Results
95-18-01: This amendment adopts a new airworthiness directive (AD) that applies to Scheibe Flugzeugbau GmbH SF34 and SF34B gliders. This action requires adding armature (supportive covering) to both wings, modifying the root rib of the left wing and incorporating changes and operating limitations to the flight manual. Failure of the left wing root rib on one of the affected gliders while in flight prompted this action. The actions specified by this AD are intended to prevent fatigue failure of the wing, which could result in loss of control of the glider.
2008-12-16: We are adopting a new airworthiness directive (AD) for certain M7 Aerospace LP SA226 and SA227 series airplanes. This AD requires you to inspect electrical wires/components, hydraulic and bleed air tube assemblies at left-hand (LH) and right-hand (RH) inboard wing leading edge/battery box areas, LH/RH wing stations 51.167 to 81.174, and at all feed-through locations into the LH/RH inboard keelson. If chafing/ arcing is found, this AD requires you to reposition, repair, and/or replace all chafed electrical wires, components, and hydraulic and bleed air tube assemblies, as required. This AD also requires you to reposition the battery lead cables, cover four-gauge wires leaving the battery box with firesleeving and secure with clamps, and protect the battery power cable. This AD results from five reports of chafing between the bleed air tube and the electrical starter cables with one incident resulting in a fire. We are issuing this AD to detect and correct chafing/arcing of electrical wires, components, and bleed air lines. This condition could result in arcing of the exposed wires and burn a hole in the bleed air line or the nearby hydraulic line, and lead to a possible hydraulic fluid leak and fire in the engine nacelle compartment.
2001-19-05: This amendment adopts a new airworthiness directive (AD) that is applicable to Rolls-Royce plc. (RR) models RB211-535C-37, RB211-535E4-37, RB211-535E4-B-37, and RB211-535E4-B-75 turbofan engines, with radial drive steady bearing, part number (P/N) LK76084. This action requires the replacement of certain radial drive steady bearings, installed in the high speed gearbox drive. This amendment is prompted by five reports of radial drive steady bearing failures. The actions specified in this AD are intended to reduce the risk of engine in-flight shutdown, due to failure at low life of radial drive steady bearings.
2020-20-03: The FAA is adopting a new airworthiness directive (AD) for certain Airbus Helicopters Model AS350B2 helicopters. This AD requires performing a test of the main rotor RPM (NR) indicator, and depending on the results, altering the wiring. This AD was prompted by reports of some NR indicators displaying incorrect information. The actions of this AD are intended to address an unsafe condition on these products.
95-17-04: This amendment supersedes an existing airworthiness directive (AD), applicable to all Jetstream Model ATP airplanes, that currently requires revising the Airplane Flight Manual (AFM) to prohibit flight in freezing precipitation conditions. This amendment adds a requirement to install modifications of the engine air intake system. This amendment is prompted by the development of modifications of the engine air intake system intended to permit operation of these airplanes in freezing precipitation conditions. The actions specified by this AD are intended to prevent engine power rollback in flight during freezing precipitation conditions.
2021-17-13: The FAA is adopting a new airworthiness directive (AD) for certain PZL Swidnik S.A. Model PZL W-3A helicopters. This AD was prompted by a report of a damaged wheel braking system pneumatic line fitting installed on the left-hand (LH) main landing gear (MLG) leg. This AD requires modifying the LH MLG leg. The FAA is issuing this AD to address the unsafe condition on these products.
2008-12-17: The FAA is superseding an existing airworthiness directive (AD), which applies to all Lockheed Model L-1011 series airplanes. That AD currently requires an inspection of the fuel level control switch, the fuel level control switch wiring harness, and the wiring harness conduit for damage, wear or chafing, broken or missing O-rings, or indications of electrical arcing. That AD also requires replacement of a certain conduit in the fuel level control switch wiring harness, installation of electrical sleeving over the fuel level control switch wiring harness, and installation of the fuel level control switch that has been so modified. This new AD requires an inspection of the fuel level control switch, wiring harnesses, and harness conduit for any visible damage, wear or chafing, broken or missing O-rings, or indications of electrical arcing; an inspection to determine the part number of the wiring harness conduit; and corrective actions if necessary. This new AD also requires replacing certain sleeving with new, improved sleeving over the wiring harness of the fuel level control switch. This AD results from a design review of the fuel tank systems. We are issuing this AD to prevent chafing of the fuel level control switch wiring harness, which could cause arcing and result in a fire in the fuel tank. DATES: This AD becomes effective July 23, 2008. The Director of the Federal Register approved the incorporation by reference of a certain other publication listed in the AD as of July 23, 2008. On June 1, 2001 (66 FR 21072, April 27, 2001), the Director of the Federal Register approved the incorporation by reference of a certain service bulletin.
2020-18-13: The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This AD was prompted by the FAA's analysis of the Model 737 fuel system reviews conducted by the manufacturer. This AD requires modifying the fuel quantity indicating system (FQIS) to prevent development of an ignition source inside the center fuel tank due to electrical fault conditions. This AD also provides alternative actions for cargo airplanes. \n\n((Page 60049)) \n\nThe FAA is issuing this AD to address the unsafe condition on these products.
95-17-01: This amendment supersedes an existing airworthiness directive (AD), applicable to certain Boeing Model 707 and 720 series airplanes, that currently requires repetitive visual and dye penetrant inspections to detect cracks in areas of the upper forward skin panels of the wing center section, and repair, if necessary. It also provides an optional terminating modification for the repetitive inspections. This amendment requires repetitive visual and eddy current inspections to detect cracks in areas of the upper forward skin panels of the wing center section, and repair, if necessary. This amendment is prompted by reports indicating that the inspections required by the existing AD are not effective in detecting fatigue cracks in a timely manner. The actions specified by this AD are intended to prevent fatigue cracking and subsequent failure of the upper forward skin panels of the wing center section.
95-12-20: This amendment adopts a new airworthiness directive (AD), applicable to certain Airbus Model A330 and A340 series airplanes. This action requires a one-time inspection to determine the torque value of all wing slat track stop pins, and correction of discrepancies. This amendment is prompted by a report of a fuel leak that was caused by an incorrectly torqued slat track stop pin that punctured the slat canister. The actions specified in this AD are intended to prevent such fuel leakage conditions, which could result in inadequate fuel for completing a flight and could pose a fire hazard.