Results
2013-02-09: We are adopting a new airworthiness directive (AD) for all BAE SYSTEMS (OPERATIONS) LIMITED Model BAe 146, and Avro 146-RJ series airplanes. This AD was prompted by a report of loss of the end caps on the anti-icing piccolo tube of the wing leading edge. This AD requires a detailed inspection of the end caps on the anti-icing piccolo tube for lost or loose end caps, and replacing or repairing the end caps if necessary. We are issuing this AD to detect and correct lost and loose end caps on the anti-icing piccolo tube, and ice accretion on the wing leading edge or run-back ice, which could lead to a reduction in the stall margin on approach and loss of controllability of the airplane.
2025-07-06: The FAA is superseding Airworthiness Directive (AD) 2024-26- 01, which applied to all Airbus Helicopters Model H160-B helicopters. AD 2024-26-01 required measuring the axial play of the rotating scissors spherical bearings, and depending on the results, accomplishing corrective action and reporting inspection results. Since the FAA issued AD 2024-26-01, Airbus Helicopters issued revised material to extend the applicability to all rotating scissors spherical bearing serial numbers, change the initial compliance time, establish repetitive inspections, and extend the reporting requirements. This AD was prompted by a determination that the initial compliance time and reporting requirement needed to be modified and repetitive inspections for certain axial play measurements added. This AD retains the actions required in AD 2024-26-01, revises the initial compliance time, extends the definition of an affected part to all serial numbered rotating scissors spherical bearings, extends the reporting requirements, and requires repetitive inspections. This AD also prohibits installing an affected rotating scissors spherical bearing unless certain requirements are met. These actions are specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2013-02-05: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This AD requires, for certain airplanes, installing two warning level indicator lights on each of the P1-3 and P3-1 instrument panels in the flight compartment. This AD also requires, for certain airplanes, replacing the existing P5-16 and P5-10 panels; and, for certain airplanes, replacing the basic P5-16 panel with a high altitude landing P5-16 panel. Additionally, this AD requires revising the airplane flight manual to remove certain requirements of previous AD actions, and to advise the flightcrew of certain changes. This AD was prompted by a design change in the cabin altitude warning system that would address the identified unsafe condition. We are issuing this AD to prevent failure of the flightcrew to recognize and react to a valid cabin altitude warning horn, which could result in incapacitation of the flightcrew due tohypoxia (a lack of oxygen in the body), and consequent loss of control of the airplane.
69-01-01: 69-01-01 FAIRCHILD-HILLER: Amendment 39-703. Applies to F-27 and FH-227 type airplanes. Compliance required within the next 500 hours time in service after the effective date of this AD, unless already accomplished. To preclude the possibility of rendering an engine fire extinguisher system inoperative by a single shorted cartridge unit modify the engine fire extinguisher systems in accordance with Fairchild Hiller Service Bulletins F27-26-5 or FH227-26-3 both dated May 16, 1968, as applicable, or later FAA approved revision, or an equivalent modification approved by the Chief, Engineering and Manufacturing Branch, FAA, Eastern Region. This amendment is effective February 1, 1969.
2012-17-08: We are superseding four airworthiness directives related to the main rotor yoke (yoke) on the Bell Model 204B, 205A, 205A-1, 205B, and 212 helicopters, to retain certain inspections and certain life limits, to require an increased inspection frequency for certain yokes, and to expand these inspections and retirement lives to other yokes. This airworthiness directive is prompted by past reports of cracks in the yoke, another recent report of a cracked yoke, and the decision that other yokes, approved based on identicality, need to be subject to the same inspection requirements and retirement lives. The actions are intended to detect a crack in a yoke to prevent failure of the yoke, and subsequent loss of control of the helicopter.
2025-07-08: The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model AS332C, AS332C1, AS332L, and AS332L1 helicopters. This AD results from a report of the loss of the tail rotor pitch control due to a fracture of the tail rotor slide of the tail rotor head (TRH) assembly. This AD requires inspecting the slide of the control plate of the TRH assembly for any score, scratch, crack, or corrosion, removing corrosion and replacing the TRH assembly, slide of the control plate, or pitch control assembly if discrepancies are found, and reporting the results of the inspection. This AD prohibits installing an affected TRH assembly unless the actions of this AD are accomplished. All of these actions are specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2025-06-51: The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited (Bell) Model 505 helicopters. The FAA previously sent this AD as an emergency AD to all known U.S. owners and operators of these helicopters. This AD was prompted by deformation and/or improper pin engagement in the knuckles of the door hinge on the aft movable ballast box assembly. This AD requires removing all ballast weights from the aft movable ballast box assembly and prohibits the use of ballast weights within the aft movable ballast box assembly, as specified in a Transport Canada emergency AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2003-09-08: This amendment supersedes an existing airworthiness directive (AD), applicable to all Boeing Model 767 series airplanes, that currently requires an inspection to ensure that all bolts of the support beam of the hinge fitting assembly on both the left- and right- hand outboard trailing edge flaps are the correct length and type, and correction of any discrepancy found. This amendment reduces the applicability of the existing AD, adds inspections, and mandates terminating action. The actions specified by this AD are intended to prevent failure of the bolts that attach the outboard trailing edge flap to the support beam, which could result in loss of the flap and consequent reduced controllability of the airplane. This action is intended to address the identified unsafe condition.
47-51-08: 47-51-08 REPUBLIC: Applies to All Model RC-3 Airplanes with Steerable Tailwheels. Compliance required not later than the next 25-hour inspection. To preclude the possibility of the steerable tailwheel control cable fouling on the tailwheel quadrant arms, install horns 3 9/16 inches long, fabricated from 0.091 aluminum plate, pointing rearward to arms of quadrant assembly No. 17F42093-1. Drill out stop rivet and attach using AN 441-4-5 rivets. Then attach cable clips over horn and arm with AN 24-11 bolts. (Republic Service Bulletin No. 17, Supplement No. 2, dated October 16, 1947, also covers this same subject.)
2013-01-02: We are superseding an existing airworthiness directive (AD) for certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes; and certain Model 757-200, -200PF, and -300 series airplanes. That AD currently requires replacing the control switches of the forward, aft, and nose cargo doors of Model 747 airplanes; and requires replacing the control switches of cargo doors 1 and 2 of Model 757 series airplanes. This new AD adds airplanes to the applicability and revises the initial compliance times for those airplanes. This AD was prompted by reports of problems associated with the uncommanded operation of cargo doors. We are issuing this AD to prevent injuries to persons and damage to the airplane and equipment.