Results
2006-26-08: The FAA is adopting a new airworthiness directive (AD) to supersede AD 2006-02-51, which applies to certain Raytheon Aircraft Company Model 390 airplanes. AD 2006-02-51 currently requires you to inspect the left engine hydraulic pump outlet tube and the clamp; replace the clamp at each inspection; replace the hydraulic pump outlet tube immediately if any problem is found; and report the results of each inspection or replacement to the FAA. This AD is the result of several hydraulic pump outlet tube failures after issuance of AD 2006- 02-51, including failures on the right engine. This AD requires you to visually inspect the hydraulic pump outlet tube on both engines on a recurring basis and immediately replace the tube if damage is found. This AD also requires incorporation of an Airplane Flight Manual (AFM) change to not allow operation of an engine with its associated firewall hydraulic shutoff valve closed. In addition, this AD requires you to replace the hydraulic pump outlet tube if an engine is operated with its firewall hydraulic shutoff valve closed. We are issuing this AD to prevent failure of the hydraulic pump outlet tube and consequent leaking of hydraulic fluid. Such leakage could result in a fire. There is also a risk of loss of hydraulic system functions including normal gear extensions, speed brakes, roll spoilers, lift dump, and normal brakes. DATES: This AD becomes effective on December 28, 2006. The Director of the Federal Register previously approved the incorporation by reference of the documents listed in this AD on February 2, 2006 (71 FR 5581, February 2, 2006). We must receive any comments on this AD by February 26, 2007.
87-03-04: 87-03-04 CASA: Amendment 39-5515. Applies to CASA Model C-212 series airplanes listed in CASA Service Bulletins 212-27-30 and 212-27-31, both dated October 23, 1985, certificated in any category. Compliance is required within 8 months after the effective date of this AD. To reduce the potential for a mis-trimmed takeoff, accomplish the following, unless previously accomplished: A. Replace the trim control markings and placards in accordance with CASA Service Bulletins 212-27-30 (CC series airplanes) or 212-27-31 (CB series airplanes), both dated October 23, 1985, as applicable. B. An alternate means of compliance or adjustment of the compliance time, which provides an acceptable level of safety, may be used when approved by the Manager, Standardization Branch, ANM-113, FAA, Northwest Mountain Region. C. Special flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate airplanes to a base for the accomplishment of the modifications required bythis AD. All persons affected by this directive who have not already received the appropriate service document from the manufacturer may obtain copies upon request to Construcciones Aeronauticas S.A., Getafe, Madrid Spain. This document may be examined at the FAA, Northwest Mountain Region, 17900 Pacific Highway South, Seattle, Washington, or the Seattle Aircraft Certification Office, 9010 East Marginal Way South, Seattle, Washington. This amendment becomes effective February 19, 1987.
2006-26-02: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: a leaking brass fuel connection (part no. 10AB-75) was found during maintenance check. This AD requires actions that are intended to address the unsafe condition described in the MCAI.
2018-22-03: We are superseding Airworthiness Directive (AD) 2016-24-03, which applied to certain Bombardier, Inc., Model DHC-8-400 series airplanes. AD 2016-24-03 required repetitive detailed inspections of barrel nuts and cradles, a check of the bolt torque of the preload indicating (PLI) washers, and corrective actions if necessary. This AD retains the requirements of AD 2016-24-03 and requires modifying the airplane by installing a sealing disk to a certain location and replacing certain barrel nuts. This AD was prompted by reports of cracked and corroded barrel nuts found at the mid-spar location of the horizontal-stabilizer-to-vertical-stabilizer attachment joint, and the issuance of new service information that includes a terminal modification. We are issuing this AD to address the unsafe condition on these products.
2006-26-01: The FAA is adopting a new airworthiness directive (AD) for certain CFM International CFM56 Series turbofan engines. This AD requires replacing certain fuel filters manufactured under parts manufacturer approvals (PMA). This AD results from 12 reports of failed fuel filters. We are issuing this AD to prevent the loss of engine thrust that could result in loss of control during takeoff or landing.
85-23-06: 85-23-06 CESSNA: Amendment 39-5225. Applies to Model T303 (Serial Numbers T30300001 thru T30300315) airplanes certificated in any category. Compliance: Required within the next 10 hours time-in-service from the effective date of this AD, unless already accomplished. To preclude the possibility of the fuel metering unit tee fittings from leaking and causing a fire, accomplish the following: (a) Remove both engine cowlings to the extent required to adequately examine the turbocharger inlet area and fuel metering units. Visually inspect the turbocharger inlet and surrounding area for evidence of significant damage caused by exhaust gas leakage. If noted, prior to further flight, repair the damage and eliminate the cause of the leak. (b) With the aircraft auxiliary fuel pumps on and the mixture control in the idle cutoff position, visually inspect the fuel metering unit tee fitting for cracking and leakage in the threaded area that goes into the fuel metering unit. If a crack and resultant leak is detected, prior to further flight replace the fitting, using a wrench on the fitting, to isolate the effects of attaching and tightening the fuel lines. Do not over torque the fitting when installing it on the metering unit. (c) The aircraft may be flown in accordance with FAR 21.197 to a location where this AD can be accomplished. (d) Within five (5) days of accomplishing this AD, report, in writing, all defects found during accomplishment of this AD to the Manager, Wichita Aircraft Certification Office, 1801 Airport Road, Room 100, Mid-Continent Airport, Wichita, Kansas 67209. (Reporting approved by the Offices of Management and Budget under OMB No. 2120-0056.) (e) An equivalent method of compliance may be used when approved by the Manager, Wichita Aircraft Certification Office, Federal Aviation Administration, Central Region, 1801 Airport Road, Room 100, Mid-Continent Airport, Wichita, Kansas 67209. This amendment becomes effective on February 5, 1986, to all persons except those persons to whom it has already been made effective by priority letter from the FAA dated November 14, 1985, and is identified as AD 85-23-06.
2006-25-17: The FAA is adopting a new airworthiness directive (AD) for certain Bombardier Model DHC-8-400 series airplanes. This AD requires repetitive cleaning/inspecting of the drain hole of each pitot static probe and repetitive cleaning of the pitot lines in the pitot static system. This AD results from reports of incidents of airspeed mismatch between the pilot, co-pilot, and standby airspeed indications caused by contamination in the pitot static system. We are issuing this AD to prevent erroneous/misleading altitude and airspeed information from a contaminated pitot static system to the flightcrew, which could reduce the ability of the flightcrew to maintain the safe flight and landing of the airplane.
2021-14-13: The FAA is adopting a new airworthiness directive (AD) for all Pratt & Whitney (PW) PW2037, PW2037M, PW2040, and F117-PW-100 model turbofan engines. This AD was prompted by a report of an uncontained engine failure resulting from cracks in the knife edge of the high- pressure turbine (HPT) 2nd-stage air seal assembly. This AD requires fluorescent penetrant inspections (FPIs) and visual inspections of the HPT 2nd-stage air seal assembly and, depending on the results of the inspections, replacement of the HPT 2nd-stage air seal assembly with a part eligible for installation. This AD also requires replacement of the affected HPT 2nd-stage air seal assembly, depending on the engine model, at either the next engine shop visit or the next piece-part opportunity. The FAA is issuing this AD to address the unsafe condition on these products.
89-10-02: 89-10-02 AEROSPATIALE: Amendment 39-6201. Applicability: Model ATR42-300 series airplanes up to and including serial number 120, which have not been modified in accordance with Service Bulletin ATR42-28-0013, Revision 2, dated January 6, 1989, certificated in any category. Compliance: Required as indicated, unless previously accomplished. To prevent a fuel fire in the nacelle, accomplish the following: A. Within 300 flight hours after the effective date of this AD and thereafter at intervals not to exceed 300 flight hours, and at each engine removal/installation, inspect the engine fuel supply hoses for fuel leakage in accordance with Aerospatiale Service Bulletin ATR42-28-0012, dated September 9, 1988. If leakage is found, before further flight, repair or replace the leaking fuel line, in accordance with the service bulletin. B. Replacement of the engine fuel supply hoses in accordance with Aerospatiale Service Bulletin ATR42-28-0013, Revision 2, datedJanuary 6, 1989, constitutes terminating action for the repetitive inspections required by paragraph A., above. C. An alternate means of compliance or adjustment of the compliance time, which provides an acceptable level of safety, may be used when approved by the Manager, Standardization Branch, ANM-113, FAA, Northwest Mountain Region. NOTE: The request should be forwarded through an FAA Principal Maintenance Inspector (PMI), who may add any comments and then send it to the Manager, Standardization Branch, ANM-113. D. Special flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate airplanes to a base for the accomplishment of inspections and/or modification required by this AD. All persons affected by this directive who have not already received the appropriate service documents from the manufacturer may obtain copies upon request to Aerospatiale, 316 Route de Bayonne, 31060 Toulouse, Cedex 03, France. These documents may be examined atthe FAA, Northwest Mountain Region, 17900 Pacific Highway South, Seattle, Washington, or at the Seattle Aircraft Certification Office, 9010 East Marginal Way South, Seattle, Washington. This amendment (39-6201, AD 89-10-02) becomes effective on May 29, 1989.
86-17-09: 86-17-09 BELL HELICOPTER TEXTRON, INC.: Letter issued August 21, 1986. Applies to all Bell Helicopter Model 212 helicopters, S/N 30501 through 30999, 31101 through 31273, and 31275; 32101 through 32142 and 32201 through 32262 that have T/R hub and blade assembly, P/N 212-011-701-001 installed, certified in any category. Compliance required as indicated unless already accomplished. To prevent failure of the tail rotor control, accomplish the following: (a) Within 25 hours' time in service after receipt of this AD, visually inspect the T/R hub assembly P/N 212-011-701-3, in accordance with Part 1 of Bell Helicopter Textron, Inc. (BHTI), Alert Service Bulletin (ASB) 212-86-39, Revision "A," dated July 23, 1986. (1) If the (P/N) 212-011-716-1 T/R trunnion housing is cracked or there is axial play in the T/R trunnion, or if there are excess balance washers, comply with Part II of the Alert Service Bulletin before further flight. (2) Repeat this inspection every 25 hours' time in service until paragraph (b) of this AD is accomplished. (b) Remove the 212-011-701-1 T/R hub and blade assembly and inspect the trunnion bearing housing, P/N 212-011-716-1, as detailed in Part II of BHTI ASB 212-86-39, Revision "A", dated July 23, 1986, within 150 hours' time in service or within 60 days after the issue date of this AD, whichever occurs first. Replace any housing having an end web thickness of .059 inch or less with a serviceable part. An alternate method of compliance or adjustment of the compliance time, which provides an equivalent level of safety, may be approved by the Manager, Helicopter Certification Branch, Aircraft Certification Division, FAA, Southwest Region. This airworthiness directive becomes effective upon receipt.