevent loss of rudder control, accomplish the following: (a) Within the next 10 hours' time in service after the effective date of this AD, unless already accomplished, and thereafter at intervals not to exceed 100 hours' time in service from the last inspection, inspect the rudder control cable lever as follows: (1) Remove headrest, luggage container, and seat. (2) Disconnect rudder control cables from cable lever. (3) Remove rudder control rod and rudder control cable lever (P/N 15120-4236). (4) Inspect rudder control cable lever weld for cracks using a magnifying glass with a magnification power of not less than five. (5) If a crack is found comply with paragraph (b) of this AD. (b) If a rudder control cable lever weld crack is found during an inspection required by paragraph (a), replace the rudder control cable lever P/N 15120-4236 with a serviceable part of the same part number or an FAA-approved equivalent. (MBB Service Bulletin No. PHOEBUS 27-20/1, dated March 1975, pertains to this AD.) This amendment becomes effective August 18, 1975.
2004-23-11: The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas Model DC-9-14 and DC-9-15 airplanes; and Model DC-9-20, DC-9-30, DC-9-40, and DC-9-50 series airplanes. This AD requires repetitive high frequency eddy current inspections to detect cracks in the vertical radius of the upper cap of the center wing rear spar, and repair if necessary. This AD is prompted by reports of cracks in the upper cap of the center wing rear spar that resulted from stress corrosion. We are issuing this AD to detect and correct cracking of the left or right upper cap of the center rear spar, which would cause a possible fuel leak and structural failure of the upper cap, and result in reduced structural integrity of the airplane.
2014-05-18: We are adopting a new airworthiness directive (AD) for all Bombardier, Inc. Model DHC-8-400 series airplanes. This AD was prompted by a report that a batch of main landing gear (MLG) door actuators with a certain part number having certain serial numbers could be assembled with the scraper installed backward. This AD requires repetitive functional checks of the MLG alternate extension system (AES) and eventual replacement of certain MLG door actuators with actuators that have either been reworked or do not have certain serial numbers. We are issuing this AD to prevent incorrectly installed scrapers, which could hinder the operation of the MLG AES, and result in failure of the MLG AES on one side, and consequent unsafe asymmetrical landing configuration.
2014-05-08: We are adopting a new airworthiness directive (AD) for certain Airbus Helicopters Model AS332L1 helicopters. This AD requires replacing the rivets on the left-hand (LH) and right-hand (RH) Y350 longitudinal beams (longitudinal beams Y350). This AD was prompted by a report that non-conforming rivets had been installed on an AS332 helicopter during a production modification. The actions of this AD are intended to prevent failure of the longitudinal beams Y350 and subsequent loss of control of the helicopter.
2014-05-15: We are adopting a new airworthiness directive (AD) for Airbus Helicopters Model AS332C, AS332L, AS332L1, AS332L2, and SA330J helicopters. This AD prohibits use of the hydraulic hoist in helicopters equipped with certain parts and configurations until a hoist beam lower fitting protector is installed. This AD was prompted by a report that the hoist cable jammed during a rescue at sea. The actions of this AD are intended to prevent the hoist cable from jamming and subsequent cable failure, which could result in injury and damage to the helicopter.
2014-05-07: We are superseding airworthiness directive (AD) 2010-11-51 for Eurocopter France (Eurocopter) Model AS350B, BA, B1, B2, C, D, and D1 helicopters and Model AS355E, F, F1, F2, and N helicopters with certain part-numbered tail gearbox (TGB) control levers installed. AD 2010-11- 51 required repetitive visual inspections of the TGB control lever for a crack and replacing a cracked TGB control lever with an airworthy TGB control lever. This new AD retains the requirements of AD 2010-11-51 and also requires inspecting other areas of the TGB control lever not previously inspected and at additional inspection intervals. This AD was prompted by several reports of cracking in a TGB control lever. The actions of this AD are intended to prevent failure of the TGB control lever, loss of tail rotor control, and subsequent loss of control of the helicopter.