Results
81-23-07: 81-23-07 PIPER: Amendment 39-4252. Applies to Model PA-38-112 Serial Nos. 38-78A0001 thru 38-78A0678 certificated in all categories except aircraft incorporating engine mount assembly Piper Part Number 77651-02. To prevent possible nose-gear failure associated with weakening of the engine-mount, accomplish the following unless previously accomplished: a. On aircraft modified in accordance with Piper S/B 617 dated October 12, 1978, or equivalent, with less than 950 hours in service since incorporation of the modification, inspect and replace, if required, the engine mount within the next 50 hours in service after the effective date of this AD, in accordance with Piper S/B 617B dated January 13, 1981, Instructions Paragraph 3 or equivalent. Repeat inspection at intervals not to exceed 50 hours until 1000 hours in service from modification or until replacement of the engine mount with engine mount assembly Piper Part Number 77651-02. Replacement engine mount P/N 77651-02must be installed prior to the accumulation of 1000 hours in service on modified engine mount. b. On aircraft modified in accordance with Piper S/B 617 dated October 12, 1978, or equivalent, with 950 or more hours in service since the modification, within the next 50 hours in service after the effective date of this AD, replace the engine mount with engine mount assembly Piper Part No. 77651-02. c. On aircraft which have not been modified in accordance with Piper S/B 617, dated October 12, 1978, within the next 50 hours in service after the effective date of this AD, replace the engine mount with engine mount assembly Piper Part No. 77651-02. d. Alternative inspections and alterations which provide an equivalent level of safety may be used when approved by the Chief, Engineering and Manufacturing Branch, FAA, Eastern Region. e. Upon submission of substantiating data through an FAA Maintenance Inspector, the compliance times specified in this AD may be adjusted by the Chief, Engineering and Manufacturing Branch, FAA, Eastern Region. This amendment supersedes AD 79-01-07. This amendment is effective November 16, 1981.
2002-09-12: This amendment adopts a new airworthiness directive (AD) that applies to certain Raytheon Aircraft Company (Raytheon) Beech Model C90 airplanes. This AD requires you to inspect the left-hand (LH) and right-hand (RH) nacelle and spar assembly for the existence of rivets, and requires you to install rivets if they do not exist or are the wrong size or type. This AD is the result of Raytheon identifying several instances where rivets were either missing or were the wrong size or type on these airplanes. The actions specified by this AD are intended to correct the installation of rivets in the LH and RH nacelle and spar assembly. These rivets must be present and have the correct dimension in order to prevent reduced structural integrity, which could result in structural failure and possible loss of control of the airplane.
2023-12-12: The FAA is superseding Airworthiness Directive (AD) 2022-04- 05, which applied to all The Boeing Company Model 757 and 767 airplanes. AD 2022-04-05 required revising the limitations and operating procedures sections of the existing airplane flight manual (AFM) to incorporate specific operating procedures for landing distance calculations, instrument landing system (ILS) approaches, non-precision approaches, speedbrake deployment, and go-around and missed approaches, when in the presence of interference from wireless broadband operations in the 3.7-3.98 GHz frequency band (5G C-Band) as identified by Notices to Air Missions (NOTAMs). Since the FAA issued AD 2022-04-05, the FAA determined that additional limitations are needed due to the continued deployment of new 5G C-Band base stations whose signals are expected to cover most of the contiguous United States at transmission frequencies between 3.7-3.98 GHz. This AD requires revising the limitations and operating procedures sections of the existing AFM to incorporate specific operating procedures for landing distance calculations, ILS approaches, non-precision approaches, speedbrake deployment, and go- around and missed approaches, due to the presence of 5G C-Band interference. The FAA is issuing this AD to address the unsafe condition on these products.
80-25-07 R1: 80-25-07 R1 STEWART-WARNER CORPORATION: Amendment 39-4028 as amended by Amendment 39-4220. Applies to the following Stewart-Warner oil cooler models: \n\n\nSTEWART WARNER\nMODEL NOS.\nBEGINNING\nSERIAL NOS.\nENDING \nSERIAL NOS. \n8406J\n12558\n16212 \n8406L\n1496\n1763 \n8432K\n514\n541 \n8432L\n631\n964 \n10568C\n1105\n1141 \n10578B\n2212\n2316 \n10599A\n7369\n9013 \n10610A\n1815\n1956 \n10614A\n732\n947 \n10622A\n333\n394 \n10634D\n105\n907 \n8446C\n372\n629 \n8437C\n422\n472 \n10641B\n101\n162 \n8493B\n1269\n1603\n\n\tNOTE: The affected oil coolers were manufactured between July 1, 1979, and November 1, 1980. Oil coolers of the above model and serial numbers that have a date ink stamped next to the nameplate have been inspected by Stewart-Warner and found satisfactory for continued use. \n\n\tThese oil coolers may be installed on, but not limited to, the following aircraft: \n\n\tBellanca Models: 7ECA, 7GCAA, 7GCBC, 7KCAB, 8GCBC, and 8KCAB. \n\n\tCessna Models (including Reims Aviation): 152, A152, F152, FA152, 172I, 172K, 172L, 172M, 172N, 172P, 172RG, F172L, F172M, F172P, 177, 177A, 177B, 177RG, F177RG, R182, FR182, TR182, T182, A188B, T188C, 210N, T210N, and P210N. \n\n\tPiper Model: PA-38-112. \n\n\tMooney Models: M20C, M20E, M20F, M20G, and M20J. \n\n\tGreat Lakes Models: 2T-1A-1 and 2T-1A-2. \n\n\tBeech Models: 269 Series. \n\n\tCompliance is required prior to further flight after the effective date of this AD, unless already accomplished. To prevent the loss of engine oil, accomplish the following: \n\n\t1.\tIf the oil cooler has accumulated 10 hours or less total time in service since new, prior to further flight, replace with an airworthy oil cooler not of the above serial numbers or with an airworthy oil cooler of the above serial numbers that have a date ink stamped next to the oil cooler name plate. \n\n\t\tNOTE: Removed oil coolers may be returned to: Stewart-Warner Corp., Attn: Mr. Ben Gillen, 1514 Drover Street, Indianapolis, Indiana 46221. \n\n\t2.\tIf the oil cooler has accumulated more than 10 hours time in service since new, visually inspect the cooler for oil leakage prior to further flight. \n\n\t\tNOTE: Removal of the engine cowling is not required if it can be positively determined from inspection of areas adjacent to the oil cooler that the oil cooler is not leaking. \n\n\t\tA.\tIf oil leakage is evident, prior to further flight, replace with an airworthy oil cooler not of the above serial numbers or with an airworthy oil cooler of the above serial numbers that have a date ink stamped next to the oil cooler name plate. \n\n\t\tB.\tIf oil leakage is not detected: \n\n\t\t\ti.\tFabricate and install the following placard on the aircraft instrument panel in plain view of the crew, using letters 1/8-inch high minimum: \n\n\t\t\t"Visually check oil cooler for leakage prior to each flight. If leakage is detected, refer to AD Number 80-25-07." \n\n\t\tNOTE: The owner or operator may make and install this placard and conduct the preflight check.This check does not require a logbook entry. The inspection procedures identified in the note following paragraph 2 also apply to this preflight check. \n\n\t\t\tii.\tIf the oil cooler is replaced with an airworthy oil cooler not of the above serial numbers or with an airworthy oil cooler of the above serial numbers that have a date ink stamped next to the oil cooler name plate, the placard can be removed. \n\n\t3.\tAny equivalent method of compliance with this AD must be approved by the Chief, Engineering and Manufacturing Branch, FAA, 2300 East Devon Avenue, Des Plaines, Illinois 60018, telephone (312) 694-7357. \n\n\tAmendment 39-4028 became effective January 29, 1981, as to all persons except those to whom it was made immediately effective by the priority mail letter dated December 5, 1980, which contained this amendment. \n\n\tThis amendment 39-4220 becomes effective September 24, 1981.
2002-09-10: This amendment adopts a new airworthiness directive (AD), that is applicable to CFE Company Model CFE738-1-1B turbofan engines. This amendment requires replacing the high pressure turbine (HPT) stage 1 aft cooling plate and HPT stage 2 disk at or before they reach new reduced life cycle limits. This amendment is prompted by analysis of the existing life cycle limits by the engine manufacturer. The actions specified by this AD are intended to prevent failure of the HPT stage 1 aft cooling plate and HPT stage 2 disk, which could result in an uncontained engine failure and damage to the airplane.
81-16-10: 81-16-10 PIPER AIRCRAFT CORPORATION: Amendment 39-4210. Applies to the following Piper models of aircraft certificated in all categories: PA-44-180 Seminole, S/N 44- 7995001 through 44-8195016; PA-44-180T Turbo Seminole, S/N 44-8107001 through 44- 8107044. Compliance is required as indicated upon receipt of this directive, unless already accomplished. NOTE: An airmail letter was mailed to owners and operators on August 3. To prevent possible damage to the outboard leading edge skin, as well as an aileron out- of-balance condition which could lead to aeroelastic instability, accomplish the following: (a) Before further flight, visually check for cracks at the aileron outboard leading edge balance weight attachment screws. (1) If cracks are found, comply with paragraph (d). (2) If no cracks are found, make log book entry that visual check was made. NOTE: The visual check only may be accomplished by the pilot. (b) At intervals not to exceed25 hours until 100 hours time in service from the effective date of this AD accomplish the following: (1) Inspect, using a 10-power magnifying glass, the left and right aileron outboard leading edge skin for cracks near the balance weight attachment screws. (2) If the skin is cracked near any balance weight attachment screw, comply with paragraph (d) of this AD before further flight. (3) If there are no cracks, make appropriate log book entry of each inspection. (c) Within 100 hours time in service from the effective date of this AD comply with paragraph (d). (d) Reinforce the ailerons outboard leading edge skins by installing Piper's aileron rework kit, Piper Part No. 764 148V in accordance with instructions included with the kit, and make appropriate log book entry. An equivalent method of compliance may be approved by the Chief, Engineering and Manufacturing Branch, Federal Aviation Administration, Southern Region. Airplanes on which cracks arefound may be flown in accordance with FAR 21.197 and 21.199 to a base where the aileron rework kit can be installed, provided the airplane is not flown in excess of 130 MPH indicated speed. Piper Service Bulletin No. 725A pertains to this subject. This amendment becomes effective September 17, 1981, and was effective upon receipt of the airmail letter mailed August 3 to owners and operators.
2023-11-04: The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-100-1A10 airplanes. This AD was prompted by a report that a design deficiency was discovered which could allow a no-back pawl to be incorrectly installed in a horizontal stabilizer trim actuator (HSTA). This AD requires a check for part number and serial numbers of the HSTA, and if necessary, inspection of the no-back pawl installation, and corrective action. The FAA is issuing this AD to address the unsafe condition on these products.
2002-09-07: This amendment adopts a new airworthiness directive (AD), applicable to certain McDonnell Douglas Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), and MD-88 airplanes. This AD requires an inspection of the electrical power feeder cables in the aft cargo compartment sidewall for chafing and/or preloading, and corrective actions, if necessary. This action is necessary to prevent possible arcing of the electrical power cables in the aft cargo compartment sidewall and consequent damage to equipment and the adjacent structure, which could result in smoke and/or fire in the cargo compartment. This action is intended to address the identified unsafe condition.
2002-08-17: This amendment adopts a new airworthiness directive (AD) that is applicable to certain McDonnell Douglas Model DC-10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10-30F, and DC-10-30F (KC10A and KDC-10) airplanes. This action requires revising the airplane flight manual to advise the flightcrew of necessary procedures if certain thrust reverser indicator lights illuminate or are inoperative, and locking out any affected thrust reverser under certain conditions. This action also provides for returning a thrust reverser to service after it has been locked out. This action is necessary to prevent an uncommanded in-flight deployment of a thrust reverser, which could result in reduced controllability of the airplane. This action is intended to address the identified unsafe condition.
2002-09-01: This amendment adopts a new airworthiness directive (AD), that is applicable to Pratt & Whitney (PW) PW4090, PW4090-3, PW4074D, PW4077D, PW4090D, and PW4098 turbofan engines with 15th stage high pressure compressor (HPC) disks having certain part numbers (P/N's). This amendment requires initial and repetitive borescope inspections of 15th stage HPC disks for cracks in the knife edges, eddy current inspections (ECI's) of blade loading slots if required, and removal of cracked disks. In addition, this amendment requires the removal from service of these P/N disks, at a new lower cyclic life limit. This amendment is prompted by two reports of 15th stage HPC disks with cracks in the outer rim front rail of the blade loading slots, and in the front forward and middle knife edges. The actions specified by this AD are intended to prevent 15th stage HPC disk failures from cracks, which could result in an uncontained engine failure.