Results
89-10-08: 89-10-08 AEROSPATIALE: Amendment 39-6205. Applicability: Model ATR-42 series airplanes, Serial Numbers 003 through 093, certificated in any category. Compliance: Required as indicated, unless previously accomplished. To prevent improper functioning of Honeywell-Sperry navigation equipment and to prevent incompatible combinations of this equipment, accomplish the following: A. Within 10 days after the effective date of this AD, accomplish the following in accordance with Aerospatiale Service Bulletin ATR42-34-0027, dated April 6, 1988: 1. Inspect Honeywell-Sperry Symbol Generator Units (SGU) for unauthorized mixing of units in accordance with paragraph C.(1) of the service bulletin. Correct any unauthorized mixing of units prior to further flight. 2. Inspect Honeywell-Sperry navigation equipment for unauthorized mixing of Attitude Heading Reference Units (AHRU) and SGU in accordance with paragraphs C.(2) and C.(3) of the service bulletin. For airplanes with unauthorized mixing of AHRU and SGU, prior to further flight, insert the following into the Limitations Section 2 of the Airplane Flight Manual (AFM). This can be accomplished by inserting a copy of this AD into the AFM and into the Flight Crew Operations Manual: "Approach operations are limited to Category 1 or higher weather minima." Operate the airplane in accordance with this limitation until the requirements of paragraph B. of this AD are accomplished, at which time this limitation may be removed from the AFM. B. Within 120 days after the effective date of this AD, accomplish the following: 1. Replace the Digital Air Data Computer (DADC), in accordance with Aerospatiale Service Bulletin ATR42-34-0024, Revision 1, dated August 30, 1988. 2. Replace the Attitude Heading Reference System (AHRS), in accordance with Aerospatiale Service Bulletin ATR42-34-0025, Revision 1, dated August 30, 1988. 3. Replace the Symbol Generator Units (SGU),in accordance with Aerospatiale Service Bulletin ATR42-34-0026, Revision 1, dated August 30, 1988. C. An alternate means of compliance or adjustment of the compliance time, which provides an acceptable level of safety, may be used when approved by the Manager, Standardization Branch, ANM-113, FAA, Northwest Mountain Region. NOTE: The request should be forwarded through an FAA Principal Maintenance Inspector (PMI), who may add any comments and then send it to the Manager, Standardization Branch, ANM-113. D. Special flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate airplanes to a base for the accomplishment of the requirements of this AD. All persons affected by this directive who have not already received the appropriate service documents from the manufacturer may obtain copies upon request to Aerospatiale, 316 Route de Bayonne, 31060 Toulouse, Cedex 03, France. These documents may be examined at the FAA, Northwest Mountain Region, Transport Airplane Directorate, 17900 Pacific Highway South, Seattle, Washington, or at the Seattle Aircraft Certification Office, 9010 East Marginal Way South, Seattle, Washington. This amendment (39-6205, AD 89-10-08) becomes effective on June 9, 1989.
95-08-06: This amendment adopts a new airworthiness directive (AD), applicable to certain Raytheon Corporate Jets Models DH/BH/HS/BAe 125-1A to -700A series, BAe 125-800A, and Hawker 800 series airplanes, that requires replacement of the existing standby static inverter with an inverter that incorporates a circuit board assembly sealed with a conformal coating. This amendment is prompted by reports of failure of the standby static inverter caused by electrical shorting from moisture condensing on the printed circuit boards (PCB), due to aberrations in the PCB conformal coating. The actions specified by this AD are intended to prevent malfunction of the standby static inverter due to exposure to moisture caused by inadequate insulation coating of the circuit board assembly. Malfunction or failure of the standby static inverter, when its use is necessary, could result in the loss of electric power for certain equipment critical to safety of flight.
2008-09-02: We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: Further to a new fracture in flight of a CAP 10B wing in June 2003, the investigation in process seems to point out that a wrong application of CAP 10B Service Bulletin No. 16 (CAP 10B-57-004) would lead to the impossibility of detecting the potential spar damage while performing the Type Certificate holder upper spar flange inspection. We are issuing this AD to require actions to correct the unsafe condition on these products. DATES: This AD becomes effective May 27, 2008. On May 27, 2008, the Director of the Federal Register approved the incorporation by reference of APEX Aircraft Document No. 1000913GB, dated February 4, 2002; APEXAircraft Document No. 1000914GB, dated February 4, 2002; and APEX Aircraft Document No. 1000915GB, dated February 4, 2002, listed in this AD. As of July 23, 1993 (58 FR 31342, June 2, 1993), the Director of the Federal Register approved the incorporation by reference of Avions Mudry & CIE Service Bulletin CAP 10B No. 16, dated April 27, 1992, listed in this AD.
2001-16-14: This amendment adopts a new airworthiness directive (AD) that is applicable to certain Airbus Model A319, A320, and A321 series airplanes. This action requires modification of the telescopic girt bar of the escape slide/raft assembly, and follow-on actions. This action is necessary to prevent failure of the escape slide/raft to deploy correctly, which could result in the slide being unusable during an emergency evacuation and consequent injury to passengers or airplane crewmembers. This action is intended to address the identified unsafe condition.
2020-15-05: The FAA is superseding Airworthiness Directive (AD) 2018-18-02 for certain Austro Engine GmbH model E4 engines and all Austro Engine GmbH model E4P engines. AD 2018-18-02 required replacement of the timing chain and amending certain airplane flight manuals (AFMs) to limit the use of windmill restarts. This AD requires amendment of certain existing AFMs to limit the use of windmill restarts and removes the timing chain replacement requirement in AD 2018-18-02. This AD was prompted by reports of considerable wear of the timing chain on the affected engines. The FAA is issuing this AD to address the unsafe condition on these products.
2008-08-22: We are adopting a new airworthiness directive (AD) for certain Boeing Model 737-600, -700, -700C, -800, and -900 series airplanes. This AD requires a one-time inspection to determine the material of the forward and aft gray water drain masts. For airplanes having composite gray water drain masts, this AD requires installation of a bonding jumper between a ground and the clamp on the tube of the forward and aft gray water composite drain masts. This AD results from a report of charred insulation blankets and burned wires around the forward gray water composite drain mast found during an inspection of the forward cargo compartment on a Model 767-300F airplane. We are issuing this AD to prevent a fire near a composite drain mast and possible disruption of the electrical power system caused by a lightning strike on a composite drain mast, which could result in the loss of several functions essential for safe flight.
95-07-02: This amendment adopts a new airworthiness directive (AD), applicable to AlliedSignal Inc. (formerly Garrett Turbine Engine Company) TFE731-3 series turbofan engines, that requires the removal of suspect low pressure turbine (LPT) disks due to their susceptibility to creep fatigue. This amendment is prompted by reports of LPT disks that have separated through the disk web due to creep fatigue. The actions specified by this AD are intended to prevent an LPT disk web separation, which may result in an uncontained engine failure and damage to the aircraft.
2008-08-21: The FAA is superseding an existing airworthiness directive (AD), which applies to all EMBRAER Model ERJ 170-100 LR, -100 SE, -100 STD, and -100 SU airplanes; and Model ERJ 190-100 IGW, -100 LR, and - 100 STD airplanes. That AD currently requires revising the Limitations section of the airplane flight manual (AFM) to prohibit the flightcrew from moving the throttle into the forward thrust range immediately after applying the thrust reverser. This new AD adds additional airplanes to the applicability and requires the AFM revision for those additional airplanes. For certain airplanes, this AD also requires installing new, improved full-authority digital engine-control (FADEC) software. This AD results from a report that, during landing, the thrust reverser may not re-stow completely if the throttle lever is moved into the forward thrust range immediately after the thrust reverser is applied. We are issuing this AD to prevent the flightcrew from performing a takeoff with a partially deployed thrust reverser, which could result in reduced controllability of the airplane.
2001-16-05: This amendment supersedes an existing airworthiness directive (AD) that is applicable to Rolls-Royce plc. (RR) RB211 Trent 768-60, Trent 772-60, and Trent 772B-60 turbofan engines. That AD currently requires the removal of low pressure compressor (LPC) fan blades, initial and repetitive ultrasonic inspections for cracks in LPC fan blade dovetail roots, and if necessary, replacement with serviceable parts. This amendment requires earlier initial and more frequent repetitive ultrasonic inspections of LPC fan blades, with inspection thresholds and intervals specified by engine model. This amendment is prompted by data collected by RR, that identifies the need to inspect LPC fan blade dovetail roots at an earlier initial threshold and at more frequent intervals than is required by the existing AD. The actions specified in this AD are intended to prevent possible multiple LPC fan blade failures, which could result in an uncontained engine failure and damage to the airplane.
2020-15-03: The FAA is superseding Airworthiness Directive (AD) 2016-07-13 and AD 2018-03-22 which apply to certain GE Aviation Czech s.r.o. M601D-11, M601E-11, M601E-11A, M601E-11AS, M601E-11S, and M601F model turboprop engines. AD 2016-07-13 required inspection of the engine power turbine (PT) disk and, if found damaged, its replacement with a part eligible for installation. AD 2018-03-22 required the removal of certain engine PT disks identified by part number (P/N) installed on the affected engines. This AD requires an inspection of the engine PT disk and, if found damaged, its replacement with a part eligible for installation. This AD also requires the removal of certain engine PT disks identified by P/N installed on the affected engines. This AD was prompted by the discovery of damage to certain engine PT disks and a review by the manufacturer that determined that certain engine PT rotors have less overspeed margin than originally declared during product certification. This AD was also prompted by the manufacturer identifying additional P/Ns and serial numbers (S/Ns) of engine PT disks affected by damage or non-conformity since publishing AD 2016-07- 13 and AD 2018-03-22. The FAA is issuing this AD to address the unsafe condition on these products.