Results
2001-23-12: This amendment adopts a new airworthiness directive (AD), applicable to certain Saab Model SAAB SF340A and SAAB 340B series airplanes, that requires a one-time review of records to determine whether an airplane has been repainted since its delivery from the factory; and a one-time inspection to detect damage associated with improper preparation for the repainting, and corrective action if necessary. This amendment is prompted by mandatory continuing airworthiness information from a foreign civil airworthiness authority. The actions specified by this AD are intended to detect and correct damage to the aluminum skin of the airplane, which could result in a weakening of the structure of the airplane.
2016-05-11: We are adopting a new airworthiness directive (AD) for Sikorsky Aircraft Corporation (Sikorsky) Model S-92A helicopters. This AD requires certain inspections of the main rotor and tail rotor control pushrods (pushrods). This AD is prompted by a Sikorsky investigation that indicated that some pushrods may have incorrectly installed locking mechanisms. These AD actions are intended to detect an incorrectly installed locking mechanism, which if not corrected, could result in a loose jam nut, failure of the pushrod, loss of main rotor or tail rotor flight control, and consequent loss of helicopter control.
2015-12-12: We are adopting a new airworthiness directive (AD) for all Fokker Services B.V. Model F.28 Mark 0070 and 0100 airplanes. This AD was prompted by a report of two cases of heavy (hard to move) aileron control caused by aileron cables stuck in a clump of ice in the wheel bay. This AD requires installing drain tubes on the center wing rear spar. We are issuing this AD to prevent accumulated water near or on the aileron control cables, which could freeze and result in reduced control of the airplane.
2005-12-13: The FAA is adopting a new airworthiness directive (AD) to supersede AD 2005-05-52 (70 FR 13362, March 21, 2005), which applies to all Cessna Aircraft Company (Cessna) Models 402C and 414A airplanes. AD 2005-05-52 currently requires you to eddy current inspect the forward wing spars and visually inspect the aft and auxiliary spars. This AD is the result of fatigue and crack growth analyses of the wings of these airplanes, recent cracks found on Model 402C airplanes, and the FAA's determination that repetitive inspections and a wing spar modification are necessary to address the unsafe condition. Consequently, this AD would require repetitive eddy current inspections, visual inspections, and a spar strap modification on each wing. You must retain the actions of AD 2005-05-52 until you do the modifications of this AD. The actions specified by this AD are intended to prevent wing spar cap failure caused by undetected fatigue cracks. Such failure could result in loss of a wing withconsequent loss of airplane control. FAA is also issuing AD 2005-12-12 to require the spar strap modification and long-term inspections on Models 401, 401A, 402, 402A, 402B, 411, and 411A airplanes.
53-15-03: 53-15-03 HARTZELL: Applies to All Model HC-82XF-1 Controllable Pitch Propellers Installed on Cessna 180 Aircraft. Compliance required as indicated. A number of recent in service failures of the pitch change link screws (P/N A-98) on Hartzell HC-32XF-1 propellers have resulted in exposing the occupants to hazardous situations. All such propeller failures have resulted in forced landings, some of which caused major damage to the aircraft. Due to the serious nature of these failures, the following inspections and replacements are necessary: I. Inspection. A. Prior to August 1, 1953, visually inspect all link screws to determine: (1) If any are broken. (2) If any are cracked or bent. (3) If any are not fully seated on the conical seat. B. If any are found broken, cracked, bent or not fully seated on the conical seat, prior to further flight replace with screws as noted in item II. C. If visual inspection proves satisfactory, the propellermay be flown subject to compliance with item II. II. Replacement. Compliance required prior to September 1, 1953. A. Replace all original A-98 link screws with improved A-98-B link screws in accordance with Hartzell Service Bulletin No. 24, dated May 28, 1953. B. Propeller with serial numbers not listed in Service Bulletin No. 24 may not have the improved screws. Owners of these propellers shall check with the propeller manufacturer for verification.
64-02-01: 64-02-01 AERO COMMANDER: Amdt. 676 Part 507 Federal Register January 21, 1964. Applies to Models 500A, 500B, 560F, 680F (Pressurized) and 680FL Aircraft Serial Numbers 871, 875, and 893 through 1329 Except Serial Numbers 916, 953, 1162, 1186, 1207, 1224, 1234, 1293, 1303, 1325, 1327, and 1328. Compliance required as indicated. To detect loosened set screws and to preclude rotation of the upper retaining bearing on the main landing gear accomplish the following: (a) Within 25 hours' time in service after the effective date of this AD, inspect the main landing gear in accordance with Part I of Aero Commander Service Bulletin No. 83 dated September 13, 1963, or FAA approved equivalent. If the extension of either gear exceeds 9.125 plus or minus 0.125 inches, accomplish the modification specified in (b) for both main landing gears before further flight. (b) Within 50 hours' time in service after the effective date of this AD, modify the landing gear in accordancewith Part II of Aero Commander Service Bulletin No. 83 dated September 13, 1963, or FAA approved equivalent. Stamp the letter "A" after the design number on each landing gear data plate after the modification is made. This directive effective February 20, 1964.
63-27-03: 63-27-03 PIPER: Amdt. 661 Part 507 Federal Register December 24, 1963. Applies to All Models PA-24 and PA-24-250 Aircraft, Which Have 25 Ampere Circuit Breakers in the Landing Gear Retraction Motor Circuit. Compliance required within the next 100 hours' time in service after the effective date of this AD. Inadvertent tripping of the 25 ampere landing gear retraction circuit breaker has resulted in stoppage of the landing gear retraction mechanism in other than the fully extended position. Therefore, in order to eliminate this condition, with its associated hazard of partial-gear-down landing accidents, the 25 ampere circuit breaker in the landing gear retraction motor circuit must be replaced with a 30 ampere circuit breaker, Piper P/N 454661, or FAA approved equivalent. (Piper Service Letter No. 356, dated March 31, 1961, pertains to this same subject.) This directive effective January 23, 1964.
2001-15-04: This amendment supersedes an existing airworthiness directive (AD), applicable to all Dornier Model 328-100 series airplanes, that currently requires repetitive inspections of the left and right roll spoiler actuators to check for signs of leakage and deformation of the housing, repetitive inspections of the gap between the left roll spoiler actuator housing cap and the actuator housing, repetitive torque checks of the left roll spoiler actuator housing cap attachment screws, and corrective action, if necessary. This amendment requires replacement of the double shuttle valves in the roll spoiler actuators with new improved valves, which constitutes terminating action for the requirements of this AD. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by this AD are intended to prevent oil leakage from the roll spoiler actuators, which could result in incorrect roll spoiler operation and reduced controllability of the airplane.
2015-11-09: We are adopting a new airworthiness directive (AD) for Sikorsky Aircraft Corporation (type certificate previously held by Schweizer Aircraft Corporation) (Sikorsky) Model 269D and Model 269D Configuration A helicopters. This AD requires reducing the life limit of the ring gear carrier assembly. This AD was prompted by cracks in the ring gear carrier assembly. The actions are intended to reduce the life of the ring gear carrier assembly to prevent failure of the main rotor transmission, loss of engine power to the main rotor, and subsequent loss of control of the helicopter.
63-24-03: 63-24-03 PIPER: Amdt. 649 Part 507 Federal Register November 27, 1963. Applies to All Models PA-23 and PA-23-160 Aircraft. Compliance required within the next 50 hours' time in service after the effective date of this AD, unless already accomplished within the past 50 hours' time in service. Every 100 hours' time in service thereafter comply with paragraphs (b), (c), and (d). Several failures of the rudder trim tab actuating rod, Piper P/N 17271-00, through the bend radius of the forward hooked end and a disconnection due to a lost cotter pin have resulted in free trim tabs oscillating the rudder. Therefore, the following must be accomplished: (a) Remove the rudder trim tab control rod assembly from the aircraft. (b) Visually inspect for cracks in the area of the hooked end using a magnifying lens of at least 10-power. (c) Check the hooked end for wear in excess of 0.040 inch in the area of contact with the jackscrew. (d) Rudder trim tab control rods with cracks, or wear in excess of 0.040 inch shall be replaced before further flight. (e) Redrill the cotter pin hole in the hooked end to 0.081 inch-diameter and reinstall the rudder trim tab control rod assembly using a roll pin, Piper P/N 480728, and 0.032 inch- diameter steel safety wire, in lieu of the cotter pin. (Piper Service Letter No. 407, dated October 4, 1963, which pertains to this same subject, outlines and illustrates inspection and installation methods.) This directive effective November 27, 1963.