Results
2007-05-02: The FAA is adopting a new airworthiness directive (AD) for all EMBRAER Model ERJ 170 and ERJ 190 airplanes. This AD requires repetitive detailed inspections for blockage of the pitot drain holes of certain air data smart probes (ADSPs), removing accumulated moisture from the pneumatic passages of the ADSPs, related investigative actions, and corrective actions if necessary. This AD results from reports of erroneous air speed indications caused by blockage of the pitot sensors due to freezing of accumulated moisture in the ADSP pneumatic passages. We are issuing this AD to prevent an erroneous air speed indication, which could reduce the flightcrew's ability to control the airplane.
2021-11-07: The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) GEnx-1B64, 1B64/P1, -1B64/P2, - 1B67, -1B67/P1, -1B67/P2, -1B70, -1B70/75/P1, -1B70/75/P2, -1B70/P1, - 1B70/P2, -1B70C/P1, -1B70C/P2, -1B74/75/P1, -1B74/75/P2, -1B76/P2, - 1B76A/P2, -2B67, -2B67/P, and -2B67B model turbofan engines. This AD was prompted by a finding during an inspection by the manufacturer that two stages 6-10 compressor rotor spools in the high-pressure compressor (HPC) assembly were damaged at similar locations. Additionally, the manufacturer reported that certain stages 6-10 compressor rotor spool webs did not undergo a required fluorescent penetrant inspection (FPI) during production. This AD requires inspection of the stages 6-10 compressor rotor spool and, depending on the results of the inspection, replacement of the stages 6-10 compressor rotor spool. The FAA is issuing this AD to address the unsafe condition on these products.
2007-04-22: The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-100 (as described above), DHC-8-200, and DHC-8-300 series airplanes. This AD requires doing a one-time inspection for damage of the electrical cable harness assembly located on the left and right wing root-to-fuselage aft seal, and repair if necessary; and reworking the fuselage aft seal assembly (left and right) to create a clearance between the electrical cable assemblies and the edge of the fairing panel. This AD results from a report that an airplane encountered an uncommanded propeller feathering during climb, which resulted in an emergency landing. We are issuing this AD to prevent chafing or grounding of the wiring against the aft seal assemblies, which, if not corrected, could interrupt the operation of various systems, including the propeller feather control, alternating current (AC) electrical power, and standby hydraulic power, and result in reduced controllability of the airplane.
2021-12-04: The FAA is adopting a new airworthiness directive (AD) for all Fokker Services B.V. Model F28 Mark 0070 and 0100 airplanes. This AD was prompted by a report that corrosion was found on the horizontal flange on the front spar lower boom, between the rebate strap and the lower boom, and \n\n((Page 33106)) \n\nresulted in bulging. This AD requires doing a detailed visual inspection to detect any bulging, loose, and missing countersunk fastener heads at the left-(LH) and right-hand (RH) outer wing lower skin of the front spar between certain wing stations, and applicable on-condition actions, as specified in a European Union Aviation Safety Agency (EASA), which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2007-04-20: The FAA is adopting a new airworthiness directive (AD) for certain EMBRAER Model ERJ 170-100 LR, -100 STD, -100 SE, -100 SU, -200 LR, -200 STD, and -200 SU airplanes and Model ERJ 190 airplanes. This AD requires inspecting to determine the part number and serial number of the deployment actuator of the ram air turbine (RAT) and related investigative and corrective actions if necessary. This AD results from reports that the RAT may not fully deploy due to galling between the piston rod and gland housing of the RAT deployment actuator. We are issuing this AD to prevent the RAT from failing to deploy, which could result in loss of control of the airplane during in-flight emergencies.
2021-11-22: The FAA is superseding Airworthiness Directive (AD) 2016-11-21 for Airbus Helicopters Deutschland GmbH (Airbus Helicopters) Model EC135P1, EC135P2, EC135P2+, EC135T1, EC135T2, and EC135T2+ helicopters. AD 2016-11-21 required revising the life limit of certain parts and removing each part that has reached its life limit. This AD continues to require revising the life limits for certain parts and removing each part that has reached or exceeded its life limit and expands the applicability to include Model EC135P3 and EC135T3 helicopters. This AD was prompted by the certification of new helicopter models since AD 2016-11-21 was issued. The FAA is issuing this AD to address the unsafe condition on these products.
2007-04-19: The FAA is adopting a new airworthiness directive (AD) for certain SAP cast cylinder assemblies installed in Teledyne Continental Motors (TCM) 470, 520, and 550 series reciprocating engines, Lycoming Engines (LE) 320, 360, and 540 series reciprocating engines, Avco Lycoming (AL) 540 series reciprocating engines, and Superior Air Parts, Inc. (SAP) 360 series reciprocating engines. This AD requires removing from service certain SAP part numbered (P/N) cast cylinder assemblies installed in TCM, LE, and AL reciprocating engines. This AD also requires removing from service certain cast cylinder assemblies installed as original equipment in SAP reciprocating engines, or in certain overhauled or repaired SAP reciprocating engines. This AD results from nine separated SAP cylinder assemblies in TCM reciprocating engines and one in LE reciprocating engines. We are issuing this AD to prevent cylinder separation that can lead to engine failure, a possible engine compartment fire, and damage to the airplane.
2021-11-09: The FAA is adopting a new airworthiness directive (AD) for Airbus Helicopters Deutschland GmbH Model MBB-BK 117 A-1, MBB-BK 117 A- 3, MBB-BK 117 A-4, MBB-BK 117 B-1, MBB-BK 117 B-2, and MBB-BK 117 C-1 helicopters. This AD was prompted by an analysis of the main rotor (M/ R) blade loop area. This AD requires repetitive inspections of certain M/R blade thimble areas and corrective actions if necessary, as specified in a European Aviation Safety Agency (now European Union Aviation Safety Agency) (EASA) AD, which is incorporated by reference (IBR). The FAA is issuing this AD to address the unsafe condition on these products.
2004-23-02: The FAA supersedes Airworthiness Directive (AD) 87-22-01 R1, which applies to certain Raytheon Aircraft Company (Raytheon) 65, 90, 99, 100, 200, and 1900 series airplanes, and Models 70 and 300 airplanes. AD 87-22-01 R1 currently requires you to repetitively inspect the nose landing gear (NLG) fork for cracks. If cracks are found that exceed certain limits, AD 87-22-01 R1 requires you to replace the NLG fork with a serviceable part or an improved NLG fork (Kit No. 101-8030-1 S or Kit No. 114-8015-1 S, as applicable). Incorporating an improved NLG fork kit terminates the repetitive inspection requirements. This AD is the result of FAA's policy (since 1996) to disallow airplane operation when known cracks exist in primary structure. This AD retains the inspection requirements of AD 87-22-01 R1, requires you to incorporate an improved NLG fork kit anytime a crack is found, and adds additional airplanes to the applicability section of this AD. We are issuing this AD to detect andcorrect cracks in the NLG fork, which could result in reduced structural integrity and inability of the NLG fork to carry design limit and ultimate loads. The reduced residual strength may cause separation failure of the NLG fork, which could result in loss of control of the airplane during take off, landing, and taxi operations.
2021-10-25: The FAA is adopting a new airworthiness directive (AD) for certain Airbus Helicopters Model EC130B4 and EC130T2 helicopters. This AD was prompted by a report of cracks and geometrical non-conformities of the tail rotor blades (TRBs); all cracks initiated in the drain hole area at the blade root section. This AD requires cleaning affected parts, visual and dye penetrant inspections for cracks of affected parts, a dimensional inspection to verify conformity of affected parts, and corrective actions if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.