Results
95-24-08: This amendment adopts a new airworthiness directive (AD), applicable to certain Airbus Model A320 series airplanes, that requires replacement of the check valves of the thrust reverser with modified valves on certain airplanes and the replacement of the manual control valves of the thrust reverser with modified valves on certain other airplanes. This amendment is prompted by recent engineering analysis, which revealed that, if the non-return valve installed on the hydraulic return line of the thrust reverser were to jam in the closed position, it could cause pressurization of the Hydraulic Control Unit (HCU). The actions specified by this AD are intended to prevent such pressurization of the HCU due to jamming of the non-return valve in the hydraulic return line, and consequent deployment of a thrust reverser during flight; this condition, if not corrected, could adversely affect the controllability of the airplane.
2020-24-04: The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD requires revising the existing airplane flight manual (AFM) to incorporate procedures for conducting an approach with a localizer- based navigation aid, monitoring localizer raw data, calling out any significant deviations, and performing an immediate go around if the airplane has not intercepted the final approach course as shown by the localizer deviation. This AD was prompted by reports that the autopilot flight director system (AFDS) failed to transition to the instrument landing system localizer (LOC) beam after the consistent localizer capture function in the flight control modules initiated a transition to capture LOC during approach. The FAA is issuing this AD to address the unsafe condition on these products.
94-17-09: This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 747-100, -200, -300, and -400 series airplanes, that requires various modifications of certain evacuation ramp/slides. This amendment is prompted by reports of several evacuation ramp/slide malfunctions. The actions specified by this AD are intended to prevent delayed inflation of evacuation ramp/slides, which could delay or impede the evacuation of passengers during an emergency.
2008-11-02 R1: The FAA is revising an existing airworthiness directive (AD), which applies to all Lockheed Model L-1011 series airplanes. That AD currently requires revising the FAA-approved maintenance program by incorporating new airworthiness limitations for fuel tank systems to satisfy Special Federal Aviation Regulation No. 88 requirements. That AD also requires the accomplishment of certain fuel system modifications, the initial inspections of certain repetitive fuel system limitations to phase in those inspections, and repair if necessary. This AD clarifies the intended effect of the AD on spare and on-airplane fuel tank system components. This AD results from a design review of the fuel tank systems. We are issuing this AD to prevent the potential for ignition sources inside fuel tanks caused by latent failures, alterations, repairs, or maintenance actions, which, in combination with flammable fuel vapors, could result in a fuel tank explosion and consequent loss of the airplane.DATES: This AD is effective December 18, 2009. On June 25, 2008 (73 FR 29410, May 21, 2008), the Director of the Federal Register approved the incorporation by reference of a certain publication listed in the AD. We must receive any comments on this AD by January 19, 2010.
2021-01-04: The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 737 series airplanes, excluding Model 737-100, -200, -200C, -300, -400, and -500 series airplanes. This AD was prompted by reports of cracked or completely severed lugs in the upper aft corner stop fitting assembly of the forward entry door. This AD requires an inspection, a measurement, or a records check of that assembly to determine the part number, and replacement if a certain part is found. The FAA is issuing this AD to address the unsafe condition on these products.
2003-25-03: This amendment adopts a new airworthiness directive (AD), applicable to certain Bombardier Model DHC-8-400, -401, and -402 airplanes, that requires a one-time inspection of the forward engine mount assemblies on the left and right engine nacelles for installation of pre-production engine mount assemblies, and follow-on corrective actions if necessary. This action is necessary to prevent failure of the forward engine mount, which could result in reduced structural integrity of the nacelle and engine support structure. This action is intended to address the identified unsafe condition.
95-10-08: This amendment adopts a new airworthiness directive (AD) that is applicable to Bell Helicopter Textron, Inc. (BHTI)-manufactured restricted category Model UH-1A, UH-1B, UH-1E, UH-1F, UH-1H, UH-1L, UH-1P, TH-1F, and TH-1L helicopters. This action requires verification that the tail rotor control system is rigged in accordance with the applicable maintenance manual; a fluorescent penetrant inspection for cracks at the roots of the gear teeth on the pinion and gear of affected 42-degree tail rotor drive gearbox assemblies (42-degree gearboxes), and replacement of the 42-degree gearbox pinion or gear if cracks are found; and, creation of a component history card to track numbers of torque events. A torque event is defined as a takeoff or a lift (internal or external). This amendment is prompted by 14 accidents reported since 1979 in the United States and Canada related to failure of the 42-degree gearbox. The actions specified in this AD are intended to prevent failure of the 42-degree gearbox, loss of tail rotor control, and subsequent loss of control of the helicopter.
94-17-01: This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 747 series airplanes, that requires inspections to detect cracking in the upper row of fasteners in the lower lobe of the fuselage skin lap joints, and repair, if necessary. This amendment is prompted by reports of incidents involving fatigue cracking and corrosion in transport category airplanes that are approaching or have exceeded their design life goal. The actions specified by this AD are intended to prevent separation of the fuselage skin and rapid loss of pressure in the airplane. This AD also relates to the recommendations of the Airworthiness Assurance Working Group assigned to review Model 747 series airplanes, which indicate that, to assure long term continued operational safety, various structural inspections should be accomplished.
95-10-04: This amendment supersedes an existing airworthiness directive (AD), applicable to AlliedSignal Inc. (formerly Textron Lycoming and Avco Lycoming) Model T5313B and T5317 series turboshaft engines, that currently requires initial and repetitive dye penetrant inspections of the centrifugal compressor impeller for cracks, and if necessary, removal from service. This amendment requires the use of a new, more conservative minor cycle counting factors table, introduces a method for prorating past centrifugal compressor impeller usage based on the new cycle counting factors, provides an enhanced centrifugal compressor impeller inspection procedure, and eliminates flyback criteria based on crack size. For those centrifugal compressor impellers that exceed their published life limit, this amendment implements a schedule for safe removal of time- expired parts. This amendment is prompted by a report of an uncontained centrifugal compressor impeller failure and subsequent rotorcraft accident. The actions specified by this AD are intended to prevent centrifugal compressor impeller failure, which can result in an uncontained engine failure, inflight engine shutdown, or damage to the rotorcraft.
2020-25-12: The FAA is adopting a new airworthiness directive (AD) for all Superior Air Parts, Inc. (SAP) Model IO-360-series and O-360-series reciprocating engines and certain Lycoming Engines (Lycoming) Model AEIO-360-, IO-360-, and O-360-series reciprocating engines with a certain SAP crankshaft assembly installed. This SAP crankshaft assembly is installed as original equipment on the affected SAP engines and as a replacement part under parts manufacturer approval (PMA) on the affected Lycoming engines. This AD was prompted by three crankshaft assembly failures that resulted in the loss of engine power and immediate or emergency landings. This AD requires the removal from service of all affected crankshaft assemblies. The FAA is issuing this AD to address the unsafe condition on these products.