Results
65-15-03: 65-15-03 CONSOLIDATED AERONAUTICS: Amdt. 39-103 Part 39 Federal Register July 1, 1965. Applies to Model Lake LA-4 Aircraft. Compliance required within the next 25 hours' time in service after the effective date of this AD unless already accomplished. To prevent failure of the nose landing gear to latch in the down and locked position, accomplish the following: (a) Inspect the bolt at the top of the nose gear drag strut at Fuselage Station 12 5/8 that connects the upper drag strut assembly, Lake P/N 2-4411-1, to the support assembly plates, Lake P/N 2-4412-27, to ensure that an AN5-16A bolt or an FAA-approved equivalent is installed and that the bolt head is on the right-hand side of the aircraft. (b) If an AN5-15A bolt is installed, remove the bolt and visually inspect the bolt hole of the upper drag strut assembly and both support assembly plates for elongation. (c) Rework any part having an elongated bolt hole in accordance with Consolidated Aeronautics, Inc., Lake Aircraft Division, Service Letter No. 11B, dated February 22, 1965, or an equivalent approved by the Chief, Engineering and Manufacturing Branch, FAA Eastern Region, or replace the part with a new part of the same part number or an equivalent approved by the Chief, Engineering and Manufacturing Branch, FAA Eastern Region. (d) Replace any AN5-15A bolt with an AN5-16A bolt or an AN5-17A bolt as necessary when bushings are installed or an FAA-approved equivalent, installing the bolt with the head on the right-hand side of the aircraft. (e) Reverse any AN5-16A bolt that is installed with the head on the left-hand side of the aircraft. This directive effective July 1, 1965.
2021-26-25: The FAA is adopting a new airworthiness directive (AD) for certain Schempp-Hirth Flugzeugbau GmbH Model Duo Discus and Duo Discus T gliders. This AD was prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as jerky extension of the air brakes at very high air speeds, including cases where the air brake blades interlock. This AD requires replacing certain air brake end stop bushings, inspecting certain other air brake end stops, and repairing if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
2022-02-16: The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD was prompted by a determination that radio altimeters cannot be relied upon to perform their intended function if they experience interference from wireless broadband operations in the 3.7-3.98 GHz frequency band (5G C-Band), and a recent determination that, during landings, as a result of this interference, certain airplane systems may not properly transition from AIR to GROUND mode when landing on certain runways, resulting in degraded deceleration performance and longer landing distance than normal due to the effect on thrust reverser deployment, speedbrake deployment, and increased idle thrust. This AD requires revising the limitations and operating procedures sections of the existing airplane flight manual (AFM) to incorporate limitations prohibiting certain landings and the use of certain minimum equipment list (MEL) items, and to incorporate operating procedures for calculating landing distances, when in the presence of 5G C-Band interference as identified by Notices to Air Missions (NOTAMs). The FAA is issuing this AD to address the unsafe condition on these products.
89-14-07: 89-14-07 AEROSPATIALE: Amendment 39-6257. Applicability: Model ATR42-300 series airplanes, Serial Numbers 003 through 052, certificated in any category. Compliance: Required as indicated, unless previously accomplished. To prevent failure of the emergency exit frame, accomplish the following: A. Prior to the accumulation of 12,000 landings or within 60 days after the effective date of this AD, whichever occurs later, accomplish modification of the fuselage emergency exit frame in accordance with Aerospatiale Service Bulletin ATR42-53-0024, Revision 2, dated May 16, 1988. B. An alternate means of compliance or adjustment of the compliance time, which provides an acceptable level of safety, may be used when approved by the Manager, Standardization Branch, ANM-113, FAA, Northwest Mountain Region. NOTE: The request should be forwarded through an FAA Principal Maintenance Inspector (PMI), who will either concur or comment and then send it to the Manager, Standardization Branch, ANM-113. C. Special flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate airplanes to a base in order to comply with the requirements of this AD. All persons affected by this directive who have not already received the appropriate service documents from the manufacturer may obtain copies upon request to Aerospatiale, 316 Route de Bayonne, 31060 Toulouse, Cedex 03, France. These documents may be examined at the FAA, Northwest Mountain Region, Transport Airplane Directorate, 17900 Pacific Highway South, Seattle, Washington, or at the Standardization Branch, 9010 East Marginal Way South, Seattle, Washington. This amendment (39-6257, AD 89-14-07) becomes effective on August 7, 1989.
47-36-02: 47-36-02 DOUGLAS: (Was Mandatory Note 2 of AD-3L-1.) Applies to A-26B and A-26C Aircraft. Compliance required prior to operation in cold weather and not later than next engine overhaul. To preclude collapse of the oil screen during cold weather starting, replace oil screen assembly No. 51887 with oil screen assembly Nos. 51887M or 107547. P/N 51887 may be reworked to P/N 51887M by incorporating reinforcing spring No. 107542 and adding the letter "M" to the part number.
2004-13-17: This amendment supersedes an existing airworthiness directive (AD), applicable to certain Fokker Model F.28 Mark 0070 series airplanes, that currently requires a one-time inspection to detect loose bolts attaching the gustlock counter-bracket to the pulley on the elevator tension regulator (control) assembly, and corrective action if necessary. This AD instead requires a modification of the elevator tension control mechanism. This AD also revises the applicability to include additional airplanes. The actions specified by this AD are intended to prevent restricted elevator movement and consequent reduced controllability of the airplane. This AD is intended to address the identified unsafe condition.
53-10-02: 53-10-02 de HAVILLAND: Applies to Model DHC-2 (Beaver) Aircraft, Serial Numbers 1 to 401 Inclusive. Compliance required as indicated. After the aircraft has acquired 500 hours of flying time and pending the incorporation of the recommended repair, the wings should be inspected for cracks in lower wing skin at ends of the short stringers at the root end station of the wing leading edges at 50-hour intervals. If no cracks are evident reinforcements should be installed on the bottom surface of the wing as a preventive measure. The FAA concurs in this mandatory action by the Canadian Department of Transport. (de Havilland Technical News Sheet Series B, No. 59 - Issue 2 dated January 15, 1953, available from de Havilland Aircraft of Canada, Ltd., Toronto, Ontario, Canada, covers this same subject and describes method of reinforcement.)
2021-26-26: The FAA is superseding Airworthiness Directive (AD) 2005-12-08 for certain Safran Helicopter Engines, S.A. (Safran Helicopter Engines) Arrius 2B1, 2B1A, 2B1A-1, and 2B2 model turboshaft engines. AD 2005-12- 08 required replacing the software in the engine electronic control unit (EECU). This AD was prompted by a report of simultaneous loss of automatic control on both engines installed on an Airbus Helicopters Deutschland (formerly Eurocopter Deutschland) EC135 helicopter during flight. This AD requires replacement of the EECU or upgrade of the EECU software for engines with a certain EECU part number (P/N) installed. This AD also prohibits installation of an affected EECU onto any engine. The FAA is issuing this AD to address the unsafe condition on these products.
2012-12-21: We are superseding an existing airworthiness directive (AD) for all Eurocopter Deutschland GmbH (ECD) Model MBB-BK 117 C-2 helicopters. That AD currently requires revising the ``Emergency and Malfunction Procedures'' and ``Performance Data'' sections of the Rotorcraft Flight Manual (RFM) by inserting three temporary pages into the RFM to alert pilots to monitor the power display when a generator is deactivated and provides procedures to prevent failure of the remaining generator. Before we issued that AD, the manufacturer developed a procedure to modify the two ``After Junction Boxes'' by removing a diode from each box, which provides terminating action for our AD requirements. These actions are intended to require implementing this terminating action to prevent an electrical power system failure and subsequent loss of control of the helicopter and revising the RFM accordingly, by removing the temporary pages inserted to comply with the superseded AD.
95-03-07: This amendment adopts a new airworthiness directive (AD), applicable to certain Aerospatiale Model ATR72 series airplanes, that requires an inspection to determine the model and orientation of certain flight control rods, and replacement of the rods with modified rods, if necessary. This amendment is prompted by reports of corrosion found on the pitch and rudder trim and rudder travel limiter fail-safe rods. The actions specified by this AD are intended to prevent problems associated with corrosion of the flight control rods, which could compromise the required strength of these items.