Results
77-13-07: 77-13-07 BEECH: Amendment 39-2932. Applies to Model 200 (Serial Numbers BB-2 thru BB-250) airplanes certificated in all categories. Compliance: Required as indicated, unless already accomplished. To assure that wings will carry the 50 feet/second gust design loads, within 50 hours' time in service after the effective date of this AD, accomplish the following: A) With aileron control system pinned in the neutral position rerig the droop of right and left aileron to zero degrees, with a tolerance of plus one-half degree up, minus zero degrees down in accordance with Beechcraft Service Instructions Number 0906 or later approved revisions. B) Any equivalent method of compliance with this AD must be approved by the Chief, Engineering and Manufacturing Branch, FAA, Central Region. This amendment becomes effective July 1, 1977.
55-13-01: 55-13-01 PIPER: Applies to Model PA-23, Serial Numbers 23-160 to 23-162 Inclusive, 23-166 to 23-168 Inclusive, 23-170, 23-172, 23-177, 23-193 to 23-219 Inclusive, 23-221 to 23- 224 Inclusive, 23-226 to 23-229 Inclusive, 23-231 to 23-234 Inclusive, and 23-237. Compliance required by August 1, 1955. It has been found that all the PA-23 Models listed above have installed two flexible fuel valve controls that have been found to flex excessively at the splice. The addition of an idler bellcrank should be accomplished by the use of Piper Kit No. 754 103 and the instructions included. Owners of PA-23's with auxiliary fuel tanks must not operate the auxiliary fuel system until this modification has been accomplished. (Piper Immediate Action Service Bulletin No. 139 applies to this malfunction.)
2017-18-19: We are adopting a new airworthiness directive (AD) for all Airbus Model A310-203, -204, -221, -222, -304, -322, -324, and -325 airplanes. This AD was prompted by reports of cracking in the drainage holes on the lower skin panel in the center wing box between frames (FR) 42 and FR46. This AD requires repetitive rotating probe inspections for cracking of the trellis boom drainage holes, the holes in the stringers bottom, and the holes of the inner pump, and corrective actions if necessary. We are issuing this AD to address the unsafe condition on these products.
2017-18-16: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-700 and -700C series airplanes. This AD was prompted by a report that, for certain airplanes, the nose-up pitch trim limit and associated warning will allow the horizontal stabilizer position to be set outside acceptable limits for a mis-trimmed takeoff condition. This AD requires, depending on airplane configuration, replacing certain pitch trim light plates, relocating certain position warning horn switches, revising certain software, removing a certain placard, and doing related investigative and corrective actions if necessary. We are issuing this AD to address the unsafe condition on these products.
53-04-01: 53-04-01 PIPER: Applies to All Model PA-18 Aircraft Which Have Not Had the Control Stick Retention Device Modified to Incorporate a Through Bolt. Compliance required by April 1, 1953. In order to prevent the control stick inadvertently pulling out of the socket, continue the existing hole for the retention pin on the quick detachable control stick spring device through the control stick and socket and install an AN 3-14 or AN 3-14A through bolt. (Piper Service Letter No. 162 dated March 6, 1951, covers this same subject.)
54-02-02: 54-02-02 FEDERAL SKIS: Applies to All Universal (Stinson) 108 and Cessna 170, 170A and 170B Airplanes Equipped With Federal Models AWB-2500 and AWB-2500A Wheel Skis and Piper PA-20 Airplanes Equipped With Federal Model AWB-2100 Wheel Skis. Compliance required as soon as possible but not later than February 15, 1954. To preclude the possibility of the ski dropping down against the mechanical rigger and possible subsequent damage to the aircraft structure, the rigging arrangement must be revised in accordance with Federal Aircraft Works Drawing No. 11D1077.
77-13-04: 77-13-04 GRUMMAN-AMERICAN: Amendment 39-2931. Applies to G-164B, S/N's 138B, 142B, 177B and up, and G-164A, S/N's 1686, 1695 and up, certificated in all categories. Accomplish the following, unless previously accomplished: a) Before further flight, install a placard adjacent to the parking brake handle stating: "Warning - Parking Brake OFF Prior to Landing." b) Within the next 50 hours in service, install the alteration defined in Grumman American Aviation Corporation Service Bulletin No. 60, dated May 20, 1977, or an equivalent method approved by the Chief, Engineering and Manufacturing Branch, FAA Eastern Region. When this is accomplished, the warning placard may be removed. This Amendment becomes effective June 29, 1977.
2017-18-10: We are adopting a new airworthiness directive (AD) for certain Diamond Aircraft Industries GmbH Models DA 42, DA 42 M-NG, and DA 42 NG airplanes. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as crack formation on the flap bell crank, which could cause the flap bell crank to fail. We are issuing this AD to require actions to address the unsafe condition on these products.
51-27-02: 51-27-02 BOEING: Applies to all Model B-377 Aircraft equipped with Goodrich H-3-626 and H-3-650 Wheel Assemblies. To be accomplished as indicated below. As a precautionary measure to preclude serious hazards which may result from fatigue cracks in Goodrich H-3-626 and H-3-650 wheel assemblies, all wheels shall be carefully inspected with at least a 4x magnifying glass at the periodic inspection following each 50th landing. These inspections shall be conducted until the wheels must be retired from service. The wheels must be retired at the time replacement wheels are made available. Due to the fact that a large quantity of B-377 wheel halves were delivered to the operators without being assigned a serial number, the following description will identify both the wheel to be replaced and also the replacement wheel. The wheels to be retired from service are those wheels which have a tapered spoke and no reinforcing beading around the inner side of the spoke cutout area. Replacement wheels are those wheels which have a reinforcing bead around the inner side of the spoke cut-out area and have either straight or tapered spokes. (Goodrich Service Bulletin No. 27, dated November 14, 1951, covers this identification problem in further detail.) Type I - Cracks Progressing Across a Spoke. The wheel should be rejected when there is more than one crack of this type to a spoke, when there is more than one crack in each spoke cutout, or when a crack is in excess of 1 inch in length. Type II - Cracks Progressing Radially Across the Brake Drum Mounting Flange. More than one crack of this type in any one spoke cutout will be cause for rejection. Type III - Cracks in the Tie Bolt Recess and the Junction of the Drum Mounting Area. This type crack is in a noncritical area and is cause for wheel rejection only when either of the following conditions occur: 1. The crack extends to the spoke cutout. 2. Developed cracks on either side of the recess progress to within 1 3/8 inches of each other. The above wheel crack limitations are based on the recommendations of the B. F. Goodrich Co. (Goodrich Service Bulletin No. 17 covers this subject and illustrates the three types of wheel cracks.)
2017-16-07: We are adopting a new airworthiness directive (AD) for all Airbus Model A330-200, A330-200 Freighter, A330-300, A340-500, and A340-600 series airplanes; and A340-313 airplanes. This AD was prompted by the discovery of Tartaric Sulfuric Anodizing (TSA)/Chromic Acid Anodizing (CAA) surface treatment in certain bulk cargo door frame holes of certain airplanes. This AD requires inspection of the fuselage bulk cargo door frames at specific locations, and corrective action if necessary. We are issuing this AD to address the unsafe condition on these products.
65-28-02: 65-28-02 FAIRCHILD: Amdt. 39-169 Part 39 Federal Register December 14, 1965. Applies to Model F-27 Series Airplanes Incorporating Upper Engine Mount Fittings P/N's 27-503148-31, -32, -41, -42, -51, -52, -61, -62, and Lower Engine Mount Fittings P/N's 27-503149-11, -12, -31, -32, -41, and -42. Compliance required as indicated. To detect cracks in the engine mount attachment fittings, accomplish the following: (a) Within the next 50 hours' time in service after the effective date of this AD, unless already accomplished within the 250 hours' time in service before the effective date of this AD, inspect the engine mount fittings in accordance with (d). (b) For engine mount fittings with 10,000 or more hours' time in service on the effective date of this AD, reinspect in accordance with (d) at intervals not to exceed 300 hours' time in service from the last inspection. (c) For engine mount fittings with less than 10,000 hours' time in service on the effective date of this AD, reinspect in accordance with (d) before the accumulation of 10,150 hours' time in service, unless accomplished after the accumulation of 9,850 hours' time in service, and thereafter at intervals not to exceed 300 hours' time in service from the last inspection. (d) Visually inspect for cracks each engine mount fitting (eight per airplane), on the forward side of the firewall, including all welds, using at least a 10-power glass or an FAA-approved equivalent. Clean all surfaces of each engine mount fitting prior to inspecting, (without removing fitting). (e) If a crack is found during the inspection specified in (d) before further flight, replace the engine mount fitting with a part of the same part number that has been inspected in accordance with (d), or an equivalent part approved by the Chief, Engineering and Manufacturing Branch, FAA Eastern Region. (f) Upon request of the operator, an FAA maintenance inspector, subject to prior approval of the Chief,Engineering and Manufacturing Branch, FAA Eastern Region, may adjust the repetitive inspection intervals specified in this AD to permit compliance at an established inspection period of the operator if the request contains substantiating data to justify the increase for such operator. This directive effective December 14, 1965.
2017-17-18: We are adopting a new airworthiness directive (AD) for certain General Electric Company (GE) CF34-8 model turbofan engines. This AD was prompted by analysis that resulted in the reduction of the life of the affected fan blades. This AD requires inspections of the affected fan blades until their removal. We are issuing this AD to address the unsafe condition on these products.
51-27-03: 51-27-03 PIPER: Applies to All Model PA-22 Aircraft, Serial Numbers 22-1 Through 22-354. Compliance should be made before next flight in freezing temperature, but not later than December 15, 1951. Driving rain or washing may cause an accumulation of water in nose wheel oleo housing which can freeze in lower bearing and render rudder system inoperative. To provide drainage, locate a 3/16-inch hole on aft side of nose wheel oleo housing, P/N 13035, centered 9/16-inch above lower edge of housing. Unless oleo strut is removed from housing, use extreme care not to damage oleo strut while drilling drain hole. Insure strut is drained. Fill upper end of housing and upper bearing area with generous amount of cup grease to seal against water. (Piper Service Bulletin No. 119, dated November 7, 1951, covers this same subject.)
52-12-01: 52-12-01 BOEING: Applies to all Model 377 Aircraft. Compliance required as specified below. In order to reduce the hazard of fire resulting from overheating of the freon compressor motors, compliance with the following is required: A. Compliance required before any installation of overhauled or new compressor motor after October 1, 1952. (Not required if item B accomplished or airplane operated in accordance item C.) Replace the following Westinghouse compressor motor magnesium parts with corresponding aluminum parts: . . . . . . . . . . . . . . . . . P/N (Mg.) P/N (AL.) Inlet Cooling Cap P14A9709 P35A9046 Front Bearing Bracket P14A9712 P35A9044 Fan A14B3724 P35A9042 B. Compliance required prior to October 1, 1952. (Not required if both motors previously modified in accordance item A or if airplane operated in accordance item C.) Install a temperature sensing switch, adjusted to actuate at 100 degrees or less, in the cooling air outlet of each freon compressor motor. Install circuits and equipment so that this overheat switch, as well as the motor thermoguard switch, will illuminate a cockpit warning light or will open the compressor motor power circuit, or both. C. In the event the modifications outlined in A or B are not completed in accordance with the above requirements, aircraft may be operated with the refrigeration systems made inoperative.
59-14-01: 59-14-01\tBOEING: Applies to the following Boeing 707-100 Series Aircraft Serial Numbers 17586 through 17591, 17609, 17628 through 17637 and 17658 through 17662. \n\tCompliance required as indicated. \n\tAs a result of the complete loss of hydraulic fluid in the utility hydraulic system of a 707- 100 series aircraft caused by the rupture of the aluminum tube assembly in the nose wheel well door-open system, the following modification shall be accomplished. Prior to July 31, 1959, the nose wheel door-open aluminum tube assembly 50-6848-45 shall be replaced with corrosion resistant steel tubing 3/8 inch O.D. by 0.028 inch wall thickness. \n\t(Boeing Service Bulletin No. 412 pertains to this same subject.)
66-05-01: 66-05-01 CURTISS-WRIGHT: Amdt. 39-183 Part 39 Federal Register January 26, 1966. Applies to Model C-46 Series airplanes. Compliance required as indicated. To prevent failure of the main landing gear drag struts, accomplish the following, unless already accomplished: (a) Within the next 200 hours' time in service after the effective date of this AD, inspect the weld in the main landing gear drag strut that joins the lower end fittings, P/N 20-310- 1018-2, to the drag strut tubes, P/N's 20-310-1017-7 and -8, for the presence of a space or notch formed by the filleted shoulder on the end fitting and the weld. If the weld bead does not extend from the strut to the outer edge on the shoulder of the fitting, completely filling the area between the tube and the shoulder, this area must be inspected for external and internal cracks using X-ray or an FAA-approved equivalent. If cracks are found, the drag strut must be replaced before further flight. (b) When inspected inaccordance with (a), if the weld bead extends from the drag strut tube, P/N's 20-310-1017-7 and -8, to the outer edge on the shoulder of the lower end fitting, P/N 20-310-1018-2, completely filling the area between the tube and the shoulder, no further inspections are required by this AD. (c) When inspected in accordance with (a), if the weld bead does not extend from the drag strut tube, P/N's 20-310-1017-7 and -8, to the outer edge on the shoulder of the lower end fitting, P/N 20-310-1018-2, completely filling the area between the tube and the shoulder, compliance with (c)(1) or (2) is required. (1) Reinspect struts, inspected in accordance with (a) at intervals not exceeding 400 hours' time in service from the last inspection. Replace cracked parts before further flight. (2) Fill in the space or notch between the tube and the shoulder using an FAA-approved method or replace the affected assembly with an assembly on which the space or notch does not exist. If the space or notch is filled in or if the affected part is replaced with an assembly on which the space or notch does not exist, no further inspections are required by this AD. (d) Upon request of the operator, an FAA maintenance inspector, subject to prior approval of the Chief, Engineering and Manufacturing Branch, FAA Southern Region, may adjust the repetitive inspection intervals specified in this AD to permit compliance at an established inspection period of the operator if the request contains substantiating data to justify the increase for such operator. This supersedes AD 61-22-5. This directive effective February 25, 1966.
2017-18-08: We are adopting a new airworthiness directive (AD) for all Dassault Aviation Model FALCON 2000 and FALCON 2000EX airplanes. This AD was prompted by reports of ice accretion on the airplane wing due to the failure of certain anti-ice piccolo tubes in the wing outboard slats. This AD requires repetitive inspections of each anti-ice piccolo tube and corrective action if necessary. We are issuing this AD to address the unsafe condition on these products.
2017-17-12: We are adopting a new airworthiness directive (AD) for all Airbus Model A310-203, -221, -222, -304, -322, -324, and -325 airplanes. This AD was prompted by an evaluation by the design approval holder indicating that the wing bottom skin at the main landing gear (MLG) reinforcing plate is subject to widespread fatigue damage (WFD). This AD requires a modification of the wing bottom skin at the MLG reinforcing plate. We are issuing this AD to address the unsafe condition on these products.
67-22-05: 67-22-05 BRITISH AIRCRAFT: Amdt. No. 39-447, Part 39, Federal Register July 20, 1967. Applies to Models BAC 1-11 203/AE, 204/AF, 212/AR, 401/AK, and 410/AQ Series Airplanes. Compliance required as indicated. To prevent the use of unserviceable dropout oxygen mask face pieces, accomplish the following: (a) Within the next 600 hours' time in service after the effective date of this AD, unless already accomplished within the last 600 hours' time in service, and thereafter at intervals not to exceed 1,200 hours' time in service from the last inspection, visually examine all oxygen mask face pieces, Part Nos. WK 28420, WK 28171, and WK 31342, for deterioration in accordance with BAC 1-11 Alert Service Bulletin 35-A-PM 2795, Issue No. 1, dated January 16, 1967, or later ARB-approved issue, or FAA-approved equivalent. (b) Replace deteriorated oxygen mask face pieces found during the inspections required by paragraph (a) with either serviceable face pieces of the same partnumber or modified face pieces, Walter Kidde Part Nos. WK 33298, WK 33299, and WK 33300, in accordance with BAC Service Bulletin 35-PM 2795, or later ARB-approved issue, or FAA-approved equivalent, before further flight. (c) The repetitive inspections required by paragraph (a) may be discontinued when the oxygen face mask pieces are modified in accordance with BAC Service Bulletin 35-PM 2795, or later ARB-approved issue, or FAA-approved equivalent. This amendment effective August 19, 1967.
2017-17-08: We are adopting a new airworthiness directive (AD) for certain Airbus Model A330-200, -200 Freighter, and -300 series airplanes; and Model A340-500 and -600 series airplanes. This AD was prompted by a quality control review on the final assembly line, which determined that the wrong aluminum alloy was used to manufacture several structural parts. This AD requires a one-time eddy current conductivity measurement of certain cabin and cargo compartment structural parts to determine if an incorrect aluminum alloy was used, and replacement of any affected part with a serviceable part. We are issuing this AD to address the unsafe condition on these products.
2017-17-11: We are adopting a new airworthiness directive (AD) for certain Dassault Aviation Model FALCON 7X airplanes. This AD was prompted by a report indicating that, under certain operational takeoff conditions, the available thrust in relation with the N1 indication is less than a certified value, which could affect the safety margins with an engine failure during takeoff. This AD requires modifying each engine by updating the electronic engine control (EEC) software and adjusting the engine N1 trim value, and revising the airplane flight manual (AFM). We are issuing this AD to address the unsafe condition on these products.
55-21-02: 55-21-02 PIPER: Applies to All Model PA-23 Aircraft Through Serial Number 23-321, Except Serial Numbers 23-310, -311, -315, and -319. Compliance required as indicated. The wing front spar attachment fitting P/N 17079 at the centerline of the fuselage must be inspected and reinforced as indicated below. This is a welded steel fitting bolted to the front face of the front spar web and is accessible through the wing bottom access panel. I. Compliance required prior to next flight and at every 15 hours thereafter. Visually inspect the wing front spar attachment fitting and if any damage is found such as bent flanges or any other visible distortion contact the Piper Corp. for further instruction prior to returning airplane to flight status. II. Compliance required prior to November 1, 1955. If inspection of item I discloses no defects install reinforcement fitting assembly in accordance with Piper reinforcement Kit 754112 or equivalent. The inspections required in item I are not required after incorporating the fitting reinforcement. (Piper Service Bulletin No. 142 dated October 4, 1955, covers this same subject.)
67-09-02: 67-09-02 BRANTLY: Amdt. 39-373 Part 39 Federal Register March 21, 1967. Applies to Models B-2, B-2A, and B-2B Helicopters with P/N B2-324 Transmission Serial Numbers Prior to Serial Number 307. Compliance required as indicated. To improve the service life and reliability of the upper main rotor mast bearing, within the next 100 hours' time in service after the effective date of this AD, remove the Fafnir P/N 212K bearing presently installed and replace it with an Indiana Gear Works P/N 4524A56, Revision E, sealed bearing. This substitution is to be accomplished as prescribed by Brantly Helicopter Company Service Bulletin No. 21 and applicable sections of the Model B-2 Series helicopter maintenance manuals. This directive effective April 20, 1967
54-20-01: 54-20-01 AIRCRAFT BELT AND TRIM (SAFETY BELT): Applies to Model LBM-1900 (Dwg. No. 19001) Safety Belts Manufactured Prior to April 1, 1954. Compliance required as soon as possible but not later than March 1, 1955. Based on a complaint alleging noncompliance with strength standards of FAA Technical Standard Order C22, verification tests were conducted by the National Bureau of Standards at FAA request, which revealed that the belt assemblies of this make and model manufactured prior to April 1, 1954, with LBM-1900-3 and -3A buckles, were under strength for a majority of specimens tested. These tests are considered as evidence of nonconformance with terms of the TSO. Therefore, TSO-labeled belts of this model as noted above which were manufactured prior to April 1, 1954, can no longer be considered as complying with the prescribed airworthiness standards and, accordingly, must not be used in civil aircraft. Belts of this model manufactured subsequent to April 1,1954, incorporate a buckle of improved design and tests reveal this belt assembly to be in accordance with TSO-C22 tension test requirements. This supersedes AD 54-03-01.
66-29-01: 66-29-01 BOEING: Amdt. 39-301 Part 39 Federal Register November 5, 1966. Applies to Model 727 Series Airplanes. \n\n\tCompliance required as indicated. \n\n\tTo prevent loss of the cowl panels in flight, and resulting damage to the aircraft structure, accomplish the following or an equivalent approved by the Chief, Aircraft Engineering Division, FAA Western Region: \n\n\t(a)\tWithin the next 1,500 hours' time in service after the effective date of this AD, unless already accomplished, modify the side engine cowl panel latch assemblies in accordance with Boeing Service Bulletin No. 71-14 or later FAA-approved revision. Replacement of Hartwell Manufacturing Company hook latch spring, P/N 104914-1, with P/N 106054-1 is optional. \n\n\t(b)\tWithin the next 3,000 hours' time in service after the effective date of this AD, unless already accomplished, modify the center engine cowl panel latch frames in accordance with Boeing Service Bulletin No. 71-27 or later FAA-approved revision. \n\n\tThisdirective effective December 5, 1966.