Aircraft-logs.com

Results
2010-13-11: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: Due to their position on the aeroplane, fuel fire shut-off valve actuators P/N [part number] 9409122 are susceptible to freezing, which has an adverse effect on the operation of the valve. Also, due to various causes, the failure rate of [fuel fire shut-off valve] actuator P/N 9409122 is higher than expected. Failure or freezing of the actuator may prevent the flight crew to close the fuel fire shut-off valve in case of an engine fire. * * * * * Due to their position on the aeroplane, fuel crossfeed valve actuators P/N 9409122 are susceptible to freezing, which has an adverse effect on the operation of the valve. This condition, if not corrected, maygenerate fuel asymmetry alerts when a valve remains in the open position after being selected closed. It may also prevent the flight crew from correcting a fuel asymmetry when a valve remains in the closed position after being selected open. One event was reported where, due to such problems, the flight crew shut down an engine in-flight and diverted the aircraft. * * * * * * * * [D]ue to their position on the aircraft, ice may form on actuators P/N 9409122 installed on fuel crossfeed valves and fuel fire shut-off valves. Tests revealed that the ice can prevent the actuator and thus the valve from operating in flight (frozen stuck). * * * * * * * * We are issuing this AD to require actions to correct the unsafe condition on these products.
95-26-03: This amendment supersedes an existing airworthiness directive (AD), applicable to Pratt & Whitney (PW) JT8D series turbofan engines, that currently requires inspection, and replacement, if necessary, of suspect 7th through 12th stage high pressure compressor (HPC) disks. This amendment adds 46 more applicable engines, revises the inspection requirements, incorporates a new PW Alert Service Bulletin (ASB), and requires reporting the results of the inspection to the manufacturer. This amendment is prompted by the identification of additional suspect engines, by the development of revised inspection intervals, and by the issuance of the new PW ASB. The actions specified by this AD are intended to prevent an uncontained HPC disk failure, which can result in damage to the aircraft.
2010-13-09: The FAA is adopting a new airworthiness directive (AD) for CFM International, S.A. CFM56-5, -5B, and -7B series turbofan engines. This AD requires removing from service, nine stage 3 low-pressure turbine (LPT) disks, identified by serial number (S/N). This AD results from the discovery of a material nonconformity requiring removal of the disk before the certified disk life of certain stage 3 LPT disks. We are issuing this AD to prevent uncontained failure of the stage 3 LPT disk and damage to the airplane.
2010-12-07: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: Reassessment of the damage tolerance analysis resulted in threshold reduction for some Structure Significant Items (SSI) of the Maintenance Review Board Report (MRBR) Airworthiness Limitations Items (ALI). Failure to inspect these structural components, according to the new threshold, could prevent a timely detection of fatigue cracking. These cracks, if not properly addressed, could adversely affect the structural integrity of the airplane. * * * * * We are issuing this AD to require actions to correct the unsafe condition on these products.
2010-12-02: We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: The installation of TU250 comparator/selector (CS) boards, however, has resulted in a few occurrences of erratic engine behaviour, in the form of unexpected N1 variations and/or illumination of the "GOV'' warning light. The conclusions from an investigation by Turbom[eacute]ca are that these malfunctions are due to a lapse of quality control in the varnishing process applied to the boards, and that only boards in a specific serial number range, as defined under "Applicability'' and referred to below as the "suspect batch'', are affected. We are issuing this AD to prevent loss of automatic engine control during flight due to an uncommanded engine roll-back, which could result in the inability to continue safe flight.
2004-03-19: This amendment supersedes an existing airworthiness directive (AD), applicable to certain Airbus Model A320-111, -211, and -231 series airplanes, that currently requires repetitive inspections for cracking in the transition and pick-up angles in the lower part of the center fuselage area, and corrective action if necessary. That AD also provides for an optional terminating modification for the repetitive inspection requirements. This amendment reduces the compliance time for the inspections for cracking of the same area. The actions specified by this AD are intended to detect and correct fatigue cracking in the transition and pick-up angles of the lower part of the center fuselage, which could result in reduced structural integrity of the wing-fuselage support and fuselage pressure vessel. This action is intended to address the identified unsafe condition.
2021-03-02: The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) CF6-80C2A1, CF6-80C2A2, CF6- 80C2A3, CF6-80C2A5, CF6-80C2A5F, CF6-80C2A8, CF6-80C2B1, CF6-80C2B1F, CF6-80C2B2, CF6-80C2B2F, CF6-80C2B4, CF6-80C2B4F, CF6-80C2B5F, CF6- 80C2B6, CF6-80C2B6F, CF6-80C2B6FA, CF6-80C2B7F, CF6-80C2B8F, and CF6- 80C2D1F model turbofan engines. This AD was prompted by reports of incidents that resulted in a significant fuel loss during flight and an in-flight shutdown (IFSD) of the engine. This AD requires initial and repetitive shim checks of the hydromechanical unit/main engine control (HMU/MEC) idler adapter on the accessory gearbox (AGB) assembly and, depending on the results of the shim check, possible replacement of the inserts on the HMU/MEC idler adapter. As a terminating action, this AD requires a protrusion check and a pull-out test, and the replacement of inserts on the HMU/MEC idler adapter that fail either test. The FAA is issuing this AD to address the unsafe condition on these products.
95-17-06: This amendment adopts a new airworthiness directive (AD) that applies to Mooney Aircraft Corporation (Mooney) Model M20K airplanes with a Continental TSIO-520-NB engine installed in accordance with Supplemental Type Certificate (STC) SA5691NM. This action requires repetitively inspecting the exhaust transition tube and turbo mount assembly for cracks, and replacing any part found cracked. A report of a cracked exhaust transition tube that connects the exhaust manifolds to the turbocharger inlet on one of the affected airplanes prompted this action. The actions specified by this AD are intended to prevent exhaust gases from entering the cabin heating system because of a cracked exhaust transition tube, which, if not detected and corrected, could result in hazardous levels of carbon monoxide in the airplane cabin.
2004-03-07: This amendment adopts a new airworthiness directive (AD), applicable to certain Airbus Model A320-111, -211, -212, and -231 series airplanes. This AD requires repetitive inspections for fatigue cracking around the fasteners attaching the pressure panel to the flexible bracket at frame 36, adjacent to the longitudinal beams on the left and right sides of the airplane; and repair as necessary. This AD would also provide an optional terminating action for the repetitive inspections. This action is necessary to detect and correct fatigue cracking around the fasteners attaching the pressure panel to the flexible bracket at the frame 36 adjacent to the longitudinal beams, which could result in reduced structural integrity and possible rapid decompression of the airplane. This action is intended to address the identified unsafe condition.
96-25-13: This amendment adopts a new airworthiness directive (AD), applicable to certain Jetstream Model 4101 series airplanes, that requires a high frequency eddy current inspection to detect cracks of the boundary angle and joint angle of the rear pressure bulkhead, and repair, if necessary. This amendment also requires modification of the rear pressure bulkhead of the fuselage. This amendment is prompted by a report of fatigue cracking in the rear pressure bulkhead of the fuselage. The actions specified by this AD are intended to prevent such fatigue cracking, which could result in reduced structural integrity of the fuselage and, consequently, lead to the rapid decompression of the pressurized area of the airplane.