Results
98-25-52: This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) T98-25-52 that was sent previously to all known U. S. owners and operators of all Boeing Model 747 series airplanes by individual telegrams. This AD requires revising the Airplane Flight Manual to include procedures to prevent dry operation of the center wing fuel tank override/jettison pumps and, for certain airplanes, to prohibit operation of the horizontal stabilizer tank transfer pumps in flight. This action is prompted by a report indicating that several override/jettison fuel pumps from the center wing tanks and main tanks had been removed because circuit breakers for the override/jettison fuel pumps were tripped, or low pump output pressure was indicated. The actions specified by this AD are intended to prevent contact between the rotating paddle wheel and the stationary end plates within the center wing tank override/jettison fuel pumps or horizontal stabilizer tanktransfer pumps due to excessive wear of the pump shaft carbon thrust bearing, which could cause sparks and/or a hot surface condition and consequent ignition of fuel vapor in the center wing tank or horizontal stabilizer tank during dry pump operation (no fuel flowing).
98-09-16: This amendment adopts a new airworthiness directive (AD) that is applicable to all Aerospatiale Model ATR-42 and ATR-72 series airplanes. This action requires revising the Airplane Flight Manual (AFM) to add specific flightcrew instructions to be followed in the event of failure of one or both of the direct current (DC) generators. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified in this AD are intended to prevent failure of the second of two DC generators after the failure of the first generator, which could lead to the loss of main battery power and result in the loss of all electrical power, except the emergency battery supply, during flight.
2009-18-07: The FAA is superseding an existing airworthiness directive (AD), which applies to certain Boeing Model 747 series airplanes. That AD currently requires repetitive inspections to detect cracks in various areas of the fuselage internal structure, and related investigative/corrective actions if necessary. This new AD requires additional repetitive inspections for cracking of certain fuselage structure, and related investigative/corrective actions if necessary. This AD results from fatigue tests and analysis by Boeing that identified areas of the fuselage where fatigue cracks can occur. We are issuing this AD to prevent the loss of the structural integrity of the fuselage, which could result in rapid depressurization of the airplane.
98-26-08: This amendment adopts a new airworthiness directive (AD), applicable to certain McDonnell Douglas Model DC-9-10, -20, -30, -40, and -50 series airplanes, and C-9 (military) airplanes, that requires a one-time visual inspection to determine if all corners of the doorjamb of the forward service door have been previously modified. The action also requires various repetitive inspections to detect cracks of the fuselage skin and doubler at all corners of the doorjamb of the forward service door, and to detect cracks on the skin adjacent to the modification; and various follow-on actions. This amendment is prompted by reports of fatigue cracks found in the fuselage skin and doubler at the corners of the doorjamb of the forward service door. The actions specified by this AD are intended to detect and correct such fatigue cracking, which could result in rapid decompression of the fuselage and consequent reduced structural integrity of the airplane.
56-19-01: 56-19-01 de HAVILLAND: Applies to All Model 104 "Dove" Aircraft. Compliance required as indicated below. A case has occurred in which the mild steel rivet locking the stud, P/N 4CF.607 to the spindle, P/N 4CF.603ND in the aileron differential pulley assembly has sheared, allowing the spindle to unscrew from the stud to such an extent that it, together with the pulley, was on the point of becoming disengaged from the pulley bracket. To prevent a recurrence of this defect, compliance with Dove Modification No. 765 (installation of a H.T.S. pin for locking stud on aileron differential pulley spindle) is considered mandatory by the British Air Registration Board in which the FAA concurs. Accordingly, unless already accomplished, Modification No. 765 should be embodied on all Dove aircraft as soon as possible, but not later than October 15, 1956. (Dove Modification 765 is covered in de Havilland Service Technical News Sheet CT (104) No. 114 dated November 1, 1954.)This supersedes AD 55-02-01.
98-26-07: This amendment adopts a new airworthiness directive (AD), applicable to Rolls-Royce Limited, Bristol Engines Division,(R-R) Viper Models Mk.521 and Mk.522 turbojet engines, that requires replacement of certain high pressure (HP) fuel pumps with an improved design which is more tolerant of reduced lubricity fuel caused by water contamination. This amendment is prompted by reports of HP fuel pump drive shaft failures resulting in in-flight engine shutdowns. These failures have been attributed to the reduced lubricity properties of fuel which is contaminated by water. The actions specified by this AD are intended to prevent HP fuel pump failures, which can result in an in-flight engine shutdown. The incorporation by reference of certain publications listed in the regulations is approved by the Director of the Federal Register as of February 16, 1999.
2019-11-02: The FAA is superseding Airworthiness Directive (AD) 2017-16- 10, which applied to all The Boeing Company Model 777 airplanes. AD 2017-16-10 required repetitive inspections of the left and right side underwing longerons for any crack, and related investigative and corrective actions if necessary. This AD retains the requirements of AD 2017-16-10, reduces certain compliance times for certain airplanes, and removes airplanes from the applicability. This AD was prompted by reports of cracks on the underwing longerons. The FAA is issuing this AD to address the unsafe condition on these products.
2007-17-06: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: A nose landing gear leg failed in area of the nose gear leg pivot axle. This airplane was mostly operated on grass runways and training operations. This failure was based on a fatigue crack developed in the pivot axle. Material inspections figured out that this cracks may also develop on other serial No. pending the type of operation. We are issuing this AD to require actions to correct the unsafe condition on these products.
2019-12-01: The FAA is adopting a new airworthiness directive (AD) for certain CFM International S.A. (CFM) LEAP-1B21, -1B23, -1B25, -1B27, - 1B28, -1B28B1, -1B28B2, -1B28B3, -1B28B2C, -1B28BBJ1, and -1B28BBJ2 model turbofan engines. This AD requires initial and repetitive inspections of the transfer gearbox (TGB) scavenge screens and, depending on the results of the inspection, possible removal of the engine from service. This AD was prompted by multiple reports of in- flight shutdowns (IFSDs) due to radial drive shaft (RDS) bearing failure. The FAA is issuing this AD to address the unsafe condition on these products.
2001-24-31: This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 747 series airplanes, that requires performing a one-time inspection for chafing of certain electrical wire bundles behind the flight engineer's panel in the cockpit; repairing any chafed wire bundles, if necessary; and installing Teflon sleeving over the inspected wire bundles and rerouting them. This action is necessary to prevent burning of electrical wires, which could result in smoke in the cockpit and loss of function of several airplane systems. This action is intended to address the identified unsafe condition.