Results
2014-26-10: We are adopting a new airworthiness directive (AD) for all Airbus Model A318, A319, A320, and A321 series airplanes. This AD was prompted by a determination that the maintenance actions for airplane systems susceptible to aging must be mandated. This AD requires revising the maintenance or inspection program to incorporate more restrictive maintenance requirements and airworthiness limitations. We are issuing this AD to mitigate the risks associated with aging effects of airplane systems. Such aging effects could change the characteristics leading to an increased potential for failure, which could result in failure of certain life-limited parts, and could reduce the structural integrity or reduce controllability of the airplane.
2014-26-07: We are adopting a new airworthiness directive (AD) for all Dassault Aviation Model FAN JET FALCON and FAN JET FALCON SERIES C, D, E, F, and G airplanes. This AD was prompted by our determination of the need for a revision to the airplane airworthiness limitations to introduce changes to the maintenance requirements and airworthiness limitations. This AD requires revising the maintenance or inspection program, as applicable, to incorporate a new airworthiness limitations section. We are issuing this AD to prevent reduced structural integrity of the airplane.
73-06-02: 73-06-02 AERO COMMANDER: Amdt. 39-1606. Applies to all Models 500, 500A, 500B, 500U, 520, 560, 560A, 560E, 560F, 680, 680E, 680F, 680F(P), 680FL, 680FL(P) and 720 series airplanes certificated in all categories. Compliance required within the next 200 hours' time in service after the effective date of this AD, unless already accomplished. To prevent siphoning of fuel from the fuel tanks and thereby contribute to fuel exhaustion with resultant stoppage of both engines, accomplish the following: a. On Models 520 and 560, serial numbers 1 through 230, replace the standard fuel cap assemblies with non-siphoning fuel cap assemblies, Aero Commander Kit No. 87A-1. b. On the following models, replace the standard fuel cap assemblies with non- siphoning fuel cap assemblies, Aero Commander Kit No. 87A-2 (optional fuel caps already installed by use of Aero Commander Kit No. 87 are acceptable): (1) Models 500, 500A, 500B, 500U, 560A, 560E, 560F, 680, 680E, 680F, 680F(P), 680FL(P) and 720, serial numbers 231 through 1854. (2) Model 680FL, serial numbers 1261 through 1738. c. The compliance time for this AD may be adjusted up to a maximum of 50 hours to coincide with the aircraft's annual or 100 hour scheduled inspection. Aero Commander Custom Kit No. 87A contains the hardware and instructions necessary to accomplish this modification. Equivalent replacement parts approved by the Chief, Engineering and Manufacturing Branch, Flight Standards Division, Southwest Region, Federal Aviation Administration, Fort Worth, Texas, may be used. This amendment becomes effective March 19, 1973.
62-26-02: 62-26-02 GRUMMAN: Amdt. 513 Part 507 Federal Register December 6, 1962. Applies to Model G-159 Aircraft Serial Numbers 1 through 93, Except Numbers 75 and 76, and to Aircraft Serial Number 114. Compliance required as indicated. Abnormal fuel system operation has caused structural damage to the wing area of Grumman Model G-159 airplanes. As this condition is likely to exist on other airplanes of the same type design, accomplish the following: (a) Unless already accomplished, the following inspection is required prior to further flight, except that if the airplane is presently located at a base where the equipment and personnel necessary to conduct such an inspection are not available, the airplane may be ferried without passengers to a base where such equipment and personnel are available: (1) Defuel the left and right wing tanks. (2) Remove the inspection covers in the upper surface of the wings between the fuselage and the nacelle and between the nacelle and the fuel filler caps. (3) Inspect for damage to the wing structure in the integral tanks. Pay particular attention to the three top and three bottom rivets in the vertical stiffeners on the ribs. (b) Unless already accomplished, the following repair for damaged aircraft and the following modification for all aircraft are required prior to further flight except that if the damage is confined to the stiffener and rib attachments, the airplane may be operated under a special flight permit (CAR 1.76) to a base where the repair and modification may be made: (1) Repair damage in accordance with Grumman FAA approved instructions or equivalent approved by Chief, Engineering and Manufacturing Branch, FAA Eastern Region, New York International Airport, New York. (2) Modifying by removing the fuel vent flow valve Parker P/N 119-578735 from each tank and drilling a 5/32-inch diameter hole in the valve body in accordance with Grumman Gulfstream Service Change No. 154. After brush-coating the hole with EC-776 or FAA approved equivalent, reinstall the valve. NOTE. - Aircraft Serial Nos. 1, 7, 12, 26 and 91 already incorporate this modification. (Grumman telegram dated November 12, 1962, to all Gulfstream operators and Grumman Service Change No. 154 cover this same subject.) This directive effective upon publication in the Federal Register for all persons except those to whom it was made effective immediately by telegram dated November 15, 1962.
2014-26-09: We are superseding Airworthiness Directive (AD) 2014-03-05, for certain Bombardier, Inc. Model BD-700-1A10 airplanes. AD 2014-03-05 required modification of the air data probes and sensors. This new AD continues to require modification of the air data probes and sensors. This new AD also adds airplanes to the applicability. This AD was prompted by a report that the manufacturer has determined that some completion centers used the heater current/brake temperature monitor unit (HBMU) logic circuit to control the line voltage of the drain mast heaters. We are issuing this AD to detect and correct an unannunciated failure of two pitot static probe heaters, which could affect controllability of the airplane in icing conditions.
2025-04-11: The FAA is adopting a new airworthiness directive (AD) for all Bombardier, Inc., Model BD-700-2A12 airplanes. This AD was prompted by the discovery that a partial loss of thrust after an engine failure during a required navigation performance authorization required (RNP- AR) approach under certain weight, altitude and temperature (WAT) conditions, may lead to a descent below the specified path guidance. This AD requires a revision to the existing airplane flight manual (AFM), to incorporate updated WAT tables for RNP-AR approach operations. The FAA is issuing this AD to address the unsafe condition on these products.
2014-23-01: We are superseding airworthiness directive (AD) 2013-15-09 for all Pratt & Whitney Division (PW) PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 turbofan engine models with certain second-stage high-pressure turbine (HPT) air seals installed. AD 2013- 15-09 required initial and repetitive inspections for cracks in second- stage HPT air seals. This new AD expands the applicability of AD 2013- 15-09 to include additional part numbers (P/Ns), requires removal of the mating hardware if the second-stage HPT air seal is found with a through-crack, and adds a mandatory terminating action. This AD was prompted by reports of cracking in the original location on two additional P/Ns and reports of through-cracks in a new location in the second-stage HPT air seal. We are issuing this AD to prevent failure of the second-stage HPT air seal, which could lead to uncontained engine failure and damage to the airplane.
66-27-03: 66-27-03\tBOEING: Amdt. 39-307 Part 39 Federal Register November 5, 1966. Applies to Models 707 and 720 Series Airplanes Equipped With Nylon Tube Conduit in the Tail Cone. \n\n\tCompliance required as indicated, unless already accomplished. \n\n\tTo prevent fire in the tail cone due to shorted tail navigation light wires, accomplish the following: \n\n\t(a)\tWithin the next 300 hours' time in service after October 12, 1966, unless already accomplished, inspect tail navigation light wiring for frayed or deteriorated wires and inspect protective nylon tube to ensure that it is secured to bulkhead. Replace frayed or deteriorated wires and secure nylon tube to bulkhead as necessary before further flight. \n\n\t(b)\tRepeat the inspection described in (a) every 300 hours' time in service until the following modifications or equivalent modifications approved by the Chief, Aircraft Engineering Division, FAA Western Region are accomplished but not later than 2,250 hours' time in service from theeffective date of this AD\n\n\t\t(1)\tTrim nylon tube flush with bulkhead 65-14660-3 at Fuselage Station 1653; \n\n\t\t(2)\tInstall cover plate and angle fabricated in accordance with Boeing Service Bulletin No. 2395(R-1) or later FAA-approved revision using a clamp and grommet in accordance with that Bulletin; and \n\n\t\t(3)\tReplace all frayed or chafed tail cone light wiring. \n\n\tThis supersedes AD 66-24-02. \n\n\tThis directive effective November 5, 1966.
2025-04-07: The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A330-200, A330-200 Freighter, and A330-300 series airplanes. This AD was prompted by a report of contamination of the advanced pneumatic detector pressure switch of engine pylon fire detectors. This AD requires require replacement of the affected parts and prohibits installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2014-24-05: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-300, 747-400, 747-400D, and 747SR series airplanes. This AD was prompted by a report of a cracked reveal made from a casting found within a group of airplanes that should have machined reveals made only from 6061 aluminum. This AD requires an inspection to determine the material of the number 3 main entry door (MED) corner reveal, repetitive inspections of certain reveals for cracking, and corrective action if necessary. This AD also requires repetitive inspections for cracking of 6061 machined aluminum one-piece corner reveals, and replacement with 6061 machined aluminum two-piece corner reveals if necessary, which terminates certain repetitive inspections. We are issuing this AD to detect and correct fatigue cracking of the lower forward corner reveal of the number 3 MEDs, which could lead to the door escape slide departing the airplane when the door is opened and the slide is deployed, and consequent injuries to passengers and crew using the door escape slide during an emergency evacuation.