Results
64-02-03: 64-02-03 CALLAIR: Amdt. 672 Part 507 Federal Register January 17, 1964. Applies to All Models A-5 and A-6 Aircraft. Compliance required as indicated. As a result of several failures of the front attaching tube of the horizontal stabilizer, accomplish the following: (a) Within 25 hours' time in service after the effective date of this AD check for cracks as follows: (1) Remove the horizontal stabilizers from the airplane and thoroughly clean the leading edge tube of the horizontal stabilizer by removing all paint, rust, and foreign materials. Check for cracks in the area where the tube attaches to the fuselage carry through member and also around the horizontal tail fixed handle area where the tube has been bent back to provide sweepback. (2) Inspect for cracks using the magnetic particle inspection process. (b) If cracks are found, either install a new stabilizer or make an FAA approved repair. Thereafter reinspect the stabilizer at intervals not to exceed 100 hours' time in service. (c) If no cracks are found, reinstall stabilizers and reinspect at intervals not to exceed 100 hours' time in service. (d) CallAir Service Kit No. 10 provides a suitable reinforcement of the empennage by the installation of additional brace wires to the forward portion of the tail surfaces. No further periodic inspections are required if CallAir Service Kit No. 10 is installed with a new or repaired horizontal stabilizer. (CallAir Service Bulletin No. 10 covers this same subject.) This directive effective January 17, 1964.
2005-13-28: This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 777-200 and -300 series airplanes. This AD requires a one-time inspection of the clevis end of the vertical tie rods that support the center stowage bins to measure the exposed thread, installation of placards that advise of weight limits for certain electrical racks, a one-time inspection and records check to determine the amount of weight currently installed in those electrical racks, corrective actions, and replacement of the vertical tie rods for the center stowage bins or electrical racks with new improved tie rods, as applicable. The actions specified by this AD are intended to prevent failure of the vertical tie rods supporting certain electrical racks and the center stowage bins, which could cause the center stowage bins or electrical racks to fall onto passenger seats below during an emergency landing, impeding an emergency evacuation or injuring passengers. This action is intended to address the identified unsafe condition.
2018-10-04: We are superseding Airworthiness Directive (AD) 2018-03-15 for Pacific Aerospace Limited Model 750XL airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as reports of finding abrasion damage behind the instrument panel caused by ventilation hose chafing. We are issuing this AD to require actions to address the unsafe condition on these products.
85-05-51 R2: 85-05-51 R2 BRITISH AEROSPACE: Amendment 39-5077. Applies to Model BAe 146 airplanes certificated in all categories on which Modification HCM00650A has not been accomplished. Compliance is required before further flight after the effective date of this airworthiness directive (AD). To prevent fuel leaks into the passenger cabin and prevent potential fire, accomplish the following unless previously accomplished: A. Before further flight: 1. Drain center fuel tank, and 2. Incorporate the following information into the airplane flight manual and provide to flight crews: DO NOT DISPATCH WITH FUEL IN THE CENTER TANK. B. Within 48 hours after the effective date of this AD, modify the airplane in accordance with BAe 146 Alert Service Bulletin 28-A3 Revision 2, dated March 25, 1985, paragraph 2A. C. Incorporation of British Aerospace Modification HCM00650A terminates the requirement to comply with paragraphs A. and B., above, of this directive. D. Alternate means of compliance which provide an acceptable level of safety may be used when approved by the Manager, Seattle Aircraft Certification Office, FAA, Northwest Mountain Region. NOTE: Compliance with paragraph A.2. of this directive may be effected by including a copy of the AD in the airplane flight manual and operating manual. All persons affected by this proposal who have not already received these documents from the manufacturer may obtain copies upon request to British Aerospace, Librarian for Service Bulletins, Box 17414, Dulles International Airport, Washington, D.C. 20041. These documents also may be examined at the FAA, Northwest Mountain Region, 17900 Pacific Highway South, Seattle, Washington, or 9010 East Marginal Way South, Seattle, Washington. This Amendment 39-5077 becomes effective June 24, 1985. It was effective earlier to all recipients of telegraphic AD T85-05-51 issued March 15, 1985, and T85-05-51 R1, issued March 22, 1985, which containedthis amendment.
63-22-03: 63-22-03 MARVEL-SCHEBLER: Amdt. 636 Part 507 Federal Register October 30, 1963. Applies to All MA4-5 Carburetors Not Having the One-Piece Combination Primary and Main Venturi and Used on the Following: Continental O-470 Series Engines Installed in Cessna 180 and 182 Series Aircraft; Continental GO-300 Series Engines Installed in Cessna 175 and P172 Series Aircraft; Lycoming O-540 Series Engines Installed in Aero Commander 500 Series Aircraft, Piper PA-23-250 Series Aircraft and Piper PA-24 Series Aircraft; Lycoming O-360 Series Engines Installed in Piper PA-24 Series Aircraft, Beech 95 Series Aircraft, and Mooney Mark 20 or 21 Series Aircraft; and Franklin 6A4-165 Series Engines Installed in Stinson 108 Series Aircraft. Compliance required at next carburetor removal or overhaul of either the carburetor or engine whichever occurs first after the effective date of this AD, on all carburetors not having the one-piece combination primary and main venturi installed. Carburetorshaving the one-piece combination primary and main venturi installed are identified by the letter "V" stamped on the nameplate. The primary venturi may become loose resulting in wear of the primary venturi support legs on the ends contacting the carburetor body and at the retaining clip area. As a result, the retaining clips may become dislodged or dislocated and wear may progress to the point the venturi becomes dislodged or dislocated. This can cause erratic engine operation or complete engine stoppage. To preclude this, accomplish the following: Replace the existing primary and main venturi with a one-piece combination primary and main venturi of the correct part number for the carburetor involved. When accomplished stamp the letter "V" on the carburetor nameplate below the serial number. (Marvel-Schebler Service Bulletin No. A4-63, Lycoming Service Bulletin No. 297, and Continental Motor Service Bulletin No. M63-18 cover this same subject.) This directive effective December 2, 1963.
63-20-01: 63-20-01 BELLANCA: Amdt. 620 Part 507 Federal Register September 19, 1963. Applies to All Model 14-13 Series Aircraft. Compliance required as indicated. Within 50 hours' time in service after the effective date of this AD, and at intervals thereafter not to exceed 50 hours' time in service from the last inspection, accomplish the following: (a) Inspect for cracks in the welds and the structure immediately adjacent to the area where the left and right brake-cylinder support brackets, P/N's 9811-17 and -21, are attached to the fuselage cross tube P/N 9802-47 (located directly aft of the firewall, below the cabin floor), using a dye penetrant and a 10-power glass or an FAA approved equivalent. Prior to inspection, all grease and dirt shall be removed from the surfaces involved. (b) If cracks are found, that part must be repaired in accordance with an FAA approved repair, or replaced by a part of the same part number, or an FAA approved equivalent part before further flight. This directive effective October 21, 1963.
2018-09-12: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-200B, 747-300, and 747-400 series airplanes. This AD requires replacing certain low-pressure oxygen flex- hoses with new non-conductive low-pressure oxygen flex-hoses in the gaseous passenger oxygen system in airplanes equipped with therapeutic oxygen. This AD also requires a general visual inspection of the low- pressure passenger oxygen system to ensure there is minimum clearance of the oxygen system components from adjacent structure and systems. This AD was prompted by reports of low-pressure flex-hoses of the flightcrew oxygen system that burned through due to inadvertent electrical current from a short circuit. We are issuing this AD to address the unsafe condition on these products.
2005-15-03: The FAA is adopting a new airworthiness directive (AD) for certain McDonnell Douglas airplanes identified above. This AD requires repetitive functional tests for noisy or improper operation of the exterior emergency control handle assemblies of the mid, overwing, and aft passenger doors, and corrective actions if necessary. This AD also provides for optional terminating action for the repetitive tests. This AD is prompted by a report that the exterior emergency control mechanism handles were inoperative on a McDonnell Douglas Model MD-11 airplane. We are issuing this AD to prevent failure of the passenger doors to operate properly in an emergency condition, which could delay an emergency evacuation and possibly result in injury to passengers and flightcrew.
86-20-13: 86-20-13 ALLISON GAS TURBINE DIVISION, GENERAL MOTORS CORP. (ALLISON, formerly DETROIT DIESEL ALLISON): Amendment 39-5465. Applies to Allison Model 250-C28 and -C30 Series engines installed in, but not limited to, Bell Model 206L-1, Messerschmitt-Bolkow-Blohm GmbH BO 105 LS A- 1, Sikorsky Model S-76A, Bell Model 206L-1, modified to incorporate the Allison 250-C30 engine, Bell Model 206L-3, and McDonnell Douglas Helicopter Company (Hughes) Model 369F and 369FF aircraft. The following engine models and turbine serial numbers are affected: ENGINE MODEL TURBINE SERIAL NUMBER 250-C28B CAT 70001 thru 70802 and 70804 250-C28C CAT 28001 thru 28046 250-C30 Series CAT 90001 thru 95436 and 95438 EXCEPT existing Model 250-C28 and 250-C30 Series engines which have incorporated Allison Commercial Engine Alert Bulletin 250-C28/C30 CEB-A-72-2132/3146 dated October 1, 1985, or the following FAA approved equivalents: Allison Message THO-2639W-RFR-85 dated February 7, 1985Allison C28 Overhaul Manual Temporary Revision 72-7, Page 12 dated January 22, 1986 Allison C30 Overhaul Manual Revision dated July 1, 1985, Section 72-50-00, Paragraph (7), page 524 Allison Commercial Service Letter 250-C28/C30 CSL-2071/3073 dated June 1, 1985 Compliance is required as indicated unless already accomplished. To prevent excessive wear and/or fretting damage on the external splines of the turbine spline adapter or the aft splines of the turbine-to-compressor coupling shaft, which can progress to a disconnect and subsequent overspeed gas generator turbine failure/uncontained failure, accomplish the following: (a) Within the next five hours time-in-service after the effective date of this AD, but not later than December 20, 1986, for inservice engines, inspect the gas generator turbine spline adapter locknut torque in accordance with Allison Commercial Engine Alert Bulletin 250-C28/C30 CEB-A-72-2132/3146 dated October 1, 1985, or FAA approved equivalent.(b) Before initial flight, for uninstalled affected turbine assemblies, inspect the gas generator turbine spline adapter locknut torque in accordance with Allison Commercial Engine Alert Bulletin 250-C28/C30 CEB- A-72-2132/3146 dated October 1, 1985, or FAA approved equivalent. NOTE: The compliance requirements of this AD were previously published in Allison Commercial Service Letter 250-C28/C30 CSL-A-2084/3087, Revision 1, dated September 29, 1986, FAA approved by the Manager, Chicago Aircraft Certification Office. Aircraft may be ferried in accordance with the provisions of FAR 21.197 and 21.199 to a base where the AD can be accomplished. Upon request, an equivalent means of compliance with the requirements of this AD may be approved by the Manager, Chicago Aircraft Certification Office, FAA, 2300 East Devon Avenue, Des Plaines, Illinois 60018. Allison Commercial Engine Alert Bulletin 250-C28/C30 CEB-A-72-2132/3146 dated October 1, 1985, is incorporated herein and made a part hereof pursuant to 5 U.S.C. 552 (a)(1). All persons affected by this directive who have not already received this document from the manufacturer may obtain copies upon request to Allison Gas Turbine Division, General Motors Corp., P.O. Box 420, Indianapolis, Indiana 46206-0420. This document also may be examined at the Office of Regional Counsel, FAA, ATTN: Rules Docket No. 86-ANE-41, 12 New England Executive Park, Burlington, Massachusetts 01803, weekdays, except Federal holidays, between 8:00 a.m. and 4:30 p.m. This amendment becomes effective December 3, 1986, as to all persons except those persons to whom it was made immediately effective by Priority Letter AD No. 86-20-13, issued October 8, 1986, which contained this amendment.
2005-10-24: The FAA adopts a new airworthiness directive (AD) to supersede AD 2003-14-20, which applies to all AeroSpace Technologies of Australia Pty Ltd. (ASTA) Models N22B and N24A airplanes. AD 2003-14-20 requires you to repetitively inspect, using either dye penetrant or magnetic particle methods, the rudder control lever shafts for cracks; inspect (one-time) all lever shaft side plates by measuring the thickness; and if cracks or discrepancies in thickness are found, replace unserviceable parts with new or serviceable parts. Since AD 2003-14-20 was issued, we determined that the AD should also affect Model N22S airplanes. The manufacturer has also revised the service information to include a rudder control lever shaft part number (P/N) that was not part of AD 2003-14-20. Consequently, this AD retains the actions of AD 2003-14-20, adds Model N22S airplanes to the applicability, and adds rudder control lever shaft P/N 1/N-45-1102 to the inspection requirements. We are issuing this ADto detect and correct cracks in the rudder control lever torque shafts and discrepancies in the thickness of the lever shaft side plates, which could result in failure of the rudder control lever torque shaft. Such failure could lead to reduced controllability of the airplane.