Results
2020-18-07: The FAA is superseding Airworthiness Directive (AD) 2016-18- 09, which applied to certain Airbus SAS Model A318, A319, and A320 series airplanes. AD 2016-18-09 required repetitive detailed inspections for damage on the fuselage skin at certain frames, and applicable related investigative and corrective actions. This AD continues to require repetitive inspections of the fuselage skin for chafing damage at certain frames using a new inspection process, and corrective actions if necessary; as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. This AD was prompted by reports of additional chafing of the forward fuselage found underneath the fairing structure. Investigation revealed the cause as contact between the belly fairing nut plate and the fuselage. The FAA is issuing this AD to address the unsafe condition on these products.
2008-11-05: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: Based on some recent in-service findings for fluid ingress and/ or inner skin disbond damage on rudders, AIRBUS decided to introduce some further structural inspections to specific rudder areas. This type of damage could result in reduced structural integrity of the rudder. * * * * * We are issuing this AD to require actions to correct the unsafe condition on these products.
2001-17-30: This amendment adopts a new airworthiness directive (AD), that is applicable to Pratt & Whitney JT9D-7R4 series turbofan engines. This amendment requires initial and repetitive fluorescent penetrant inspection (FPI) of the high pressure turbine (HPT) 1st stage disk aft lugs, and if the aft lug(s) are cracked, replacement of the HPT 1st stage disk and HPT 1st stage airseals. Also, for certain configuration HPT disk assemblies, this amendment requires replacement of the HPT 1st stage airseals with newly designed airseals at the next accessibility. This amendment is prompted by reports of cracks in HPT 1st stage disk firtrees and failure of firtree lugs. The actions specified by this AD are intended to prevent 1st stage HPT disk firtree fracture, which could result in an uncontained engine failure, and damage to the airplane.
2020-17-14: The FAA is adopting a new airworthiness directive (AD) for all Dassault Aviation Model Falcon 10 airplanes. This AD was prompted by a report of hydraulic fluid on the ground near the main landing gear (MLG) brake assembly. The hydraulic leakage started in a cracked hydraulic pipe, with the crack likely due to chafing between two \n\n((Page 54889)) \n\nhydraulic pipes or between hydraulic pipes and structure. This AD requires an inspection for chafing or interference of certain hydraulic pipes and certain rib passage holes, and, depending on findings, modification or repair, as specified in a European Union Aviation Safety Agency (EASA), which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
2005-05-02: The FAA is adopting a new airworthiness directive (AD) for all McDonnell Douglas Model MD-90-30 airplanes. This AD requires a general visual inspection in the electrical/electronics (E/E) compartment for damage of the wire bundle and aft right radio rack structure at station 160.000, and corrective actions if necessary. This AD also requires modifying the radio rack structure and wire bundle routing. This AD is prompted by a report indicating that burnt wiring was discovered in the wire bundle at station 160.000 in the E/E compartment. We are issuing this AD to detect and correct chafing of the wire bundle at station 160.000 against the support bracket located on the aft right radio rack, which could lead to shorted or burnt wires and consequent smoke and fire in the E/E compartment.
2008-11-03: We are adopting a new airworthiness directive (AD) for all Boeing Model 737-100, -200, and -200C series airplanes. This AD requires revising the FAA-approved maintenance inspection program to include inspections that will give no less than the required damage tolerance rating for each structural significant item (SSI), doing repetitive inspections to detect cracks of all SSIs, and repairing cracked structure. This AD results from a report of incidents involving fatigue cracking in transport category airplanes that are approaching or have exceeded their design service objective. We are issuing this AD to maintain the continued structural integrity of the entire fleet of Model 737-100, -200, and -200C series airplanes. \n\nDATES: This AD is effective June 25, 2008. \n\n\tThe Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of June 25, 2008. \n\n\tThe Director of the Federal Register approved the incorporation byreference of Boeing Document D6-37089, "Supplemental Structural Inspection Document for Model 737-100/200/200C Airplanes," Revision E, dated May 2007, as listed in this AD, on May 27, 2008 (73 FR 21237, April 21, 2008).
2005-04-15: The FAA is adopting a new airworthiness directive (AD) for certain Dassault Model Falcon 2000EX and 900EX series airplanes. This AD requires prohibiting dispatch with certain equipment inoperative; and revising the airplane flight manual to facilitate recovery of the cockpit display units in the event of an avionics standard communication bus (ASCB) failure and to inform the flightcrew what equipment is inoperative during an ASCB failure. This AD also requires doing an integrity check of the ASCB for any faults and corrective action if necessary, and installing an avionics software update to the Honeywell Primus Epic system. This AD is prompted by a report that an analysis and tests of the Honeywell Primus Epic systems installed on the Model Falcon 2000EX and 900EX series airplanes revealed that all information displayed on the cockpit display units could become invalid during flight. We are issuing this AD to prevent a loss of data from all four of the cockpit display units,and loss of all radio communications (with the exception of VHF emergency frequency and last frequency used), primary navigation instruments, autopilot, auto- throttle, central alerting system, aural alarms, and normal braking (on Model Falcon 2000EX series airplanes only). These losses could reduce the flightcrew's situational awareness, increase flightcrew workload, and consequently reduce the ability to maintain safe flight and landing of the airplane.
2001-17-33: This amendment adopts a new airworthiness directive (AD) for Agusta Model AB412 helicopters. This action prohibits use of the hoist until certain modifications are accomplished. This amendment is prompted by the loss of a hoist hook during flight due to an uncommanded firing of the cable cutter cartridge caused by wire chafing. The actions specified in this AD are intended to prevent wire chafing, inadvertent firing of the cable cutter cartridge, loss of a hoist hook and section of cable, impact with the main or tail rotor, and subsequent loss of control of the helicopter.
2001-17-32: This amendment supersedes an existing airworthiness directive (AD) that applies to Eurocopter France (ECF) Model AS350B, B1, B2, B3, BA, D, AS355E, F, F1, F2, and N helicopters. That AD requires inspecting certain versions of the tail rotor pitch change spider assembly (spider assembly) for the proper rotational torque, axial play, and any brinelling of the bearing. This AD requires identifying the spider assembly with index marks to detect bearing spacer rotation, visually checking to ensure that the index marks are aligned before the first flight of each day, and subsequently modifying the spider assembly. This AD also adds the ECF Model AS350D1 helicopters to the applicability. This AD is prompted by operator reports that the spider assembly bearing spacers are rotating. The actions specified by this AD are intended to detect rotation of the spider assembly bearing spacers, prevent seizure of the bearing, loss of tail rotor control, and subsequent loss of control of the helicopter.
2008-10-15: We are adopting a new airworthiness directive (AD) for certain Boeing Model 747-100, 747-100B, 747-200B, 747-200C, 747-200F, 747-300, 747SR, and 747SP series airplanes. This AD requires an inspection to determine if acceptable external skin doublers are installed at the stringer 6 (S-6) lap splices, between station (STA) 340 and STA 400. For airplanes without the acceptable external skin doublers, this AD requires repetitive related investigative actions and corrective actions if necessary. This AD also provides an optional terminating modification for the repetitive related investigative actions. This AD results from a report of cracked fastener holes at the right S-6 lap splice between STA 340 and STA 380. We are issuing this AD to detect and correct cracking in the fuselage skin, which could result in rapid decompression and loss of structural integrity.