Results
2008-11-11: We are superseding an existing airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: Cracks have been reported in the front spar center web of the tailplane at the pick-up bracket and at lightening holes. If not detected early and repaired, these cracks may lead to failure of the tailplane. We are issuing this AD to require actions to correct the unsafe condition on these products.
2005-06-02: The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 757-200 series airplanes. This AD requires modifying the wiring of the test ground signal for the master dim and test system circuit in the flight compartment. This AD is prompted by a report that the master dim and test system circuit does not have wiring separation of the test ground signal for redundant equipment in the flight compartment. We are issuing this AD to prevent a single fault failure during flight, which could result in test patterns instead of the selected radio frequencies showing on the communications panel. These conditions could adversely affect voice and transponder communication capability between the flightcrew and air traffic control, which could result in increased pilot workload.
95-16-07: This amendment supersedes an existing airworthiness directive (AD), applicable to Pratt & Whitney JT8D series turbofan engines, that currently requires initial and repetitive inspections of 9th through 12th stage high pressure compressor (HPC) disks at the tierod holes. This amendment eliminates an optional on-wing ultrasonic inspection of the 10th stage high pressure compressor (HPC) disk. This amendment is prompted by a report of an uncontained failure of a 10th stage HPC disk that was previously inspected using the on-wing ultrasonic inspection method. The actions specified by this AD are intended to prevent uncontained fractures of 9th through 12th stage HPC disks and engine failure.
2008-12-18: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: During a flight test performed on an EASy aircraft, subsequently to an air data probe failure, the crew realized that the Flight path vectors and the Vertical speeds that were displayed on pilot's and co-pilot's PDU (primary display unit) were identically wrong. A review of the EASy architecture reveals that * * * One single ADS (air data system) unflagged air data error may lead to the computation and display on both pilot's and co-pilot's display units of unnoticed and misleading flight information. At take-off or during go-around this situation might considerably reduce flight safety. We are issuing this AD to require actions to correctthe unsafe condition on these products.
2001-19-03: This amendment adopts a new airworthiness directive (AD), that is applicable to Rolls-Royce Corporation (formerly Allison Engine Company) Model AE 3007A and AE 3007C turbofan engines with a certain part number high pressure turbine (HPT) 1st to 2nd stage turbine spacer installed. This amendment requires removal and replacement of that HPT 1st to 2nd stage turbine spacer before it reaches its new reduced engine cycle life limit.This amendment is prompted by the results of a detailed component analysis that indicates that the HPT 1st to 2nd stage turbine spacer stresses are higher than predicted. The actions specified by this AD are intended to prevent HPT 1st to 2nd stage turbine spacer failure which could result in an uncontained engine failure and damage to the airplane.
2020-19-11: The FAA is adopting a new airworthiness directive (AD) for certain Leonardo S.p.a. (Leonardo) Model A119 and AW119 MKII helicopters. This AD requires repetitive borescope inspections of the tail rotor gearbox (TGB) and depending on the inspection results, removing the TGB from service. \n\n((Page 59405)) \n\nThis AD was prompted by reports of corrosion on the internal surface of the 90-degree TGB output shaft. The actions of this AD are intended to address an unsafe condition on these products.
95-17-03: This amendment supersedes an existing airworthiness directive (AD), applicable to all Lockheed Model L-1011 series airplanes, that currently requires a visual inspection to detect cracks of the forward or aft side of the aft pressure bulkhead, and repair, if necessary. This amendment requires various inspections to detect cracks or other discrepancies of the aft pressure bulkhead, and repair, if necessary. This amendment is prompted by a recent report of in-flight loss of cabin pressure on a Model L-1011-385 series airplane due to a rupture of the aft pressure bulkhead as a result of fatigue-related cracking. The actions specified in this AD are intended to prevent such fatigue cracking, which could result in rupture of the aft pressure bulkhead and subsequent depressurization of the cabin.
2008-12-04: We are adopting a new airworthiness directive (AD) for certain Boeing Model 737-600, -700, -700C, -800, and -900 series airplanes. This AD requires various repetitive inspections to detect cracks along the chemically milled steps of the fuselage skin or missing or loose fasteners in the area of the preventative modification or repairs, replacement of the time-limited repair with the permanent repair if applicable, and applicable corrective actions if necessary, which would end certain repetitive inspections. This AD results from a fatigue test that revealed numerous cracks in the upper skin panel at the chemically milled step above the lap joint. We are issuing this AD to detect and correct such fatigue-related cracks, which could result in the crack tips continuing to turn and grow to the point where the skin bay flaps open, causing decompression of the airplane.
2001-13-51: This document publishes in the Federal Register an amendment adopting Airworthiness Directive (AD) 2001-13-51, which was sent previously to all known U.S. owners and operators of Bell Helicopter Textron Canada (BHTC) Model 206L-4, 407, and 427 helicopters by individual letters. This AD requires visually inspecting certain driveshafts for a crack, a loose bolt or nut, or red powder residue. If a crack, a loose bolt or nut, or red powder residue is found, replacing the driveshaft before further flight and notifying the FAA within 10 days is also required. This amendment is prompted by a driveshaft failure on a BHTC Model 407 helicopter that resulted in an engine shutdown and an emergency landing. Failure of the driveshaft was due to cracking of the flexframe on the forward end of the driveshaft. In addition, three other incidents of a cracked flexframe on the forward end of the driveshaft on other Model 407 helicopters have been reported. The actions specified by this AD are intended to prevent failure of a driveshaft, loss of drive to the main rotor system, and a subsequent emergency forced landing.
2020-19-07: The FAA is adopting a new airworthiness directive (AD) for Leonardo S.p.a. Model AW169 helicopters. This AD requires modifying the weight on wheels (WoW) support installation on the main landing gear (MLG). This AD was prompted by a report that an inappropriately tightened WoW support could result in a rotation of the support and improper WoW switch performance. The actions of this AD are intended to address an unsafe condition on these products.