Aircraft-logs.com

Results
81-02-02: 81-02-02 GENERAL ELECTRIC COMPANY: Amendment 39-4004. Applies to all General Electric CT58 turboshaft engines incorporating stage one turbine wheel, part number 4002T17P02, with the following wheel serial numbers: 7753, 7761, 7762, 7767, 7768, 7783, 7799, 7803, 7811, 7815, 7817, 7819, 7820, 7823, 7824, 7828, 7839, 7845, and 7846. Compliance required as indicated, unless already accomplished. To prevent failure of stage one turbine wheels due to cracks originating from undersize rabbet groove radii, inspect forward and aft radii in accordance with the procedures contained in the accomplishment instruction section of General Electric Alert Service Bulletin CT58 (A72-159) CEB-255, dated July 9, 1979, or later FAA approved revision, or equivalent means approved by the Chief, Engineering and Manufacturing Branch, New England Region. Inspect in accordance with the following schedule: 1. Turbine wheels with 3.950 hours or 7,900 cycles, or more, in service on the effective date of this AD, must be inspected within the next 50 hours or 100 cycles, whichever comes first. 2. Turbine wheels with less than 3,950 hours or 7,900 cycles in service, on the effective date of this AD, must be inspected prior to exceeding 4,000 hours or 8,000 cycles, whichever comes first. Stage one turbine wheels with forward or aft rabbet groove radii of less than 0.010 inch must be removed and replaced with serviceable turbine wheels prior to further flight. The manufacturer's specifications and procedures identified and described in this directive are incorporated herein and made a part hereof pursuant to 5 U.S.C. 552(a)(1). All persons affected by this directive who have not already received these documents from the manufacturer may obtain copies upon request to General Electric Company, 1000 Western Avenue, Lynn, Massachusetts 01910. These documents may also be examined at Federal Aviation Administration, New England Region, 12 New England Executive Park, Burlington, Massachusetts 01803, and at FAA Headquarters, 800 Independence Avenue, S.W., Washington, D.C. A historical file on this AD, which includes the incorporated material in full, is maintained by the FAA at its Headquarters in Washington, D.C., and at FAA, New England Region Headquarters, Burlington, Massachusetts. This amendment becomes effective February 2, 1981.
47-22-03: 47-22-03 PIPER: (Was Mandatory Note 4 of AD-780-3.) Applies Only to PA-12 Aircraft Serial Numbers 12-1 and Up to 12-249 Except Serial Numbers 12-221, 12-236, 12-239 and 12-244. Compliance required prior to August 1, 1947. Reinforce the upper end of the tie strap on the landing gear with a 0.125 x 1 1/2 x 4 1/2, 4130 steel plate. Bend and trim to fit and install over end of strap by edge welding. (Piper Service Bulletin No. 93 dated August 8, 1946, covers this same subject.)
84-20-51: 84-20-51 GARRETT TURBINE ENGINE COMPANY (GTEC) (formerly AiResearch Manufacturing Company of Arizona): Amendment 39-4965. Applicable to all engine models ATF3-6-4C, -6A-3C, and -6A-4C with exhaust deflector liner and seal assembly, Garrett part number (P/N) 3001313-11 through -14, installed. Compliance required as indicated unless already accomplished. To prevent the possibility of an uncontained engine failure, accomplish the following: A. Prior to the accumulation of an additional 5 hours in service, after the effective date of this AD, and at intervals not to exceed 25 operational hours thereafter, until incorporation of the exhaust deflector liner and seal assembly bolted flange system as specified in Section 2.A., "Accomplishment Instructions," of GTEC SB ATF3-72-6092, dated May 25, 1984, or equivalent approved by the Manager, Western Aircraft Certification Office, visually inspect the stationary seal/sixth stage low pressure turbine rotor assembly area of allaffected engines for evidence of seal/rotor contact and/or seal looseness as specified in the following GTEC Light Maintenance Manual Revisions, or equivalent approved by the Manager, Western Aircraft Certification Office: ENGINE MODEL MANUAL REFERENCE ATF3-6-4C Light Maintenance Manual Report No. 72-00-52, Revision 6 dated November 15, 1983; Temporary Revision No. 72-88, 72-00-00, Trouble Shooting dated April 16, 1984; and Temporary Revision No. 72-89, 72-00-00, Trouble Shooting dated April 16, 1984. ATF3-6A-3C Light Maintenance Manual Report No. 72-03-32, Revision 3 dated November 15, 1983; Temporary Revision No. 72-43, 72-00-00, Trouble Shooting dated April 16, 1984; and Temporary Revision No. 72-44, 72-00-00, Trouble Shooting dated April 16, 1984. ATF3-6A-4C Light Maintenance Manual Report No. 72-03-42, Revision 4 dated November 15, 1983; Temporary Revision No. 72-44, 72-00-00, Trouble Shooting dated April 16, 1984; and Temporary Revision No. 72-45, 72-00-00, TroubleShooting dated April 16, 1984. B. Engines with unsuccessful inspection results found during the accomplishment of paragraph A above are to be disassembled as required to modify the exhaust deflector liner and seal assembly and to inspect the sixth stage turbine rotor assembly. C. Upon removal of the sixth stage low pressure turbine rotor assembly from an affected engine for any reason or within 200 operating hours after the effective date of this AD or prior to April 15, 1985, whichever comes first, incorporate the new exhaust deflector liner and seal assembly bolted flange system as specified in Section 2.A., "Accomplishment Instructions," of GTEC SB ATF3-72-6092, dated May 25, 1984, or equivalent approved by the Manager, Western Aircraft Certification Office. Aircraft may be ferried in accordance with the provisions of Federal Aviation Regulations (FARs) 21.197 and 21.199 to a base where the AD can be accomplished. Upon request of an operator, an equivalent meansof compliance with the requirements of this AD may be approved by the Manager, Western Aircraft Certification Office, Northwest Mountain Region, P.O. Box 92007, Worldway Postal Center, Los Angeles, California 90009. The manufacturer's specifications and procedures identified and described in this directive are incorporated herein and made a part hereof pursuant to 5 U.S.C. 552(a)(1). All person affected by this directive who have not already received these documents from the manufacturer may obtain copies upon request to Garrett Turbine Engine Company, P.O. Box 5217, Phoenix, Arizona 85010; telephone (602) 231-1000. These documents also may be examined at Office of the Regional Counsel, New England Region, FAA, 12 New England Executive Park, Burlington, Massachusetts 01803. This amendment supersedes Amendment 39-4900 (49 FR 35614), AD 84-11-51. This amendment becomes effective December 26, 1984, to all persons except those persons to whom it was made immediately effective by telegraphic AD T84-20-51, issued October 4, 1984.
2013-03-02: We are superseding an existing airworthiness directive (AD) for Eurocopter France (Eurocopter) Model EC 155B, EC155B1, SA-365N1, AS-365N2 and AS 365 N3 helicopters. That AD currently requires inspecting certain tail rotor hubs (TRH) for a crack and removing any cracked TRH. This AD requires the same actions but adds more part numbers to the list of affected TRHs. This AD is prompted by further analysis that indicates that additional part-numbered TRHs must be inspected for cracks. The actions specified by this AD are intended to detect a crack in the TRH and prevent the tail rotor from jamming, which could lead to reduced or loss of control of the helicopter.
2013-03-15: We are adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company Models 172R and 172S airplanes. This AD was prompted by reports of chafing of a new configuration of the fuel return line assembly, which was caused by the fuel return line assembly rubbing against the right steering tube assembly during rudder pedal actuation. This AD requires you to install the forward and aft fuel return line support clamps and brackets; inspect for a minimum clearance between the fuel return line assembly and the steering tube assembly and clearance between the fuel return line assembly and the airplane structure; and, if any damage is found, replace the fuel return line assembly. We are issuing this AD to correct the unsafe condition on these products.
98-19-06: This amendment adopts a new airworthiness directive (AD), applicable to certain Saab Model SAAB 2000 series airplanes, that requires replacing the radio tuning units (RTU's) and associated components with new, improved parts. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by this AD are intended to prevent NAV/COM radios from simultaneously changing tuned frequencies and transponder codes due to a black screen failure or "blanking" of an RTU, which could result in loss of communications capability and air traffic control data.
95-12-23: 95-12-23 TWIN COMMANDER AIRCRAFT CORPORATION: Amendment 39-9275; Docket No. 94-CE-29-AD. Applicability: The following airplane models and serial numbers, certificated in any category: Model Serial Numbers 690C 11600 through 11735 695 95000 through 95084 NOTE 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must use the authority provided in paragraph (g) of this AD to request approval from the FAA. This approval may address either no action, if the current configuration eliminates the unsafe condition, or different actions necessary to address the unsafe condition described in this AD. Such a request should include an assessment of the effect of the changed configuration on the unsafe condition addressed by this AD. In no case does the presence of any modification, alteration, or repair remove any airplane from the applicability of this AD. Compliance: Required upon the accumulation of 6,000 hours time-in-service (TIS) or within the next 50 hours TIS after the effective date of this AD, whichever occurs later, unless already accomplished, and thereafter as indicated in the body of this AD. To prevent wing damage caused by fatigue cracking, which, if not detected and corrected, could progress to the point of structural failure, accomplish the following: (a) For all affected serial number Model 695 airplanes, and any Model 690C airplane incorporating a serial number in the 11600 through 11730 range, inspect the wing structure for cracks in accordance with the PART I ACCOMPLISHMENT INSTRUCTIONS (INSPECTIONS) section of Twin Commander Service Bulletin (SB) No. 213, dated July 29, 1994. (b) For any Model 690C airplane incorporating aserial number in the 11731 through 11735 range, inspect the wing structure for cracks in accordance with Item 10 of the PART I ACCOMPLISHMENT INSTRUCTIONS (INSPECTIONS) section of Twin Commander SB No. 213, dated July 29, 1994. (c) If, during the inspections required in paragraphs (a) and (b) of this AD, cracks are found in the areas referenced in Figures 1 through 5 and the instructions of the service information referenced above, prior to further flight, replace the damaged structure and modify the wing structure in accordance with the PART II ACCOMPLISHMENT INSTRUCTIONS (MODIFICATIONS) section of Twin Commander SB No. 213, dated July 29, 1994. (d) If no cracks are found, accomplish one of the following: (1) For all airplanes, upon the accumulation of 7,500 hours TIS or within 1,000 hours TIS after the initial inspection, whichever occurs later, reinspect the structure in accordance with either paragraph (a) or (b) of this AD, as applicable, and reinspect thereafter atintervals not to exceed 1,000 hours TIS, and, if applicable, replace any damaged part or modify the wing structure as specified in paragraph (c) of this AD; or (2) For Model 695 airplanes and any Model 690C airplane incorporating a serial number in the 11600 through 11730 range, prior to further flight, modify the wing structure in accordance with the PART II ACCOMPLISHMENT INSTRUCTIONS (MODIFICATIONS) section of Twin Commander SB No. 213, dated July 29, 1994. (e) For all affected Model 695 airplanes and any Model 690C airplane incorporating a serial number in the 11600 through 11730 range, the modification referenced in paragraphs (c) and (d)(2) of this AD may be accomplished any time after the initial inspection as terminating action for the repetitive inspection requirement of this AD, except for the inspection of the doublers at the wing attach fittings located in the Fuselage Station 144 frame (Item 10 of PART I ACCOMPLISHMENT INSTRUCTIONS section of the Twin Commander SBNo. 213, dated July 29, 1994). All affected model and serial number airplanes must inspect in this area at every 1,000 hours TIS. NOTE 2: For those airplanes that have not accumulated 6,000 hours TIS, the initial and first repetitive inspection required by this AD were established to coincide with the 6,000-hour Major Inspection Guide I and 7,500-hour Major Inspection Guide II inspections, respectively, so that the operator may schedule the required action in accordance with these major inspections. (f) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished. (g) An alternative method of compliance or adjustment of the initial or repetitive compliance times that provides an equivalent level of safety may be approved by the Manager, Seattle Aircraft Certification Office (ACO), FAA, Northwest Mountain Region, 1601 Lind Avenue S.W., Renton, Washington 98055-4056. The request shall be forwarded through an appropriate FAA Maintenance Inspector, who may add comments and then send it to the Manager, Seattle ACO. NOTE 3: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Seattle ACO. (h) The inspections and modification required by this AD shall be done in accordance with Twin Commander Service Bulletin No. 213, dated July 29, 1994. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Twin Commander Aircraft Corporation, 19003 59th Drive, NE., Arlington, Washington 98223. Copies may be inspected at the FAA, Central Region, Office of the Assistant Chief Counsel, Room 1558, 601 E. 12th Street, Kansas City, Missouri, or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. (i) This amendment becomes effective on July 30, 1995.
81-16-02: 81-16-02 DOWTY ROTOL, LTD.: Amendment 39-4170. Applies to the 7 Dowty Rotol propeller types listed which have Mod. No. (c)VP2833 (Service Bulletin 61-838) or Mod. No. (c)VP2866 (Service Bulletin 61-889) incorporated, as installed on, but not limited to the airplane models shown, and pitch lock cylinders and lock support sleeves, P/N 601027277, held as spares. (Note: This AD does not apply to propellers Serial No. DRG 67/78 and subsequent or any pitch lock assembly having a 3/4 inch white paint spot on the cylinder cover.) Propeller Type Installed Airplane Model R184/4-30-4/50 Grumman G-159 R193/4-30-4/50 & 61 Fairchild F-27A, F, G, and J Fokker F-27 Mks 200, 400, 500 & 600 Fairchild Hiller FH-227 Series R257/4-30-4/60 Fairchild F-27M Fairchild Hiller FH-227 B, C, D & E R209/4-40-4.5/2 YS11 & 11A R245/4-40-4.5/13 GD/Convair 240 with STC # SA1054WE installed GD/Convair 340/440 with STC # SA1096WE installed R259/4-40-4.5/17 GD/Convair 340/440 with STC #SA1096WE installed R179/4-20-4/33 Viscount 810 Series Compliance is required as indicated, unless already accomplished. To prevent cracks in the propeller pitch lock cylinder, accomplish the following one-time only actions: (a) Within the next 1,000 hours time in service after the effective date of this AD, or at the next propeller overhaul, whichever occurs first, inspect the propeller pitch lock cylinder for cracks in accordance with paragraph 2.A., "Accomplishment Instructions," of Dowty Rotol Service Bulletin 61-906, Revision 4, dated June 12, 1980 (hereinafter referred to as service bulletin), or an FAA-approved equivalent, and - (1) If any cracks are found, before further flight, remove the pitch lock cylinder from service and replace it with a crack-free pitch lock cylinder of the same part number, which has been inspected and, if necessary, reworked and reprotected in accordance with paragraphs (b) and (c) of this AD. (2) If no cracks are found, comply with paragraphs (b) and (c) of this AD before further flight. (b) Inspect the chamfer around the snout adjacent to the radius at the base of the bore at the forward end of the pitch lock cylinder in accordance with paragraph 2.A.(5) of the service bulletin, or an FAA-approved equivalent, and - (1) If the chamfer is found to be within the dimensions shown in Figure 2 of the service bulletin, or an FAA-approved equivalent, the pitch lock cylinder may be returned to service. (2) If the chamfer is found to be outside the dimensions shown in Figure 2 of the service bulletin, or an FAA-approved equivalent, rework and reprotect it in accordance with paragraph 2.A.(5) of the service bulletin or an FAA-approved equivalent, before returning the pitch lock cylinder to service. (c) Inspect the large internal chamfer at the rear end of the lock support sleeve, P/N 601027277, in accordance with Paragraph 2.A.(6) of the service bulletin, or an FAA-approved equivalent, and - (1) If the dimensions are found to be within the dimensions shown in Figure 3 of the service bulletin, or an FAA-approved equivalent, the lock support sleeve may be returned to service. (2) If the dimensions are found to be outside the dimensions shown in Figure 3 of the service bulletin, or an FAA-approved equivalent, rework and reprotect the lock support sleeve, P/N 601027277, in accordance with paragraph 2.A.(6) of the service bulletin, or an FAA- approved equivalent, before returning the lock support sleeve to service. (d) Before releasing to service any pitch lock cylinders held as spares, irrespective of part number, inspect them and remove from spares or rework and reprotect, as required, in accordance with paragraphs (a) and (b) of this AD. (e) Before releasing to service any support sleeves, P/N 601027277, held as spares, inspect them and remove from spares or rework and reprotect, as required, in accordance with paragraph (c) of this AD. Upon request of an operator, the Chief, Engineering and Manufacturing Branch, AGL- 210, Federal Aviation Administration, Great Lakes Region, may adjust the compliance time specified in paragraph (a) of this AD provided such requests are made through an FAA maintenance inspector, and the request contains substantiating data to justify the request for that operator. For purposes of this AD, an FAA-approved equivalent must be approved by the Chief, Engineering and Manufacturing Branch, AGL-210, Federal Aviation Administration, Great Lakes Region. The manufacturer's specifications and procedures identified in this directive are incorporated herein and made part hereof pursuant to 5 U.S.C. 552(a)(1). All persons affected by the directive who have not already received these documents from the manufacturer may obtain copies upon request to Dowty Rotol, Inc., Staverton West, Sulley Road, Box 5000, Sterling, VA 22170 or Dowty Rotol, Ltd., Cheltenham Road, Gloucester, England GL2 9QH. These documents may also be examined at the Great Lakes Regional Office, FAA, 2300 East Devon Avenue, Des Plaines, Illinois 60018. This amendment becomes effective July 28, 1981.
2013-01-05: We are adopting a new airworthiness directive (AD) for Eurocopter France (Eurocopter) Model AS350B3 and EC130B4 helicopters. This AD requires revising the Limitations section of the Rotorcraft Flight Manual (RFM) to reduce the starter generator operating current to 180 amperes (amps) and installing a placard in the instrument panel indicating the revised limitation. This AD was prompted by the determination that the manufacturer-installed Aircraft Parts Corporation (APC) starter generator has exceeded the shaft horse power extractions allowed for Turbomeca engines. The actions of this AD are intended to prevent the engine surge margin being reduced, which can result in engine failure.
98-18-26: This amendment adopts a new airworthiness directive (AD), applicable to certain Airbus Model A320 series airplanes, that requires repetitive inspections to detect fatigue cracking of the front spar vertical stringers on the wings; and repair, if necessary. This amendment also provides for an optional terminating action for the repetitive inspections. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by this AD are intended to detect and correct fatigue cracking of the front spar vertical stringers on the wings, which could result in reduced structural integrity of the airframe.