Results
76-26-04: 76-26-04 SCOTTISH AVIATION LIMITED: Amendment 39-2793. Applies to Model HP- 137 Mk. 1 Jetstream airplanes, certificated in all categories, except those airplanes which incorporate Scottish Aviation Limited Modification No. 5111. Compliance is required as indicated. To detect cracks in the outer end of each outer wing flap and to prevent possible flap separation from the airplane and possible loss of airplane control, accomplish the following: (a) For airplanes with 500 or more total landings on the effective date of this AD: (1) Comply with paragraph (c) of this AD, before further flight, (except that the airplane may be flown in accordance with FAR Sections 21.197 and 21.199 to a base where the work can be performed, provided that the flaps remain in the fully retracted position for the duration of the flight,) unless already accomplished within the last 50 landings and thereafter continue to comply with paragraph (c) of this AD at intervals not to exceed 50 landings. (2) Comply with paragraph (d) of this AD, within the next 50 landings and thereafter continue to comply with paragraph (d) at intervals not to exceed 500 landings. (b) For airplanes with less than 500 total landings on the effective date of this AD: (1) Comply with paragraph (c) of this AD before the accumulation of 500 landings and thereafter continue to comply with paragraph (c) at intervals not to exceed 50 landings. (2) Comply with paragraph (d) of this AD before the accumulation of 500 landings or within the next 50 landings after the effective date of this AD whichever occurs later, and thereafter continue to comply with paragraph (d) at intervals not to exceed 500 landings. (c) Visually inspect the outer end of each outer wing flap, Part No. 13760B-405 (left) and 13760B-406 (right), for cracks along the lower flange of the end rib and rib doubler using a magnifying glass with at least 5 power in accordance with the instructions contained in Paragraph 3, Part B of Scottish Aviation Limited Service Bulletin No. 9/5, issue 2, dated August 4, 1976, or an FAA-approved equivalent. (d) Inspect the outer end of each outer wing flap, Part No. 13760-B-405 (left) and 13760B-406 (right), for cracks along the lower flange of the end rib and rib doubler using the radiographic technique in accordance with the instructions contained in Paragraph 3, Part C of Scottish Aviation Limited Service Bulletin No. 9/5, issue 2, dated August 4, 1976, or an FAA- approved equivalent. (e) If, during the inspections required by paragraph (c) and (d) of this AD, cracks are found, replace the affected part with a serviceable part of the same part number. NOTE: A "serviceable part" is defined in Note 1, Parts (a) and (b) of Scottish Aviation Limited Service Bulletin, No. 9/5, issue 2, dated August 4, 1976. (f) Compliance with paragraphs (a)(1), (a)(2), (b)(1), and (b)(2) may be discontinued upon the incorporation of Scottish Aviation Limited Modification 5111. This amendment supersedes Amendment 39-2465, (40FR 58129), AD 75-26-16. This amendment becomes effective January 6, 1977.
2012-05-01: We are adopting a new airworthiness directive (AD) for the Eurocopter France (ECF) Model SA-365C, SA-365C1, SA-365C2, SA-365N, SA- 365N1, AS-365N2, AS 365 N3, and SA-366G1 helicopters. This AD was prompted by some reports of deterioration and two reports of failure of Starflex star arm ends. The actions are intended to modify the main rotor frequency adapters to reduce the temperature in the area, to prevent failure of the star arm end, severe vibration, and subsequent loss of control of the helicopter.
2012-05-05: We are adopting a new airworthiness directive (AD) for certain Bombardier, Inc. Model CL-215-1A10, CL-215-6B11 (CL-215T Variant), and CL-215-6B11 (CL-415 Variant) airplanes. This AD was prompted by reports of cracked or broken support bracket assemblies of the emergency water dump pulley. This AD requires inspecting the bracket assembly of the emergency water dump pulley to determine if certain rivets are installed; replacing rivets and installing new stiffeners on the bracket assembly, if necessary; inspecting the stiffeners for the bracket assembly for cracks, deformation, or corrosion, and replacement if necessary; and re-installing the bracket assembly with radius packers. We are issuing this AD to detect and correct failure of the support bracket assembly of the emergency water dump pulley, and in combination with other system failures, such as an engine failure during take off or a pitch control system jam, may result in loss of controllability of the airplane.
95-23-04: This amendment adopts a new airworthiness directive (AD) that is applicable to all British Aerospace Model BAC 1-11 400 series airplanes. This action requires an inspection of the rod ends of the lift dumper to detect drill holes; a dye penetrant inspection to detect any cracking of drilled holes; and replacement of the rod end with an undrilled rod end, if necessary. This amendment is prompted by a report that, during a routine examination of the operating mechanism of the lift dumper, two cracked aft rod ends were found. Investigation revealed that holes had been drilled in the rod ends for grease nipples during manufacturing, and that cracking had developed at the holes. The actions specified in this AD are intended to prevent asymmetric deployment and subsequent lateral control problems due to cracking of either pair of aft rod ends of the operating mechanism of the lift dumper.
2012-04-10: We are adopting a new airworthiness directive (AD) for all Burl A. Rogers (type certificate previously held by William Brad Mitchell and Aeronca, Inc.) Models 15AC and S15AC airplanes. This AD was prompted by reports of intergranular exfoliation and corrosion of the upper and/or lower wing main spar cap angles found on the affected airplanes. This AD requires repetitive inspections of the upper and lower main wing spar cap angles for cracks and/or corrosion and installing inspection access panels. This AD also requires replacing the wing spar cap angles if moderate or severe corrosion is found and applying corrosion inhibitor. We are issuing this AD to correct the unsafe condition on these products.
97-04-18: This amendment adopts a new airworthiness directive (AD), applicable to all Fokker Model F27 Mark 100, 200, 300, 400, 500, 600, and 700 series airplanes, that requires repetitive x-ray inspections to detect cracks in stringers 4 through 7 of the lower skin of the wings, and modification or repair, if necessary. This amendment also requires modification of the stringers of the lower skin of the wings, which terminates the repetitive inspections. This amendment is prompted by reports of fatigue cracking found in stringers 4 through 7 of the lower skin of the wings. The actions specified by this AD are intended to prevent such fatigue cracking, which could result in reduced structural integrity of the wings.
2012-04-13: We are superseding an existing airworthiness directive (AD) for all RR model RB211-524G2-T-19, -524G3-T-19, -524H-T-36, and -524H2- T-19; and RB211-Trent 553-61, 553A2-61, 556-61, 556A2-61, 556B-61 556B2-61, 560-61, 560A2-61; RB211-Trent 768-60, 772-60, 772B-60; and RB211-Trent 875-17, 877-17, 884-17, 884B-17, 892-17, 892B-17, and 895- 17 turbofan engines that have a high-pressure (HP) compressor stage 1 to 4 rotor disc with a part number (P/N) listed in Table 1 of the AD. That AD currently requires repetitive inspections of the axial dovetail slots, and follow-on corrective action depending on findings. Since we issued that AD, we determined that the definition of shop visit is too restrictive in the existing AD. This continues to require those repetitive inspections and follow-on corrective actions. This new AD changes the definition of a shop visit to be less restrictive. This AD was prompted by our determination that the definition of ``shop visit'' in the existing AD is too restrictive, in that it would require operators to inspect more often than required to ensure safety. We are issuing this AD to detect cracks in the HP compressor stage 1 and 2 disc posts, which could result in failure of the disc post and HP compressor blades, release of uncontained engine debris, and damage to the airplane.
91-24-05: 91-24-05 MCDONNELL DOUGLAS: Amendment 39-8091. Docket No. 91-NM-30-AD. Supersedes AD 90-15-02, Amendment 39-6651. \n\n\tApplicability: All Model DC-9 and DC-9-80 series airplanes, Model MD-88 airplanes, and C-9 (military) airplanes, certified in any category. \n\n\tCompliance: Required as indicated, unless previously accomplished. \n\n\tTo prevent the lap belt connector or buckle from jamming the passenger entrance door hinge, accomplish the following: \n\n\t(a)\tFor airplanes listed in McDonnell Douglas DC-9 Alert Service Bulletin A25-311, dated January 31, 1990: Within six months after August 14, 1990 (the effective date of AD 90-15-02, Amendment 39-6651), modify the forward cabin attendant dual seat, outboard position, lap belt restraint system, in accordance with the Accomplishment Instructions, Paragraph 2, of McDonnell Douglas DC-9 Alert Service Bulletin A25-311, dated January 31, 1990. \n\n\t(b)\tFor airplanes not listed in McDonnell Douglas DC-9 Alert Service Bulletin A25-311, dated January 31, 1990, and having dual forward cabin attendant seats incorporating a restraint system with lap belts independent of the shoulder harness: Within six months after the effective date of this AD, inspect the outboard attendant seat lap belt to determine if the connector or buckle is capable of reaching and interfering with the lower hinge of the passenger entrance door and obstructing the opening of the door. \n\n\t\t(1)\tIf opening of the passenger door entrance is obstructed, prior to further flight, modify the installation so that a shorter lap belt half is utilized, in a manner approved by the Manager, Los Angeles Aircraft Certification Office (ACO), FAA, Transport Airplane Directorate. \n\n\t\t(2)\tIf opening of the passenger entrance door is not obstructed, no further action is necessary. \n\n\t(c)\tAn alternate method of compliance or adjustment of the compliance time, which provides an acceptable level of safety, may be used when approved by the Manager, Los Angeles Aircraft Certification Office (ACO), FAA, Transport Airplane Directorate. \n\n\tNOTE: This result should be forwarded through an FAA Principal Maintenance Inspector, who may concur or comment and then send it to the Manager, Los Angeles ACO. \n\n\tNOTE: Any previously-approved alternative method of compliance with AD 90-15-02 is considered to be an approved alternative method of compliance with this AD. \n\n\tNOTE: The procedures described in McDonnell Douglas DC-9 Alert Service Bulletin A25-321, dated August 8, 1991, are considered an approved alternative method of compliance with paragraph (b) of this AD. \n\n\t(d)\tSpecial flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate airplanes to a base in order to comply with the requirements of this AD. \n\n\t(e)\tThe modification requirements of paragraph (a) of this AD shall be done in accordance with McDonnell Douglas DC-9 Alert Service Bulletin A25-311, dated January 31, 1990. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR Part 51. Copies may be obtained from McDonnell Douglas Corporation, Post Office Box 1771, Long Beach, California 90801; Attn: Business Unit Manager, Technical Publications & Technical Administrative Support, C1-L5B (54-60). Copies may be inspected at the FAA, Transport Airplane Directorate, 1601 Lind Avenue S.W., Renton, Washington; or at the Los Angeles Aircraft Certification Office, 3229 East Spring Street, Long Beach, California; or at the Office of the Federal Register, 1100 L Street N.W., Room 8401, Washington, D.C. \n\n\tAirworthiness Directive 91-24-05 supersedes AD 90-15-02, Amendment 39-6651. \n\n\tThis amendment (39-8091, AD 91-24-05) becomes effective on January 7, 1992.
2012-04-09: We are adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747SR, and 747SP series airplanes. This AD requires inspections for scribe lines in affected lap and butt splices, wing-to-body fairing locations, and external repair and cutout reinforcement areas; and related investigative and corrective actions if necessary. This AD was prompted by reports of scribe lines found at lap joints and butt joints, around external doublers and antennas, and at locations where external decals had been cut. We are issuing this AD to detect and correct scribe lines, which can develop into fatigue cracks in the skin and cause sudden decompression of the airplane.
98-18-13: This amendment adopts a new airworthiness directive (AD) that applies to certain SOCATA-Groupe AEROSPATIALE (Socata) Models TB20 and TB21 airplanes. This AD requires repetitively inspecting the main landing gear (MLG) attachment bearing (using a dye penetrant method) for cracks, and if cracks are found, replacing the bearing. This AD is the result of mandatory continuing airworthiness information (MCAI) issued by the airworthiness authority for France. The actions specified by this AD are intended to detect and correct cracks in the MLG attachment bearing, which could result in collapse of the main landing gear during taxi and landing operations.