|
2004-13-03: The FAA is adopting a new airworthiness directive (AD) for Rolls-Royce (1971) Limited, Bristol Engine Division (RR) Model Viper Mk.601-22 turbojet engines. This AD requires reducing the life of certain 1st stage turbine rotor blades from 7,000 hours time-in-service (TIS) to 4,600 hours TIS, and provides a drawdown schedule for blades that have already exceeded the new reduced life limit. This AD results from the manufacturer's investigations into failures of 1st stage turbine rotor blades. We are issuing this AD to prevent multiple failures of 1st stage turbine rotor blades that could result in a dual-engine shutdown.
|
|
48-45-01: 48-45-01 FAIRCHILD: Applies to All M-62 Series Aircraft.
Compliance required at each annual inspection.
(1) Inspect plywood butt plates for separation from wing spar ends. Remove only if loose and inspect spar end for rot which requires repair or replacement. Separation of spar laminations does not require replacement if the glue joints between spar webs and caps are sound. Glue new butt plates to spar ends working glue into any cracks between laminations.
(2) Cut a total of sixteen 1/2-inch diameter inspection holes in wing lower skin. These should be centered at the front edges of both spars at four approximately equally spaced sparwise stations in each outer panel. Use caution to avoid cutting the spars and ribs. Inspect spars for rot and separation of the plywood webs from the caps. Deteriorated parts should be scrapped or repaired. Dope fabric patches over holes.
(3) Provides 1/4-inch drain holes in lower skin with centers not more than 1/4 inch from front face of spars and from outer edge of each rib wherever holes are missing or have greater spacing. Clean out all dirt built up above edges of holes to insure complete drainage. Install seaplane grommets at all drain holes in areas splashed by water from landing wheels.
This supersedes AD 48-07-04.
|
|
2021-05-03: The FAA is adopting a new airworthiness directive (AD) for certain Airbus Helicopters Model EC225LP helicopters. This AD requires various inspections of the left-hand side (LH) engine fuel supply (fuel supply) hose and depending on the inspection results, reinstalling the fuel supply hose or removing the fuel supply hose from service. Additionally, this AD requires installing an improved part and prohibits installing a certain part-numbered LH fuel supply hose on any helicopter unless it is installed by following certain procedures. This AD was prompted by a report of an incorrect installation of the LH fuel supply hose causing restricted fuel flow to the LH engine. The FAA is issuing this AD to address the unsafe condition on these products.
|
|
2004-12-19: This amendment adopts a new airworthiness directive (AD), applicable to certain Airbus Model A319, A320, and A321 series airplanes. This AD requires replacement of a certain transformer rectifier unit (TRU) with a certain new TRU. This action is necessary to prevent ignition of the input filter capacitors of the TRU in position 2 of the avionics compartment, which could potentially result in smoke in the cockpit. This action is intended to address the identified unsafe condition.
|
|
48-07-01: 48-07-01 CESSNA: Applies to 120 and 140 Aircraft Serial Numbers 8001 Through 14329.
Compliance required by May 1, 1948, and at each annual inspection thereafter.
Inspect the two bolts attaching the horizontal stabilizer to the fin post for tightness and proper length. If no bolt threads extend through the fiber lock rings of the anchor nuts inside the stabilizer attachment fitting, or if the bolts show any indication of having backed off when checked with a wrench, they should be replaced with AN 4-5A bolts on Serial Nos. 10091 and up, or AN 3-5A bolts on earlier serial numbers. In making the tightness check use caution to avoid stripping the threads in the anchor nut. If the new bolts do not develop at least 3 inch- pounds torque in the anchor nut, AN 4-H5A or AN 3-H5A (drilled head) bolts should be substituted and safetied together with wire. Check the clearance of the elevator horn and horn bolts with respect to the cutouts in the fin spar and increase it to a minimum of 1/8 inch wherever necessary.
(Cessna Service Letter No. 52 covers this same subject.)
|
|
47-41-02: 47-41-02 BELL: (Was Mandatory Note 14 of AD-1H-2.) Applies to Models 47B and 47B3 Helicopters.
Compliance required prior to next flight after receipts of parts from Bell Aircraft Corp., but, in any event, not later than January 1, 1948.
To prevent excessive vibration and subsequent failure of the main oil line from the oil cooler to the oil filter, two additional supports must be installed for this oil line, one each at the bends near the oil filter and oil cooler.
(Bell Service Bulletin 47C28 (revised), dated July 1, 1947, covers this same subject.)
|
|
2012-13-01: We are adopting a new airworthiness directive (AD) for all Saab AB, Saab Aerosystems Model 340A (SAAB/SF340A) and SAAB 340B airplanes. This AD was prompted by reports indicating that wear of the elevator pushrods has occurred on some airplanes after extended time in service. This AD requires determining if a certain part number is installed, performing a detailed inspection for individual play between the elevator pushrod assembly and degradation of elevator pushrod assembly, and replacing the affected elevator pushrod assembly with a new elevator pushrod assembly if necessary. We are issuing this AD to prevent a free elevator from affecting the pitch control authority, which may result in reduced controllability of the airplane.
|
|
2004-12-17: This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 757-200 series airplanes, that requires repetitive inspections of the intercostals that back up the door stops and hinges at door 2 left and door 2 right for cracks, and corrective action, if necessary. This amendment also provides for an optional terminating action for the repetitive inspections. This action is necessary to prevent fatigue cracks from propagating in the intercostals, which could lead to the loss of a door in flight and subsequent rapid decompression. This action is intended to address the identified unsafe condition.
|
|
47-21-19: 47-21-19 REPUBLIC: (Was Mandatory Note 9 of AD-769-2.) Applies to Model RC-3 Aircraft Serial Numbers 5 to 238, Inclusive.
Compliance required not later than the next 25 hours of operation subsequent to July 1, 1947, but in no case later than September 1, 1947.
Inspect parking brake, battery, mixture and carburetor heat flexible controls for presence of brass ferrule or AN 742D3 clamp on split sleeve at operating end of these controls. If clamp or ferrule is not installed, split metal sleeve can open permitting casing to slide out when control is actuated thus rendering the control ineffective. The above clamp should be installed immediately.
(Seabee Service News No. 10, dated January 13, 1947, covers this subject.)
|
|
2012-11-13: We are adopting a new airworthiness directive (AD) for the Aeronautical Accessories, Inc. (AAI), High Landing Gear Aft Crosstube Assembly (aft crosstube) installed on certain Bell Helicopter Textron, Inc. (Bell) and Agusta S.p.A. (Agusta) model helicopters as an approved Bell part installed during production or based on a Supplemental Type Certificate (STC). This AD requires certain recurring visual, dimensional, and fluorescent penetrant inspections of each aft crosstube, and replacing any cracked crosstube. This AD also requires establishing a life limit and creating a component history card or equivalent record for one of the affected part-numbered aft crosstubes. This AD was prompted by three reports of failed crosstubes because of cracks. The actions are intended to prevent failure of a crosstube, collapse of the landing gear, and subsequent loss of control of the helicopter.
|