Aircraft-logs.com

Results
2006-22-08: The FAA adopts a new airworthiness directive (AD) for all Air Tractor, Inc. Models AT-602, AT-802, and AT-802A airplanes. This AD requires you to repetitively inspect the engine mount for any cracks, repair or replace any cracked engine mount, and report any cracks found to the FAA. This AD results from reports of cracked engine mounts. We are issuing this AD to detect and correct cracks in the engine mount, which could result in failure of the engine mount. Such failure could lead to separation of the engine from the airplane.
2021-12-15: The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-243, A330-243F, A330-341, A330-342, and A330-343 airplanes. This AD was prompted by a report of an in-flight turnback due to loss of green and blue hydraulic systems in cruise. This AD requires inspecting for discrepancies of the hydraulic pressure switch harnesses of affected engines, and applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2018-20-06: We are superseding Airworthiness Directive (AD) 2016-25-03, which applied to certain Airbus Model A300 F4-600R series airplanes. AD 2016-25-03 required repetitive high frequency eddy current (HFEC) inspections of the aft lower deck cargo door (LDCD) frame forks; a one- time check of the LDCD clearances; and a one-time detailed visual inspection of hooks, eccentric bushes, and x-stops; and corrective actions if necessary. This AD requires repetitive HFEC inspections of the aft LDCD frame forks; a one-time check of the LDCD clearances; and a one-time detailed visual inspection of hooks, eccentric bushes, and x-stops; and corrective actions if necessary. This AD was prompted by a report of two adjacent frame forks that were found cracked on the aft LDCD of two airplanes during scheduled maintenance, and the introduction of frame fork reinforcement or repair procedures that, when done, allow an extension of repetitive inspection intervals. We are issuing this AD to address the unsafe condition on these products.
2006-22-07: The FAA is adopting a new airworthiness directive (AD) for all Airbus Model A300 and A310 airplanes and A300-600 series airplanes. This AD requires inspecting for discrepancies of all electrical bundles located in the leading and trailing edges of the wings, and performing corrective actions if necessary. This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent an ignition source, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.
2021-11-01: The FAA is superseding Airworthiness Directive (AD) 2013-20-13 for certain Bell Helicopter Textron Canada Limited (now Bell Textron Canada Limited) (Bell) Model 206B and 206L helicopters. AD 2013-20-13 required installing a placard beneath the engine power dual tachometer and revising the Operating Limitations section of the existing Rotorcraft Flight Manual (RFM) for your helicopter. This AD was prompted by the engine manufacturer expanding the RPM (N2) steady-state operation avoidance range limits. This AD retains certain requirements of AD 2013-20-13, and requires revising certain sections of the existing RFM for your helicopter and installing or replacing a placard. The FAA is issuing this AD to address the unsafe condition on these products.
2021-12-10: The FAA is adopting a new airworthiness directive (AD) for Leonardo S.p.a. Model AB139 and AW139 helicopters with 3-stretcher kit part number 139084-501 installed. This AD was prompted by a report of a design deficiency which affects the primary stretcher unit of the 3- stretcher kit. This AD requires installing a placard on the primary stretcher. The FAA is issuing this AD to address the unsafe condition on these products.
2018-19-29: We are adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-200 Freighter, -200, and -300 series airplanes; and Airbus SAS Model A340-200, -300, -500, and -600 series airplanes. This AD was prompted by a report of deficient fatigue performance of high strength steel used in forgings. Components made from the affected high strength steel are installed on the main landing gear (MLG), nose landing gear (NLG), and center landing gear (CLG). This AD requires identifying the part number and serial number of certain components installed on the MLG, NLG, and CLG; replacing affected parts; identifying the airplane's weight variant; and determining the applicable life limit for certain components installed on the MLG, NLG, and CLG. We are issuing this AD to address the unsafe condition on these products.
85-23-05: 85-23-05 BELL HELICOPTER TEXTRON, INC.: Letter issued November 8, 1985. Applies to all Bell Helicopter Model 214B and 214ST series helicopters certified in all categories that have collective sleeve part number 214-010-411-001 or -003 with serial number Al9-00001 through Al9-00738 or serial number A-1 through A-10 installed. Compliance is required before further flight after receipt of this AD, unless previously accomplished, and thereafter at 250 hour intervals. To prevent failure of the collective sleeve, accomplish the following: a. Before further flight after receipt of this priority letter AD, perform a magnetic particle inspection of the affected sleeves using the procedures described in Bell Alert Service Bulletin 214-84-26, dated March 12, 1984, or 214ST-84-17, dated March 12, 1984, as appropriate. NOTE: It is essential that the paint and primer be removed as described in the service bulletins prior to performing the magnetic particle inspection.b. Repeat the magnetic particle inspection every 250 hours time in service. c. If cracks are found, replace with serviceable parts. d. An alternative means of compliance or adjustment of the compliance time, which provides an equivalent level of safety, must be approved by the Manager, Helicopter Certification Branch, Aircraft Certification Division, FAA, Southwest Region. This airworthiness directive is effective upon receipt.
2006-22-11: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as unsatisfactory initial elevator trim actuator greasing, which may lead to the icing of the elevator trim and generate an untrimmed nose-up attitude after an autopilot disconnection. We are issuing this AD to require actions to correct the unsafe condition on these products.
2006-22-02: The FAA is superseding an existing airworthiness directive (AD), which applies to certain Airbus Model A300-600 series airplanes. That AD currently requires an inspection for evidence of chafing between the hydraulic flexible hose and the ram air turbine (RAT) hub, and related investigative and corrective actions if necessary. This new AD extends the applicability to include all Model A300-600 series airplanes that are equipped with a certain RAT. This AD results from reports of holes in the RAT hub cover. We are issuing this AD to prevent a hole in the RAT hub cover. A hole in the RAT hub cover could allow water to enter the RAT governing mechanism, freeze during flight, and jam the governing mechanism. In addition, the metal particles that result from chafing between the hydraulic flexible hose and the RAT could mix with the lubricant grease and degrade the governing mechanism. In an emergency, a jammed or degraded RAT could result in its failure to deploy, loss of hydraulicpressure or electrical power to the airplane, and consequent reduced controllability of the airplane. DATES: This AD becomes effective December 1, 2006. The Director of the Federal Register approved the incorporation by reference of a certain publication listed in the AD as of December 1, 2006. On August 26, 2005 (70 FR 42267, July 22, 2005), the Director of the Federal Register approved the incorporation by reference of Airbus Service Bulletin A300-29-6054, Revision 01, excluding Appendix 01, dated November 4, 2004.